KI Pirouette User manual

Assembly Instructions
Pirouette® Tables
Table-to-Table Ganging
September 2014
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Side-to-Side Ganging, 24/30”
Pirouette Nesting & Fixed-Base
Tables
Note: Take note of correct ganging
hook and peg mounting locations
to assure proper latching for each
type of installation. The instructions
on this page detail ganging of
24 & 30” wide tables side-to-side.
For 18” wide tables, see
instructions on pages 3 & 4.
1. As illustrated, and based on the
table width, position the two
ganging hooks as shown, at the
underside of the first table. Install
the two hooks to the first table
using two pegs and #14 x 11/2”
wood screws. Next, install two pegs
at the other illustrated locations for
future use to store ganging hooks
(Figure 1).
2. At the second table, install two pegs
in line with the first set of pegs
(Figure 1).
3. Move tables together and swing the
ganging hooks of the first table to
securely engage the pegs under the
second table (Figure 2).
4. When tables have been un-ganged,
simply swing the two ganging
hooks around and snap them onto
the two pegs installed for storage
(Detail A).

2
Pirouette® Tables - Table-to-Table Ganging
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Back-to-Back Ganging, 18,
24 & 30” Pirouette Nesting &
Fixed Base Tables
Note: Take note of the correct
orientation of ganging hooks and
peg mounting locations to assure
proper latching for back-to-back
ganging (Figure 3).
1. As illustrated in Figure 3, and
following instructions for ganging
hook installation on page 1,
install hooks and pegs for
back-to-back ganging of two
tables (Figures 1 & 3). Next,
install two pegs at the other
illustrated locations for future use
to store ganging hooks
(Figure 3).
2. Move tables together and swing
the ganging hooks of the first
table to securely engage the pegs
under the second table (Figure 3).
3. When tables are un-ganged,
simply swing the two ganging
hooks around and snap them
onto the two pegs installed for
storage (Detail A).

Pirouette® Tables - Table-to-Table Ganging
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
3
Side-to-Side Ganging, 18”
Wide Pirouette Nesting Tables
Note: Take note of correct
ganging hook and peg mounting
locations to assure proper
latching for side-to-side
installation. The instructions on
this page describe hook and peg
installation for ganging of 18”
wide tables side-to-side. For
24 & 30” wide tables, see page 1
instructions.
1. As illustrated, and based on the
18” table width, position the two
ganging hooks as shown, one
at the underside of the first table
and one at the underside of the
second table, at the opposite side.
Install each hook using one peg
and a #14 x 11/2” wood screw
(Figure 4).
2. Next, install three pegs at the
other illustrated locations, two for
ganging tables together and one
for use to store the ganging hook
(Figure 4).
3. Move tables together and swing
the ganging hooks of each table
around and engage the pegs of
the opposite table, ganging the
tables together (Figure 5).
4. When tables are un-ganged,
simply swing one ganging hook
around and out of the way and
the other hook around and snap it
onto the peg installed for storage
(Figure 4 & Detail A).

1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2014 Krueger International, Inc. All Rights Reserved • Code KI-62634/KI/PDF/0914
Pirouette® Tables - Table-to-Table Ganging
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Side-to-Side Ganging, 18”
Wide Pirouette Fixed-Base
Tables
Note: Take note of correct
ganging hook and peg mounting
locations to assure proper
latching for side-to-side
installation. The instructions
on this page describe hook and
peg installation for side-to-side
ganging of 18” wide
Fixed-Base Tables. For 24 & 30”
wide fixed base tables, see page 1
instructions.
1. As illustrated, and based on the
18” table width, position the two
ganging hooks as shown, one
at the underside of the first table
and one at the underside of the
second table, at the opposite
side. Install each hook using one
peg and a #14 x 11/2” wood screw
(Figure 6).
2. Next, install four pegs at the
other illustrated locations, two
for ganging tables together and
two for use to store the ganging
hooks (Figure 6).
3. Move tables together and swing
the ganging hooks of each table
around and engage the pegs of
the opposite table, ganging the
tables together (Figure 7).
4. When tables are un-ganged,
simply swing each ganging hook
around and snap it onto the peg
installed for storage (Figure 7).
Note: Back-to-Back ganging for
18” wide fixed-base tables is the
same as nesting tables. See page
2 for details.