KI Gladly Lounge Chair Guide

Repair & Replacement Instructions
Gladly™ Lounge Chair
October 2021
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Seat Cushion Replacement
1. Place chair upside down onto a soft,
protective surface (Figure 1).
2. To expose the seat screws, partially
remove the fabric veil with either a
staple puller, or cut it all away by
using a utility knife. Use a staple
puller if the veil will be stapled back
on after seat cushion replacement,
or use a utility knife if the veil will be
removed and discarded (Figure 1).
3. Using the appropriate socket size,
remove the four seat cushion hex
screws and washers (Figure 1).
4. Next, rotate the chair back onto its
legs and the seat cushion can be
lifted away from the chair (Figure 2).
5. To install the new cushion, set it
down onto the chair with the screw
holes facing the chair frame. Then,
rotate the chair back upside down
and soft protective surface (Figure 2).
6. Align the chair and cushion screw
holes and re-install the hex screws
and washers previously removed in
Figure 1.
7. If the fabric veil is to be re-installed,
stretch the fabric and use a staple
gun to do so.

2
Gladly™ Lounge Chair
Repair & Replacement Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Back Cushion Replacement
1. Using steps 1-4 on previous
page, remove the seat cushion
(Figure 1).
2. With the seat cushion removed,
the back cushion hex screws will
be revealed (Figure 1).
3. Using the appropriate socket size,
remove the two back cushion hex
screws and washers (Figure 1).
4. Next, the back cushion can be
lifted away from the chair by
pulling up vertically. There are
z-brackets on the back side of the
cushion and on the chair frame to
help keep it attached (Figure 2 &
Detail A).
5. To install the new cushion, lower
it down onto the chair with the
z-brackets facing the chair frame.
Make sure the z-brackets engage
with each other (Figure 2 &
Detail A.
6. Align the chair and cushion screw
holes and re-install the hex
screws and washers previously
removed in Figure 1.

Gladly™ Lounge Chair
Repair & Replacement Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
3
Leg Replacement
1. Place chair upside down onto a
soft, protective surface (Figure 1).
2. Using a Phillips head screw
driver, remove the four screws
holding the leg to the chair
(Figure 1).
3. Once screws are removed, leg
should lift right off (Figure 1).
4. To attach new leg, make sure it is
facing the appropriate direction
and that screw holes are aligned.
Then, install screws removed
from step one. Do not over
tighten (Figure 1).

1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2021 Krueger International, Inc. All Rights Reserved • Code KI-RR-000034/KI/PDF/1021
Gladly™ Lounge Chair
Repair & Replacement Instructions
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Press-In Glide Replacement
(metal leg only)
1. Place chair upside down onto a
soft, protective surface.
2. Using a putty knife, pry up on the
glide edge until it is free
(Figure 1).
3. Once glide its removed, press in
the new replacement glide and
lightly tap in with a rubber mallet
Figure 2).
Nail-In Glide Replacement
(wood leg only)
1. Place chair upside down onto a
soft, protective surface.
2. Using a putty knife, pry up on the
glide edge until it is free
(Figure 1).
3. Once glide its removed, center the
new replacement glide on bottom
of leg and lightly tap in with a
rubber mallet Figure 2).
Threaded Glide Replacement
(wood leg only)
1. Place chair upside down onto a
soft, protective surface.
2. Grip glide with hand and turn
counter clockwise to loosen.
Once loose, un-thread the glide
from the leg (Figure 1).
3. Once glide its removed, thread in
the new replacement glide in to
the threaded hole clockwise until
it is tight (Figure 2).