KI All Terrain Binder Tower User manual

Assembly Instructions
All Terrain® Binder Tower
February 2014
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Caster with Outriggers Assembly
1. Locate the caster/hardware packet
that is shipped inside the binder
tower. Secure or remove any loose
components inside the tower.
2. Carefully turn storage tower on
it’s back or upside-down on a soft
protective surface.
3. Thread the casters into the
outriggers. Locking casters must
be positioned to the front of the
cabinet as illustrated. Tighten the
jamb-nut of each caster to the
bottom of the tower with a wrench
(Figure 1).
4. Gently raise the cabinet to it’s
upright position on the casters
(Figure 1).
Inboard Caster Assembly
1. Locate the caster/hardware packet
that is shipped inside the binder
tower. Secure or remove any loose
components inside the tower.
2. Carefully turn storage tower
upside-down on a soft protective
surface.
3. Thread the casters into the bottom
of the binder tower. Locking casters
must be positioned to the front of
the cabinet as illustrated. Tighten
the jamb-nut of each caster to the
bottom of the tower with a wrench
(Figure 2).
4. Gently raise the cabinet to it’s
upright position on the casters
(Figure 2).

2
All Terrain®Binder Tower
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Flush-Mount Pull Assembly
1. Locate the pull/hardware packet
that is shipped inside the binder
tower.
2. Using two 4mm x 10mm screws,
fasten the pull to the door as
illustrated (Figure 3).
3. Finish the inside of the door with
two black plastic screw caps
(Figure 3).
Note: If installing a pull on a
laminate door, use two
4mm x 25mm screws per pull.
Black caps are not required.
Landing Pad Assembly
1. The landing pad top is shipped
with two bolts securing it to the
storage unit. Remove the two
bolts and properly dispose of
them. Gently set the top aside,
assuring it will not get damaged/
scratched.
2. Locate the hardware pack for the
Landing Pad and identify the
parts by referencing Figure 4.
Begin assembly by inserting four
1/4-20 x 4” bolts into four (upper)
landing pad mount bushings.
Secure the upper bushings to
the underside of the landing pad
as illustrated using four #8 x ½”
screws (Figure 4).
3. Place a lower landing pad post
bushing into the bottom of each
landing pad post and press the
four landing pad posts/lower
bushings onto the installed upper
landing pad mount bushing and
4” bolt (Figure 4).
4. Carefully position the landing pad
with installed bushings, posts
& bolts such that the four bolts
insert through the four mounting
holes in the top of the cabinet
(Figure 4).
5. From inside the cabinet, locate
the 1/4-20 x 4” bolts inserted
through the top and place a 1/4”
flat washer and 1/4-20 k-lock nut
onto each bolt. Tighten nuts to
secure landing pad to cabinet top
(Figure 4).

All Terrain® Binder Tower
Assembly Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
3
Adjustable Shelf Assembly
1. Remove the shipping tape
securing the shelf and brackets
during shipment.
2. Hook the shelf brackets into the
slots at the inside of the cabinet
as illustrated. Make sure the
brackets are at the same height on
both sides (Figure 5).
3. Install the shelf by setting it onto
the brackets. Make sure the shelf
is pushed all the way back into the
cabinet (Figure 5).
Door Hinge Adjustment
1. For overlay adjustment, turn
eccentric screw (A). The overlay
can be reduced a maximum of
-2 mm (Figure 6).
2. For Height adjustment
(+/- 2 mm) first unscrew fixing
screw (B). Detach center stop (C)
with screwdriver, adjust the height
of the door and tighten fixing
screws (B) (Figure 6).

KI
1330 Bellevue Street
P.O. Box 8100
Green Bay, Wisconsin 54308-8100
1-800-424-2432
www.ki.com
KI is a registered trademark
of Krueger International, Inc.
© 2014 Krueger International, Inc.
All Rights Reserved
Part# 2.80485
Code KI-61328R3/KI/PDF/0214