KI Intellect Chair Guide

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Repair & Replacement Instructions
Intellect® Chair
Seat Support Bracket, Seat & Back
July 2018
Note: If a powered device is used to
tighten the screws, start at the lowest
torque setting and slowly increase
the torque until the screws are snug
against the frame. Damage to the
plastic seat could result if the
screws are over-tightened.
Seat Support Bracket Installation
Note: Seat Support Brackets are
only available for EC16 & EC18
(Large and X-Large) Intellect Chairs.
1. Carefully place chair upside down on
a soft, protective surface. Locate the
two front 20mm Torx screws securing
the seat to the seat mounting plate
and remove them using a Torx T20
drive (Figure 1).
2. Position the seat support bracket
onto the seat mounting plate so the
wings of the bracket rest under the
front of the seat. Align the holes of
the bracket with the two front holes of
the mounting plate and loosley start
each of the two 20mm Torx screws
previously removed in step 1. Using
a Torx T20 drive, carefully tighten the
two 20mm Torx screws. Take care
to not over tighten or damage may
occur to the plastic seat (Figure 2).
Figure 1
20mm
Torx screw
seat mounting
plate
Figure 2
seat support
bracket
20mm Torx
screw
seat mounting
plate

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Intellect® Chair
Assembly Instructions
Seat Removal & Replacement
1. To remove the seat, carefully place
chair upside down on a soft,
protective surface. Locate the four
20mm Torx screws and remove
using a Torx T20 drive (Figure 3).
2. To install a replacement seat, first
position the seat onto the seat
mounting plate. Align the holes
of the seat with the mounting
plate holes and loosely start each
of the four 20mm Torx screws.
Using a Torx T20 drive, carefully
tighten each of the four screws.
Take care to not over tighten or
damage may occur to the plastic
seat (Figure 3).
Back Removal & Replacement
1. To remove the back, first locate
the four 35mm Torx screws which
are recessed into the back of the
handle. Remove the screws with a
Torx T20 drive (Figure 4).
2. To install a replacement back,
first position the back onto the
handle. Align the holes of the
back with the holes on the handle
and loosely start each of the four
35mm Torx screws. Using a Torx
T20 drive, carefully tighten each
of the four screws. Take care to
not over tighten or damage may
occur to the plastic back
(Figure 4).
General Maintenance
Note: Intellect seats, backs and
desktops are one-piece injection
molded ABS. The surfaces may
be cleaned with most common
cleaners and a rag or soft brush.
Avoid using any solvent-based
cleaners as they can react with the
ABS and degrade the appearance
and strength of the product.
Figure 3
seat
20mm
Torx screw
Figure 4
35mm Torx
screw
back
handle
1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2018 Krueger International, Inc. All Rights Reserved • Code KI-RR-000016/KI/PDF/0718