Kimball Office Xsede Height Adjustable User manual

Xsede™ Height Adjustable 1
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2918187, Revision A
Assembly Instructions
Tools Required
 Box Cutter/Utility Knife
 Cordless Drill (optional; for M4 Allen drive ONLY)
 (2) M4 Allen wrench key/drive (1 provided in bench box)
Hardware Required
1 - Center Screen (accessory rail mount)
4 - M6-1 X 12 Button Head Cap Machine Screws
4 - M6 Rhombus Nuts
4 - M8-1.25 X 8MM Set Screws
2 - End Caps
1 - Bench Base (ordered separate)
Installation
Note: Center Screens should be installed after bases/tops.
1. Using a knife, open box removing center screen w/brackets
and parts bag. See Figure A.
2. Push button head screws through holes on brackets and
thread rhombus nuts onto button head screws on the bottom
side of bracket. See Figure B. Note: Thread rhombus nuts
just enough they hold onto button head screws. Over
threading won’t allow the rhombus nuts to turn in ex-
trusion. See Step 4.
3. Slide screen in-between bench base/work surfaces and set
screen gently on aluminum accessory rail. The edge of
screen and edge of work surface will set flush to each other.
Use a straight edge if need be for keeping work surfaces
and screens aligned. See Figure C, Note: check rhombus
nuts are oriented as shown in Figure B correctly before
completing this step. This is to make sure screen drops
into accessory rail.
4. Tighten button head screws into rhombus nuts using M4
Allen wrench drive. Rhombus nuts will turn as you tighten
button head screws.
5. Sight down side view of base and check for alignment of
screen to screen requirements. If screens are leaning a cer-
tain way, see next step. If not, skip to step 10. See Figure D.
6. If screens are setting at an angle, loosen connector bolts and
nuts holding brackets and screen together using (2) M4
Allen wrench key/drives. See Figure E.
Figure A
Figure B
Nut
Orientation
(Bottom View)
Fastener
Attachment
Fastener
Threading
Figure C
SLIDE IN
BETWEEN
AND SET ON
RAIL
SIDE VIEW
EXTRUSION
FLUSH
EDGES
Figure E
Figure D SCREEN 1
SCREEN 2
SCREEN 3
SIDE
VIEW
LOOSEN
CONNECTOR
BOLT & NUT;
BOTH SIDES
OF SCREEN
Xsede Fixed Center Screen
Accessory Rail Mount

Xsede™ Height Adjustable 2
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2918187, Revision A
Assembly Instructions
Figure F
Figure H
END CAP
7. Once connector bolt/nut are loosened, locate M8 set screws
underneath channel of screen bracket on both sides. See
Figure F for set screw location. Follow Figure G for
alignment. If scr een is leaning to the r ight, tighten set
screws on opposite side of bracket. If screen is leaning to
the left, tighten set screws on opposite side of bracket. To
loosen and tighten set screws, use M4 Allen wrench key
provided in bench base parts box.
8. Sight down screens one last time before proceeding to next
step.
9. Once screen alignment is set, tighten connector bolts and
nuts together using (2) M4 Allen drive/keys.
10. Remove Tesa tape and end caps from parts bag. Apply tape
to inside of end cap and place over aluminum extrusion at
the end of each row as shown in Figure C. Press end cap to
ensure tape is adhered to aluminum extrusion.
M8 Set
Screw
Figure G
SCREEN TILTING RIGHT
(TIGHTEN LOOSEN SET
SCREWS ON OPPOSITE
SIDE)
CONNECTOR
BOLT (LOOSEN;
M4 ALLEN KEY)
CONNECTOR
BOLT (LOOSEN;
M4 ALLEN KEY)
CONNECTOR
NUT (LOOSEN;
M4 ALLEN KEY)
CONNECTOR
NUT (LOOSEN;
M4 ALLEN KEY)
SCREEN TILTING LEFT
(TIGHTEN LOOSEN SET
SCREWS ON OPPOSITE
SIDE)

Xsede™ Height Adjustable 3
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2918187, Revision A
Assembly Instructions
Tools Required
 Box Cutter/Utility Knife
 Cordless Drill w/#3 Phillips head bit drive
 (2) M4 Allen wrench key/drive
 7/16” socket/wrench
Hardware Required
1 - Center Screen (cross rail mount)
8 - 1/4-20 X 3” Pan head Phillips machine screw
8 - 1/4-20 Hex nuts
1 - Bench Base (ordered separate)
Installation
Note: Center Screens should be installed after bases/tops.
1. Using a knife, open box removing center screen w/brackets
and parts bag. See Figure A.
2. Slide screen in-between bench base/work surfaces and set
on top of crossrails over 4 slots. The edge of screen and
edge of work surface will set flush to each other. Use a
straight edge if need be for keeping work surfaces and
screens aligned. See Figure B.
3. To attach brackets to crossrails, push (8) 1/4-20 X 3” bolts
through top of bracket holes into crossrail slots. Thread
(8) 1/4-20 hex nuts on bottom side of crossrail onto 1/4-20
bolts to secure brackets. Tighten using cordless drill and #3
Phillips drive. See Figure C.
4. Sight down side view of base and check alignment of
screen to screen requirements. If screens are leaning a cer-
tain way, see next step. See Figure D.
5. If screens are setting at an angle, loosen connector bolts
and nuts holding brackets and screen together using (2) M4
Allen wrench key/drives. See Figure E.
Figure A
Figure B
SLIDE IN
BETWEEN
AND SET ON
CROSSRAIL
FLUSH
EDGES
Figure C
Fastener
Attachment
Figure D SCREEN 1
SCREEN 2
SCREEN 3
SIDE
VIEW
Figure E
LOOSEN
CONNECTOR
BOLT & NUT;
BOTH SIDES
OF SCREEN
Xsede Fixed Center Screen
Cross Rail Mount

Xsede™ Height Adjustable 4
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2918187, Revision A
Assembly Instructions
7. Once connector bolt/nut are loosened, locate M8 set screws
underneath channel of screen bracket on both sides. See
Figure F for set screw location. Follow Figure G for
alignment. If screen is leaning to the r ight, tighten set
screws on opposite side of bracket. If screen is leaning to
the left, tighten set screws on opposite side of bracket. To
loosen and tighten set screws, use M4 Allen wrench key
provided in bench base.
8. Sight down screens one last time before proceeding to next
step.
9. Once screen alignment is set, tighten connector bolts and
nuts together using (2) M4 Allen drive/keys.
Figure F
M8 Set
Screw
Figure G
SCREEN TILTING RIGHT
(TIGHTEN LOOSEN SET
SCREWS ON OPPOSITE
SIDE)
CONNECTOR
BOLT (LOOSEN;
M4 ALLEN KEY)
CONNECTOR
BOLT (LOOSEN;
M4 ALLEN KEY)
CONNECTOR
NUT (LOOSEN;
M4 ALLEN KEY)
CONNECTOR
NUT (LOOSEN;
M4 ALLEN KEY)
SCREEN TILTING LEFT
(TIGHTEN LOOSEN SET
SCREWS ON OPPOSITE
SIDE)

Xsede™ Height Adjustable 5
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2918187, Revision A
Assembly Instructions
Xsede Privacy Screen
Assembly
Tools Required
 Box Cutter/Utility Knife
 Cordless Drill w/#2 Phillips head bit drive
Hardware Required
1 - Privacy Screen (Full/Privacy Screen)
2 - Privacy Screen Brackets
8 - 1/4-20 X 3/4” Pan Head Phillips Wood Screws
2 - 1/4-20 X 1/2” Pan Head Phillips Machine Screws (used for
screen alignment)
8 - Screen Spacers 1/4” Thick
1 - Bench Base - or - (ordered separate)
1 - Freestanding Single Base - or - (ordered separate)
1 - Freestanding L-Base - (ordered separate)
Installation
Note: Privacy Screens should be installed after bases/tops.
1. Using a knife, open box removing screen, brackets, and
parts bag. See Figure A.
2. Lay screen on a non-marring surface for assembly.
3. Slide screen spacers over threaded inserts. Place screen
brackets over (4) holes positioning as such shown in Figure
B. Attach using drill w/#2 Phillips dr ive 1/4-20 X 3/4”
machine screws through spacers into inserts. Note: Don’t
over tighten or threaded inserts might pull out of core.
4. When assembling screen to L-base or Single base, there is a
range to mount screen either flush to top - or maximum 1”
wire gap. This is to ensure table stability. Don’t exceed 1”
gap between surface and screen. See Figure D for
mounting options.
5. When attaching screens to bench base, there *MUST* be a
1” gap in between screens for prevention of pinched fingers
when screens raise and lower. See Figure D.
6. To attach privacy screens, the edge of screen and edge of
work surface will set flush to each other as shown in Figure
C, left picture. Full privacy screen will be attached cen-
tered inside worksurface with 6” offset each side, Figure C,
right picture. For scr een attachments, using dr ill w/#2
Phillips drive, attach all #8 X 3/4” wood screws, 4 for each
bracket to worksurface.
Figure A
Figure B
Figure C
PRIVACY
SCREEN
FULL
PRIVACY
SCREEN
Figure D
1" MINIMUM
1" MAXIMUM
WIRE
GAP
1" MAXIMUM
ALL AROUND
WIRE
GAP
(8) 1/4 X 3/4”
Machine
Screws
PRIVACY SCREEN MOUNTS Figure D FULL PRIVACY
MOUNT
1" MAXIMUM
WIRE
GAP
FLUSH
Privacy
Screen
6" OFFSET
EACH SIDE
Full-
Privacy
Screen
SCREEN
BRACKET
(8) Screen
Spacers
(between
bracket and
wood core)

Xsede™ Height Adjustable 6
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call Kimball Office Customer Care.
Part 2918187, Revision A
Assembly Instructions
Installation (cont.)
7. After screens have been attached, sight down side view for
required alignment of screen to screen. See Figure E.
8. To align screens vertically, locate the 1/4-20 X 1/2” pan
head machine screw in parts bag. Thread screw into screen
brackets on both sides until tension is felt. This will indi-
cate screw is flush with the bottom of the work surface.
9. Screen leaning in: use #2 Phillips bit drive and unscrew
back wood screws and tighten 1/4-20 X 1/2” Phillips ma-
chine screw until desired vertical position is obtained.
10. Screen leaning out: use #2 Phillips bit drive and unscrew
front wood screws. Tighten 1/4-20 X 1/2” Phillips machine
screw until desired vertical position is obtained.
11. Screw #8 X 3/4” wood screws back into work surface using
#2 Phillips bit drive. Note: Don’t over tighten to prevent
screen from pulling out of alignment.
Figure E
Figure F
SIDE
VIEW
SCREENS
MIS-ALIGNED
(Leaning In)
1/4-20 X 1/2”
Pan Head
Machine Screw
FRONT
WOOD
SCREWS
BACK
WOOD
SCREWS