KERR OptiBond Solo Plus User manual

Refer to complete Directions for Use booklet regarding specifics by indication
for both Direct and Indirect application.
Technique Summary

kerrdental.com/optibondsp

CAUTION: Contains phosphoric acid. Avoid contact
with skin, eyes and soft tissue. In case of contact
with skin or eyes, flush immediately with water.
Get medical attention for eyes. Do not take internally.
* CAUTION: Uncured methacrylate resin may cause
contact dermitis and damage the pulp. Avoid
contact with skin, eyes and soft tissue. In case of
contact with skin or eyes, Wash thoroughly with
water after contact.
** Recommended Cure Times: The Demi™, 5 seconds,
L.E.Demetron II, 5 seconds; L.E.Demetron I, 10
seconds; or Optilux™501 in Boost mode 10 seconds,
Ramp mode 20 seconds or Regular mode, 20
seconds. For all other lights, see manufacturer’s
recommendation.
***
Etch* enamel and dentin for
15 seconds. Rinse for 15
seconds and gently air dry.
Do not desiccate.
1. Place composite and
light cure.***
4.Air thin for 3 seconds. Avoid
pooling. Light cure.***
3.Apply OptiBond Solo Plus**
for 15 seconds using light
brushing motion.
2.
Direct Technique

CAUTION: Contains phosphoric acid. Avoid contact
with skin, eyes and soft tissue. In case of contact
with skin or eyes, flush immediately with water.
Get medical attention for eyes. Do not take internally.
* CAUTION: Uncured methacrylate resin may cause
contact dermitis and damage the pulp. Avoid
contact with skin, eyes and soft tissue. In case of
contact with skin or eyes, Wash thoroughly with
water after contact.
** Recommended Cure Times: The Demi™, 5 seconds,
L.E.Demetron II, 5 seconds; L.E.Demetron I, 10
seconds; or Optilux™501 in Boost mode 10 seconds,
Ramp mode 20 seconds or Regular mode, 20
seconds. For all other lights, see manufacturer’s
recommendation.
***
Gently seat restoration.
Remove excess cement.
5.Select appropriate shade of
base luting resin and place
into restoration according to
manufacturer’s instructions.
4. Light cure all surfaces.***
Polish margins with
appropriate materials.
6.
Etch* enamel and dentin for 15
seconds. Rinse for 15 seconds and
gently air dry. Do not desiccate.
1. Apply OptiBond Solo Plus**
for 15 seconds using light
brushing motion.
2. Air thin for 3 seconds.
Avoid pooling. Light cure.***
3.
Veneers

CAUTION: Contains phosphoric acid. Avoid contact
with skin, eyes and soft tissue. In case of contact
with skin or eyes, flush immediately with water.
Get medical attention for eyes. Do not take internally.
* CAUTION: Uncured methacrylate resin may cause
contact dermitis and damage the pulp. Avoid
contact with skin, eyes and soft tissue. In case of
contact with skin or eyes, Wash thoroughly with
water after contact.
** Recommended Cure Times: The Demi™, 5 seconds,
L.E.Demetron II, 5 seconds; L.E.Demetron I, 10
seconds; or Optilux™501 in Boost mode 10 seconds,
Ramp mode 20 seconds or Regular mode, 20
seconds. For all other lights, see manufacturer’s
recommendation.
***
Gently seat restoration.
Remove excess cement.
5.Select appropriate shade of
resin cement (NX3). Refer to
manufacturer’s instructions.
4. Light cure all surfaces.***6.
Etch* enamel and dentin for 15
seconds. Rinse for 15 seconds and
gently air dry. Do not desiccate.
1. 2. Apply OptiBond Solo Plus** for 15
seconds using light brushing motion.
Air thin for 3 seconds. Avoid pooling.
Light cure all surfaces.***
3.
Crowns, Inlays, Onlays

CAUTION: Contains phosphoric acid. Avoid contact
with skin, eyes and soft tissue. In case of contact
with skin or eyes, flush immediately with water.
Get medical attention for eyes. Do not take internally.
* CAUTION: Uncured methacrylate resin may cause
contact dermitis and damage the pulp. Avoid
contact with skin, eyes and soft tissue. In case of
contact with skin or eyes, Wash thoroughly with
water after contact.
** Recommended Cure Times: The Demi™, 5 seconds,
L.E.Demetron II, 5 seconds; L.E.Demetron I, 10
seconds; or Optilux™501 in Boost mode 10 seconds,
Ramp mode 20 seconds or Regular mode, 20
seconds. For all other lights, see manufacturer’s
recommendation.
***
Etch* enamel and dentin for 15
seconds. Rinse for 15 seconds and
gently air dry. Do not desiccate.
1.
Apply cement to post. Seat
post. Remove excess cement.
5.
Apply OptiBond Solo Plus to
post. Air dry for 3 seconds.
Light cure.***
2.
Light cure all surfaces.***6.
Select appropriate shade of
NX3 and place into restoration.
4.
Apply OptiBond Solo Plus** for 15 seconds
using light brushing motion. Air thin for 3
seconds. Avoid pooling. Light cure.***
3.
Posts

CAUTION: Contains phosphoric acid. Avoid contact
with skin, eyes and soft tissue. In case of contact
with skin or eyes, flush immediately with water.
Get medical attention for eyes. Do not take internally.
* CAUTION: Uncured methacrylate resin may cause
contact dermitis and damage the pulp. Avoid
contact with skin, eyes and soft tissue. In case of
contact with skin or eyes, Wash thoroughly with
water after contact.
** Recommended Cure Times: The Demi™, 5 seconds,
L.E.Demetron II, 5 seconds; L.E.Demetron I, 10
seconds; or Optilux™501 in Boost mode 10 seconds,
Ramp mode 20 seconds or Regular mode, 20
seconds. For all other lights, see manufacturer’s
recommendation.
***
Etch* enamel and dentin for 15
seconds. Rinse for 15 seconds and
gently air dry. Do not desiccate.
1. Light cure all surfaces.***3.
Build remaining core in
bulk. Light cure***
6.Light cure all surfaces.***5.
Apply OptiBond Solo Plus for 15
seconds using light brushing motion.
Air thin for 3 seconds. Avoid pooling.
2.
Core Materials
Apply core material
in 2 mm increments.
Note: Avoid using self-cure mode. Always light cure core material.
4.

kerrdental.com/optibondsp
800.KERR.123
79604 Rev 0
©2009 Kerr Corporation
Printed in USA