John Lewis TULIP User manual

John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Made in China Please retain these instructions for future reference.
5 year guarantee
Aftercare and
Troubleshooting
Max. power: 4W
Voltage: 220–240V, 50Hz
IP rating: 20
Weight: 0.47kg
At John Lewis & Partners we test every light to high quality standards so we are
able to offer you a 5 year guarantee.
Specification
Recycling
Caring for
your product
We recommend cleaning with a soft dry cloth.
Do not use abrasive materials as these will damage the finish.
Replace bulbs from John Lewis or established brand of the same type and
compatibility.
This symbol indicates that this product should not be treated as normal
household waste and it should be recycled. John Lewis & Partners do not
operate instore take back, but as members of the Distributor Take Back
scheme have funded the development and upgrade of recycling facilities across
the UK. Please take it to your nearest collection facility or for further details
contact your local council or visit www.recycle-more.co.uk.
TULIP WALL LAMP
USER GUIDE
Please ensure all screws and small pieces are properly tightened to the product.
When changing a bulb, always switch off the mains and allow the bulb to cool
down before handling.
A bulb’s watt rating indicates how much energy it uses. The higher the watt,
the more energy it requires. Lumens is a measure of brightness. The higher
the number of lumens, the brighter the light.

01 02
Description Image Quantity Parts list
Introduction Thank you for purchasing this Tulip Wall Lamp.
Please read the instructions carefully before
use to ensure safe and satisfactory operation
of this product.
Warnings
G9 LED Bulb only
Canopy 1 PC
1 PC
1 PC
2PCS
1 x 4 watt energy efficient G9 LED
Bulb replaceable
Bulb not included
Recommended
bulb
Product assembly
1
3
2
Place the canopy of lamp body (A) over the
bracket (E) with scews (D). Tighten screws
(D) to make sure fixture is secured.
Install the G9 LED bulb into the socket of lamp
body (B).
Note: Turn Lamp on and off with the toggle
switch on canopy.
4
E
A
Lamp Body
B
Shade
C
D
1 PC
Scews
EBracket
AA
D
D
E
E
This fitting is for indoor use only.
This product is Class II and must not be earthed.
For your safety, this product must be installed in accordance with local Building
Regulations. If in any doubt, or where required by the law, consult a competent
person who is registered with an electrical self-certication scheme. Further informa-
tion is available online or from your local authority. In accordance with regulations,
the product ceilling rose, terminal blocks and any connectors shall not be fixed in
full or partial recess.
Never install your appliance on a wet, freshly painted or plastered surface. To pre-
vent electric shock, switch off the mains supply before installing or maintaining this
product. Ensure no one else can restore eletricity supply without your knowledge,
while in stalling the wall lamp. Always use the correct type and rating bulb.
If removing an existing fitting, please write down all wiring connections.
When changing a bulb, always switch off at the mains and allow the old bulb to cool
down before handing. Dispose of used bulbs carefully.
The bulb and surrounding parts can become extremely hot during use.
The supply cord cannot be replaced. If the cord is damaged the product should be
disposed of to avoid a safety hazard.
Do not over tighten the glass shades. If the shades are screwed down too tight the
glass could be break.
Do not use a G9 LED bulb longer than 6cm to avoid puncturing the glass shade.
The bulb is not included with this lamp. Please visit your local store to purchase the
bulb prior to assembly.
Make electrical connections on terminal block
as shown. Connect supply live (normally
brown or red color) to fitting live (marked
“L”) on the terminal block. Connect supply
neutral (normally blue or black color) to fit-
ting neutral (marked “N”) on the terminal
block. Ensure electrical connections are tight
and no loose strands of wire are left out of
the connector block. Place terminal block
into the black protection box, and screw in
the position.
Carefully unpack the carton, making sure all
parts are included before assembly. Place
lamp parts on a flat surface.
Secure the bracket (E) to wall with screws.
2 pcs
2 pcs
E
Note: 2 screws and 2 plastic bolts are pur-
chase separately, they are not included in
the packaging.