Keys Fitness 2250 User manual

Owner’s Manual
Read all precautions and instruc-
tions in this manual before using
this equipment.
215-00013
10/04

Table of Contents
2
Important Safety Information 3
Before You Start 4
Assembly 5-34
Weight Ratios 35
Weight Stack Sticker Placement 36
Cable View 37-38
Top View 39
Exploded View 40-41
Parts List 42-43
Warranty Information 44

Important Safety Information
3
THANK YOU for making this Power System unit a part of your exercise pro-
gram. Keys Fitness and our Power System Series assures the very best in value,
appearance, durability and biomechanics.
This manual will guide you through the assembly process. If at any time you are
having trouble with the assembly or use of this product, then please contact us at
our Keys Fitness Help-line. We have trained service technicians on site to take
care of you, our valued customer.
REGISTRATION CARD
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register on-line at www.keysfitness.com within 10 days
of purchase.
POWER SYSTEM SERIES
QUESTIONS?
CALL
1-888-340-0482
Monday-Friday
8:30-5:30 Central Time
When calling please have the following product information available:
• Product Series
• Model #
• PO # (located on the front of the manual)
• Part Number
• Part Description

Before You Start
4
Prior to assembly, remove components from the box and verify that all the listed parts were supplied.
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
SAFETY INFORMATION WARNING!
Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with
pre-existing health problems. Keys Fitness Products LP assumes no responsibili-
ty for personal injury or property damage sustained by or through the use of this
product.
It is the owner’s responsibility to ensure that all users of this unit have read the
Owner’s Manual and are familiar with safety information and precautions.
SAFETY PRECAUTIONS
• This Power System unit should only be used on a level surface and is intended
for indoor use only. Keys Fitness recommends an equipment mat be placed
under the unit to protect the floor or carpet and for easier cleaning.
• Wear comfortable, good-quality walking or running shoes and appropriate
clothing. Do not use this unit with bare feet, sandals, socks or stockings!
• Always examine your unit before using to ensure all parts are in working order.
• Do not leave children unsupervised near or on the unit.
• Service to your Power System unit should only be performed by an authorized
service representative, unless authorized and/or instructed by a Keys Fitness
technician. Failure to follow these instructions will void the warranty.

Assembly
5
Box 1

Assembly
6
Box 2

Assembly
7
Box 3

Assembly
8
Box 4

Assembly
9
Box 5

Assembly
10
Box 6 Box 7
Box 9
Box 11
Box 8
Box 10

Assembly
11

Assembly
12

Assembly
13

Step 1
Slide two Guide Rods (24) into Rear Frame A (1) and secure using two Washers (102), two
Spring Washers (103), and two Allen Bolts (97).
Repeat to complete Rear Frame B (128) assembly.
Assembly
14
Figure 1
A
B

Assembly
15
Step 2
Attach Front Upright (86) to Seat Pad Support Receptacle (2) using two Nylon Lock Nuts (104), two
Washers (102), and two Bolts (95).
Slide Seat Pad Support Receptacle (2) onto Rear Frame A (1). Next, attach Main Rear Frame (121) to the
side of Seat Pad Support Receptacle (2). Secure the assembly in place using two Nylon Lock Nuts (104),
four Washers (102), and two Bolt (153).
Connect Pec Dec Mount (7) to Seat Pad Support Receptacle (2) using two Nylon Lock Nuts (104), two
Washers (102), and two Bolts (94). Use one Washer (107), one Spring Washer (103), and one Bolt (93) to
secure it at the top.
Attach Rear Frame B (128) to Rear Main Frame (121) using two Nylon Lock Nuts (104), two Washers
(102), and two Bolts (95).
Figure 2
A
B

Assembly
16
Step 3
Connect Main Upright A (3) to the top of Seat Pad Support Receptacle (2). Use three Washers (101), one
Spring Washers (117), one Nylon Lock Nut (105), and two Bolts (98) to secure them on the bottom. Next, use
three Nylon Lock Nuts (104), six Washers (101), and three Bolts (94) to secure the sides.
Figure 3
A

Step 4
First, slide a Weight Stack Bumper (30) down each Guide Rod (24). Next, slide weight plates down the
Guide Rods (24) in this order: five 15lb Plates (36), nine 10lb Plates (37), five 5lb Plates (38), and the Top
Plate (27). Note: Number of weight plates may vary depending on your specific configuration.
Slide Main Top Beam (4) onto Main Upright A (3) and two Guide Rods (24). Secure to Main Upright A
using two Nylon Lock Nuts (104), four Washers (101), and two Bolts (98). Next, use two Washers (102), two
Spring Washers (103), and two Bolts (97).
Assembly
17
Figure 4

Step 5
Connect Press Arm Support (5) to Main Upright A (3) by sliding Shaft (74) into the assembly. Secure the
assembly using two Screws (84).
Attach Press Arm (6) to Press Arm Support (5) by sliding Shaft (73) into the assembly. Use two Screws (84)
to secure Shaft (73) in place.
Assembly
18
Figure 5

Assembly
19
Step 6
Slide Right Pec Dec Arm (8) on to the shaft of the Pec Dec Mount (7). Secure the arm in place using
one Big Washer (76), one Washer (102), one Spring Washer (103), and one Allen Bolt (97).
Slide Pec Dec Handlebar (19) onto the top of the Right Pec Dec Arm (8) and secure using one Chrome
Washer (106), one Washer (102), one Spring Washer (103), and one Allen Bolt (97).
Repeat this step to complete the Left Pec Dec assembly.
Figure 6