JUMO TAROS S47 P User manual

40207200T90Z001K000
V1.00/EN/00740059/2020-12-09
JUMO TAROS S47 P
Pressure transmitter
Operating Manual

Contents
Contents
1 Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3 Identifying the device version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Nameplate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3.2 Order details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3.3 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2.1 Transmitter with electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2.2 Process connections, not front-flush. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.2.3 Process connections, front-flush. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 Installation notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.2 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.1 Zero point adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
7 Maintenance, cleaning and returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
7.2 Manual cleaning for maintenance or storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
7.3 Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
8 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.1 Mechanical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
8.2 Measuring range and accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
8.3 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
8.4 Environmental influences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
9 China RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4
1 Safety information
1 Safety information
General
This manual contains information that must be observed in the interest of your own safety and to avoid
material damage. This information is supported by symbols which are used in this manual as indicated.
Please read this manual before starting up the device. Store this manual in a place that is accessible to
all users at all times.
If difficulties occur during startup, please do not intervene in any way that could jeopardize your warranty
rights!
Warning symbols
DANGER!
This symbol indicates that personal injury from electrocution may occur if the appropriate precaution-
ary measures are not taken.
WARNING!
This symbol in connection with the signal word indicates that personal injury may occur if the respective
precautionary measures are not carried out.
CAUTION!
This symbol in connection with the signal word indicates that material damage or data loss will occur
if the respective precautionary measures are not taken.
CAUTION!
This symbol indicates that components could be destroyed by electrostatic discharge (ESD = Electro
Static Discharge) if the respective cautionary measures are not taken.
Only use the ESD packages intended for this purpose to return device inserts, assembly groups, or as-
sembly components.
Note symbols
NOTE!
This symbol refers to important information about the product, its handling, or additional benefits.
REFERENCE!
This symbol refers to additional information in other sections, chapters, or other manuals.
FURTHER INFORMATION!
This symbol is used in tables and indicates that further information is provided after the table.
&
DISPOSAL!
At the end of its service life, the device and any batteries present do not belong in the trash! Please en-
sure that they are disposed of properly and in an environmentally friendly manner.

5
2 Introduction
2Introduction
2.1 Description
The pressure transmitter is used to acquire relative and absolute pressures in liquid and gaseous media.
The JUMO TAROS S47 P with an analog output signal has a pressure measuring cell with a piezoresis-
tive silicon sensor. The pressure is converted into an electrical current or voltage signal and output via
various electrical connections.
A built-in magnetoresistive switch (MRS) enables the user to adjust the zero point of the device exter-
nally using a magnet.
UL and EAC approvals for the pressure transmitter are currently being prepared.
2.2 Block diagram
Voltage supply
DC 8 to 30 V with two-wire
output (4 to 20 mA)
DC 11,5 bis 30 V with three-wire
output (0 to 10 V)
DC 10 to 30 V with three-wire
output (1 to 5 V and 1 to 6 V)
Pressure transmitter
Operation
Zero point correction with magnet
Measurand
Relative pressure
Absolute pressure
Output signal
Two-wire: 4 to 20 mA
Three-wire: DC 0 to 10 V or
DC 1 to 5 V or
DC 1 to 6 V

6
3 Identifying the device version
3 Identifying the device version
3.1 Nameplate
Position
The nameplate is laser-etched on the device surface.
Contents
The nameplate shows important information. This includes:
Device type (Typ)
Compare the specifications on the nameplate with your order documents. The supplied device version
can be identified using the order code (chapter 3.2 "Order details", Page 7).
Part no. (TN)
The part no. uniquely identifies an article in the catalog. It is important for communication between the
customer and the sales department.
Fabrication number (F-Nr)
Among other things, the fabrication number indicates the production date (year/week) and the hardware
version number.
Production date
Example: F-Nr = 0123456701020490123.
Here, we are looking at the 12th to the 15th digit (from the left).
In this example, the device was produced in the year 2020, in the 49th week.
Description Designation on the nameplate Example
Device type Type 402072/000
Part no. TN 00123456
Measuring range 0 to 0.1 bar relative pressure
Voltage supply DC 8 to 30 V
Output signal 4 to 20 mA
Fabrication number F no. 0123456701020490123

7
3 Identifying the device version
3.2 Order details
(1) Basic type
402072 JUMO TAROS S47 P – pressure transmitter
(2) Basic type extension
000 None
051 Relative-pressure version without zero point adjustment
999 Special version
(3) Input
478 -1 to 0 bar relative pressure
479 -1 to +0.6 bar relative pressure
449 -1 to +1 bar relative pressure
480 -1 to +1.5 bar relative pressure
481 -1 to +3 bar relative pressure
482 -1 to +5 bar relative pressure
483 -1 to +9 bar relative pressure
484 -1 to +15 bar relative pressure
485 -1 to +24 bar relative pressure
428 -0.4 to +0.4 bar relative pressure
427 -0.1 to +0.1 bar relative pressure
425 0 to 0.1 bar relative pressure
426 0 to 0.16 bar relative pressure
451 0 to 0.25 bar relative pressure
452 0 to 0.4 bar relative pressure
453 0 to 0.6 bar relative pressure
454 0 to 1 bar relative pressure
455 0 to 1.6 bar relative pressure
456 0 to 2.5 bar relative pressure
457 0 to 4 bar relative pressure
458 0 to 6 bar relative pressure
459 0 to 10 bar relative pressure
460 0 bar to 16 bar relative pressure
461 0 bar to 25 bar relative pressure
462 0 bar to 40 bar relative pressure
463 0 bar to 60 bar relative pressure
464 0 bar to 100 bar relative pressure
487 0 to 0.6 bar absolute pressure
488 0 to 1 bar absolute pressure
489 0 to 1.6 bar absolute pressure
490 0 to 2.5 bar absolute pressure
491 0 to 4 bar absolute pressure
500 0 to 5 bar absolute pressure
492 0 to 6 bar absolute pressure
493 0 to 10 bar absolute pressure
494 0 to 16 bar absolute pressure
495 0 to 25 bar absolute pressure

3 Identifying the device version
8
505 0 to 40 bar absolute pressure
998 Special measuring range for absolute pressure
999 Special measuring range for relative pressure
(4) Output
405 4 to 20 mA, two-wire
415 DC 0 to 10 V, three-wire
418 DC 1 to 5 V, three-wire
420 DC 1 to 6 V, three-wire
(5) Process connection
502 G 1/4 DIN EN 837
504 G 1/2 DIN EN 837
511 1/4-18 NPT DIN EN 837
512 1/2-14 NPT DIN EN 837
521 G 1/4 DIN 3852-11
523 G 1/2 DIN 3852-11
562 7/16-20 UNF
571 G 3/4 front-flush DIN EN ISO 228-1
574 G 1/2 front-flush with double seal
575 G 3/4 front-flush with double seal
576 G 1 front-flush with double seal
(6) Process connection material
20 Stainless steel
(7) Electrical connection
12 Attached cable, shielded
36 Round plug M12 × 1
61 Line socket DIN EN 175301-803, form A
75 Terminal head
(8) Measuring system, filling medium
01 Silicone oil
(9) Extra codes
000 None
374 Inspection certificate 3.1 EN 10204 – material
462 Inverted output signal
624 Oil and grease free
769 Calibration certificate

9
3 Identifying the device version
3.3 Accessories
(1) (2) (3) (4) (5) (6) (7) (8) (9)
Order code / - - ----/
Order example 402072 / 000 - 491 - 405 - 504 - 20 - 61 - 01 / 000
Item Part no.
Line socket, 4-pole, M12 × 1, straight, with 2-m PVC cable, without pressure compensation 00404585
Line socket, 4-pole, M12 × 1, angled, with 2-m PVC cable, without pressure compensation 00409334
Magnetic pin for simple adjustment of zero point 00736330

10
4 Mounting
4 Moun ting
4.1 General information
NOTE!
Check that the device is compatible with the measurement medium chapter 8.4 "Environmental in-
fluences", Page 20.
Mounting site
• Ensure that the device is fastened safely and with low vibrations
• Avoid direct sunlight
• Please note the admissible ambient temperatures at the installation position 
chapter 8.4 "Environmental influences", Page 20
Installation position
The device can be installed in any position.
We recommend the "upright" installation position, as shown below:

11
4 Mounting
4.2 Dimensions
4.2.1 Transmitter with electrical connections
12 36
Attached cable, length of 2 m (standard) Round plug M12 × 1
61 75
Line socket DIN EN 175301-803, form A Terminal head
PA = process connection

4 Mounting
12
4.2.2 Process connections, not front-flush
502 504
G 1/4 DIN EN 837 G 1/2 DIN EN 837
511 512
1/4-18 NPT DIN EN 837 1/2-14 NPT DIN EN 837
521 523
G 1/4 DIN 3852-11 G 1/2 DIN 3852-11
Profile sealing ring G 1/4 Profile sealing ring G 1/2

13
4 Mounting
4.2.3 Process connections, front-flush
562
7/16-20 UNF
571 574
G 3/4 DIN EN ISO 228-1 G 1/2 with double seal
575 576
G 3/4 with double seal G 1 with double seal
Profile sealing ring G 3/4 O-ring 15.1 × 1.6
Profile sealing ring G 1/2 O-ring 20.35 × 1.78
Profile sealing ring G 1 O-ring 26.7 × 1.78

14
5 Electrical connection
5 Electrical connection
5.1 Installation notes
NOTE!
The electrical connection must only be performed by qualified personnel.
5.2 Connection diagram
The electromagnetic compatibility meets standard DIN EN 61326.
Do not connect any additional loads to the voltage supply of the device.
The device is not suitable for installation in potentially explosive areas.
Connection Terminal assignmenta
12 36 61 75
Attached cable Round plug
M12 × 1
Cable socket Terminal head
4 to 20 mA, 2-wire (output 405)
Voltage supply DC 8 to 30 V UB/S+White111
0V/S-Black322
DC 0 to 10 V, 3-wire (output 415)
Voltage supply DC 11.5 V to 30 V UBWhite111
0V/S-Black222
S+ Yellow 3 3 3
DC 1 to 5 V, three-wire (output 418)
DC 1 to 6 V, three-wire (output 420)
Voltage supply DC 10 to 30 V UBWhite111
0V/S-Black222
S+ Yellow 3 3 3
Functional bonding conductor FBb
(all output variants)
Shield/green 4 4
aFigure: Connection to the pressure transmitter
bAs a basic principle, the device is grounded via the process connection. Alternatively, the device can also be
grounded via the electrical connection on all variants. However, grounding via both the process connection and the
electrical connection is not admissible.
1
4
2
3
1
2
3
1234
Admissible effect on the "attached
cable" variant
Smallest bending radius (fixed) 40 mm
Max. tensile force on the cable 20 N

15
6 Operation
6Operation
6.1 Zero point adjustment
General information
In the case of device versions designed for relative pressure, there is the option of a simple pressure/
zero point adjustment (offset) using a magnet (remanence BR≥ 1 T, e.g. NdFeB dia. 4 mm × 10 mm).
This actuates a magnetoresistive switch inside the device when approaching it. A suitable magnet is
available from JUMO as an accessory (part no. 00736330).
This provides a quick and simple way to correct zero point offsets caused by the installation or zero point
offsets that have arisen following autoclaving, for example.
Requirements
The following conditions must be met in order to carry out a successful zero point adjustment:
• The adjustment must take place within a timeframe of a maximum of 2 seconds once the device
is switched on.
• The pressure at the device at the point of the zero point adjustment must not deviate more than
±10 % from the positive pressure measuring range of the device1.
Procedure
NOTE!
If the magnetic field is not applied within the timeframe of approx. 2 seconds after the device is switched
on, it will not affect the zero point of the device.
A further zero point adjustment can only take place once the device has been switched off and switched
back on again.
1Example 1: Measuring range 0 to 1 bar rel.; deviation from ambient pressure max. ±0.1 bar.
Example 2: Measuring range -1 to +0.6 bar rel.; deviation from ambient pressure max. ±0.1 bar.
Example 3: Measuring range -1 to 5 bar rel.; deviation from ambient pressure max. ±0.5 bar.
1. Hold the magnet at the position of the QR
code (1) on the nameplate of the device.
2. Switch on the voltage supply for the de-
vice.
The device recognizes the magnet (within
the first 2 seconds) and automatically re-
adjusts the zero point. As a result, the
switch-on time is slightly delayed
3. Remove the magnet from the housing and
keep it for further use.
The zero point adjustment is complete. The
new zero point is permanently saved. Howev-
er, you can carry out a further zero point ad-
justment at any time.

16
7 Maintenance, cleaning and returns
7 M aint enan ce, cle ani ng and ret ur ns
7.1 Maintenance
The pressure transmitter is maintenance-free.
In the event of a malfunction, please return the device to the manufacturer together with accurate fault
information.
7.2 Manual cleaning for maintenance or storage
The pressure transmitter – especially the parts in contact with the product – must not be damaged. Any
damage to the stainless steel membrane must be avoided. The cleaning agent must not attack the sur-
face and seals.
Note the protection type of the device.
7.3 Returns
NOTE!
In case of abnormalities, please send the device to the manufacturer together with a completed cover
note for product returns. You can download a blank copy of this cover note online at:
http://produktruecksendung.jumo.info.

17
8 Technical data
8 Tech ni cal da ta
8.1 Mechanical features
8.2 Measuring range and accuracy
Materials of parts coming into contact
with the pressurized medium
Membrane Stainless steel 1.4435 (316L)
O-ring/sealing ring FPM, others available as an optional extra (e.g. EPDM, VMQ)
Process connection Stainless steel 1.4571 (316Ti)
Welding ring Stainless steel 1.4404 (316L)
Materials of other parts
Housing Stainless steel 1.4301 (304)
Electrical connection
Attached cable Cable fitting made from stainless steel 1.4301 (304); PUR cable with and
without pressure compensation
Round plug M12 × 1 Threaded bushing made from stainless steel 1.4301 (304)
Line socket Holding ring/connector fastener made from high-quality plastic, comparable
with PBT GF30 V0
Terminal head Stainless steel 1.4301 (304); cable fitting: stainless steel
Rated position Upright, with downward process connection
Operating position Any, but there may be a zero offset relative to the rated position
Measuring range LinearityaAccuracy at Long-
term
stabilityb
Overload
capabili-
tyc
Burst
pressure
20 °Cd-20 to
+80 °Ce
-20 to
+100 °C
% MSPf% MSP % MSP % MSP % MSP
per year
bar bar
-1 to 0 bar relative pressure 0.15 0.3 1 1.2 ≤ 0.15 10 20
-1 to +0.6 bar relative pressure 0.15 0.3 1 1.2 ≤ 0.15 10 20
-1 bar to +1 bar relative pressure 0.15 0.3 1 1.2 ≤ 0.15 10 20
-1 to +1.5 bar relative pressure 0.15 0.3 1 1.2 ≤ 0.15 20 40
-1 to +3 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 25 50
-1 to +5 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 50 60
-1 to +9 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 50 60
-1 to +15 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 120 200
-1 to +24 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 120 200
-0.4 to +0.4 bar relative pressure 0.15 0.4 1 1.2 ≤ 0.2 10 20
-0.1 to +0.1 bar relative pressure 0.2 0.5 1 1.2 ≤ 0.2 6 10
0 to 0.1 bar relative pressure 0.25 0.75 1.2 1.5 ≤ 0.2 1.5 3
0 to 0.16 bar relative pressure 0.25 0.75 1.2 1.5 ≤ 0.2 6 10
0 to 0.25 bar relative pressure 0.25 0.5 1 1.2 ≤ 0.2 6 10
0 to 0.4 bar relative pressure 0.15 0.4 1 1.2 ≤ 0.15 10 20
0 to 0.6 bar relative pressure 0.15 0.4 1 1.2 ≤ 0.15 10 20
0 to 1 bar relative pressure 0.15 0.3 1 1.2 ≤ 0.15 10 20
0 to 1.6 bar relative pressure 0.15 0.3 1 1.2 ≤ 0.15 20 40
0 to 2.5 bar relative pressure 0.15 0.3 1 1.2 ≤ 0.1 20 40
0 to 4 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 25 50

8 Technical data
18
0 to 6 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 50 60
0 to 10 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 50 60
0 bar to 16 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 120 200
0 bar to 25 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 120 200
0 bar to 40 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 300 400
0 bar to 60 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 300 400
0 bar to 100 bar relative pressure 0.1 0.25 0.75 0.8 ≤ 0.1 300 400
0 to 0.6 bar absolute pressure 0.15 0.4 1 1.2 ≤ 0.15 10 20
0 to 1 bar absolute pressure 0.15 0.3 1 1.2 ≤ 0.15 10 20
0 to 1.6 bar absolute pressure 0.15 0.3 1 1.2 ≤ 0.15 20 40
0 to 2.5 bar absolute pressure 0.15 0.3 1 1.2 ≤ 0.1 20 40
0 to 4 bar absolute pressure 0.1 0.25 0.75 0.8 ≤ 0.1 25 50
0 to 5 bar absolute pressure 0.1 0.25 0.75 0.8 ≤ 0.1 25 50
0 to 6 bar absolute pressure 0.1 0.25 0.75 0.8 ≤ 0.1 50 60
0 to 10 bar absolute pressure 0.1 0.25 0.75 0.8 ≤ 0.1 50 60
0 to 16 bar absolute pressure 0.1 0.25 0.75 0.8 ≤ 0.1 120 200
0 to 25 bar absolute pressure 0.1 0.25 0.75 0.8 ≤ 0.1 120 200
0 to 40 bar absolute pressure 0.1 0.25 0.75 0.8 ≤ 0.1 200 300
aLinearity according to limit point setting
bReference conditions EN 61298-1
cAll measuring ranges are vacuum proof.
dIncludes: linearity, hysteresis, repeatability, deviation of measuring range start value (offset) and measuring range
end value
eIncludes: linearity, hysteresis, repeatability, deviation of measuring range start value (offset) and measuring range
end value, thermal effect on measuring range start (offset) and measuring span
fMSP = measuring span
Measuring range LinearityaAccuracy at Long-
term
stabilityb
Overload
capabili-
tyc
Burst
pressure
20 °Cd-20 to
+80 °Ce
-20 to
+100 °C
% MSPf% MSP % MSP % MSP % MSP
per year
bar bar

19
8 Technical data
8.3 Electrical data
Voltage supplya
Two-wire
4 to 20 mA DC 8 to 30 V, nominal voltage DC 24 Vb
Three-wire
DC 0 to 10 V DC 11.5 V to 30 V, nominal voltage DC 24 V
DC 1 to 5 V DC 10 V to 30 V, nominal voltage DC 24 V
DC 1 to 6 V DC 10 V to 30 V, nominal voltage DC 24 V
aThe auxiliary energy of the pressure transmitter must meet SELV requirements. Furthermore, the device must be
equipped with an electrical circuit that meets the requirements of EN 61010-1 with regard to "Limited-energy cir-
cuits".
bMaximum current consumption ≤ 30 mA.
Burden/loada
Two-wire
4to20mA R
L≤ (UB -8 V) ÷ 0.02 A (Ω)
Three-wire
DC 0 to 10 V RL≥ 10 kΩ
DC 1 to 5 V RL≥ 10 kΩ
DC 1 to 6 V RL≥ 10 kΩ
aMaximum effect < 0.5 %.
Behavior if measured value is out of
range
Error signal in the case of NAMUR exceedance, linear
Two-wire
4 to 20 mA ≤ 3.6 mA and ≥ 21.5 mA 3.8 to 20.5 mA
Three-wire
DC0to10V 10.7V 0to10.5V
DC 1 to 5 V 5.7 V 0.8 to 5.5 V
DC 1 to 6 V 6.7 V 0.8 to 6.5 V
Behavior after power on Ready for operation after < 120 ms
Voltage supply influence ≤ 0.02 %/V
Reverse voltage protection UB to 0 V (all output variants)
Short-circuit resistance S+ to 0 V (only voltage variants)
Overvoltage protection The operating voltage must be restricted to max. 33 V
Step response of 90 % (according
to DIN 16068 Point 3.3.8)
<5ms
Insulation resistance > 100 MΩ at DC 500 V
Insulation voltage AC 500 V

8 Technical data
20
8.4 Environmental influences
Admissible temperatures
Ambient temperature Medium temperature Storage temperature
with MSPa≤ 0.4 bar -20 to +85 °C -20 °C to +125 °C -20 to +100 °C
with MSP > 0.4 bar -40 to +85 °C -40 to +125 °C -40 to +100 °C
aMSP = measuring span
Resistance to climatic conditions 100 % relative humidity including condensation on the device's outer case;
90 % relative humidity without condensation
Protection type According to DIN EN 60529
Types with attached cable IP68a (IP66/IP68)
Types with round plug M12 × 1 IP67 (IP66/IP67)
Types with line socket IP65
Types with terminal head IP69 (IP66/IP69)
Admissible mechanical load
Vibration resistance 20 g at 10 to 2000 Hz, 10 cycles per axis, device in X, Y, Z axis,
industrial requirement according to IEC 60068-2-6
Shock resistance 50 g for 11 ms and 100 g for 1 ms,
industrial requirement according to IEC 60068-2-27
Electromagnetic compatibility
(EMC)
According to DIN EN 61326-2-3
Interference emission Class A – only for industrial use –
Interference immunity Industrial requirement
Process media Liquid and gaseous media which are compatible with the materials of the parts
coming into contact with the pressurized medium
aFor 1 h at a depth of 2 m.