Kimball Office Footprint Xsite User manual

Systems Assembly Instructions
Footprint®
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1741505 Revision A-04
Page 1 of 3
Lunar Overhead Storage
Cabinet Ganging Bracket
for Xsite®/Traxx®
Tools Required
■Electric Drill/Driver ■Rubber (non-marring) Mallet
■#3 Phillips Head Bits
Package Contents
■1 Ganging Bracket ■2 #10 x ¹⁄₂" Self-drilling
Phillips Panhead Screws
Installation
Note: This instruction covers installation of ganging brackets
for all Lunar cabinetry assembled and installed on Xsite and
Traxx only. All operations to assemble the cabinet and doors
can be done by one person, but it is recommended that two
people install the units to the panel system/Traxx.
Important: This instruction explains basic Lunar ganging
bracket assembly techniques. Please see assembly instruction
“Lunar Overhead Storage, Flipper Door Cabinet” for basic
cabinetry assembly and installation to panel systems as
needed.
Purposes of the ganging bracket:
■To align the front lower edge of the adjacent cabinet.
■To add rigidity to the installed cabinets.
Figure A
Figure B
Pre-installation action: As mentioned above, reference
assembly instruction “Lunar Overhead Storage, Flipper Door
Cabinet” to assemble all cabinetry and install it to Xsite panels
and/or Traxx. Take care to not damage the unit(s) or the
panel. Inventory the package contents before proceeding with
assembly/installation. Stop if there are insufficient items to
complete the assembly.
1. Figure A shows a single door Lunar overhead cabinet for
reference.
2. Figure B shows a typical side-by-side application for
ganging on an Xsite panel run.

Systems Assembly Instructions
Footprint
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1741505 Revision A-04
Page 2 of 3
Installation (continued)
3. Position the cabinets in their leveled and desired location.
To slide cabinets right or left, lift the lower front edge of
each cabinet, thus lifting the cabinet away from the panel
face(s). Open the cabinet doors and fully slide them back.
Press the adjacent cabinets together by pushing horizontally
and slightly lifting the front edge of each cabinet. The
cabinet ends must be in direct contact with no gaps.
(Figure C).
4. Continue pushing and slightly lifting the cabinets. Loosely
position the ganging bracket under the lower front flanges
of the cabinet so that the vertical “ears” of the ganging
bracket are directly behind the edge of the lower front shelf
flange. (Figure D).
5. With the ganging bracket in position, press the bracket
upward to its final fully-seated position. Significant pressure
will be required as the bracket “ears” are intended to
grip the interior end panels of the cabinet, aiding in
positioning/holding power of the assembly. A rubber
non-marring mallet may be needed to fully seat the bracket.
(Figure E).
Figure C
Figure D
Figure E
Ganging bracket “ears”
engage both cabinets
Cabinets must be
in direct contact
with no gaps
Ganging bracket
pressed into position

Systems Assembly Instructions
Footprint
Printed in U.S.A. © 2004 Kimball International, Inc. T 800.482.1818 F 812.482.8300
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part No. 1741505 Revision A-04
Page 3 of 3
Installation (continued)
6. Continue pushing and slightly lifting the cabinets. Install the
self-drilling screws into either of the holes, one per side, in
the lower flange of the ganging bracket, drilling directly into
the lower flange of the cabinet shelf. Two holes per side are
provided in case the initial attempt at screw installation fails
and will allow a second try without having to field drill the
ganging bracket. To obtain the best grip, angle each screw
outward from the center of the bracket, which positions
each screw to the most outward edge of its hole in the
bracket. This forces the edge of the bracket hole to be in
direct contact with the screw thread as it is engaged, thus
not allowing slippage. (Figure F).
7. After all screws are firmly installed, lower cabinets down to
their normal position. Re-check that the front, lower edges
of the cabinet end panels are in alignment and are in direct
contact with no gaps. (Figure G).
8. Close cabinet doors. Per previous assembly/installation
instructions, re-check all door and lock operation.
Figure F
Figure G
Angle self-drilling
screws outward
Re-check for
alignment and
no gaps