Kaba Solitaire 710-II Series User manual

PK2943
INSTALLATION
INSTRUCTIONS
Solitaire 710-II
SolitaireSMART
Knob Retrofit Kit

710-11/SMART Retrofit Installation Instructions • PK2943
Page 2
Kit Contents
!
!
Warning: Installation of this kit by the end
user may cancel the complete lock
warranty. Kaba Ilco is not responsible
for any damage caused by installation.
Kit part #062-510479-XXX
1. Short extension spring
2. Long extension spring
3. Short half-spindle
4. Spare retaining ring
5. Sleeve
6. Insert
7. Knob
NOTE:
The Solitaire 710-II
outside housing is
illustrated throughout
these instructions. The
same steps apply to
the SolitaireSMART (740)
outside housing, with
only minor differences
in the appearance of
the trim.
LOCK HANDING
Before installing the
knob, remove the lock
from the door and
check the handing of
the outside housing.
IMPORTANT: DO NOT install the knob
on the insert before instructed to do
so. The retaining ring (4) will be difficult to
install if the knob (7) is already assembled
on the insert (6). Left-hand
LH
Right-hand
RH

Step by Step Instructions
710-11/SMART Retrofit Installation Instructions • PK2943
Page 3
Remove spindle and
compression spring.
1
Remove extension spring.
2
Remove retaining ring.
3
Outside Housing

710-11/SMART Retrofit Installation Instructions • PK2943
Page 4
Disassemble stop plate
(A), bushing (B) and lever.
Assemble insert (D) and
sleeve (C) from kit with
existing nylon bushing
(B) and stop plate (A).
B
A
!Check handing
LH RH
B
A
CD
4
5
Step by Step Instructions (cont)
Outside Housing

710-11/SMART Retrofit Installation Instructions • PK2943
Page 5
LH
RH
TIP: Pry up the
groove in the
insert if necessary.
Closed
end to
hook
Reattach retaining ring in
position shown.
6
Connect the long
extension spring from the
knob kit between the stop
plate and the hook on the
housing.
7
Outside Housing
Step by Step Instructions (cont)

710-11/SMART Retrofit Installation Instructions • PK2943
Page 6
Assemble the knob on
the insert. Ensure it clips
in place.
8
Insert short half-spindle
from kit and compression
spring
9
Outside Housing
IMPORTANT: See notes at the end of this
document before reinstalling lock on door.
TIP: The tooth
inside the knob
engages the slot
on the insert.
Step by Step Instructions (cont)

710-11/SMART Retrofit Installation Instructions • PK2943
Page 7
Step by Step Instructions (cont)
Remove spindle and
compression spring.
Unscrew two Phillips
screws.
1.1
Remove extension spring.
2
Remove retaining ring.
3
Inside Housing
A
C
B
Remove plate.
Remove override
cam (A), gear (B) and
felt washer (C).
1.2

710-11/SMART Retrofit Installation Instructions • PK2943
Page 8
Disassemble stop plate
(A), bushing (B) and lever.
4
Assemble insert (D) and
sleeve (C) from kit with
existing nylon bushing (B)
and stop plate (A).
5
Inside Housing
Step by Step Instructions (cont)
B
A
Check handing
CD
B
LH RH
A

710-11/SMART Retrofit Installation Instructions • PK2943
Page 9
Reattach retaining
ring in position
shown.
6
Inside Housing
Step by Step Instructions (cont)
LH
RH
TIP: Pry up the
groove in the
insert if necessary.
Closed
end to
hook
Connect the short
extension spring
from the knob kit
between the stop
plate and the hook
on the housing.
7.1

710-11/SMART Retrofit Installation Instructions • PK2943
Page 10
If the thumbturn
has a pin, position
the pin as shown.
7.2
Inside Housing
Step by Step Instructions (cont)
LH
RH
POINT MARK
DOT
MARK
DOT
POINT
PCB
MARK
PIN
Install override gear,
override cam, and
felt washer.
7.3