kingsley-bate LO61/64 User manual

ASSEMBLY INSTRUCTIONS FOR THE LO61/64
LEGS SEAT FRAME
PLUGS CONNECTOR HARDWARE
CENTER LEG SUPPORT
CUSHION
STEP-I
Unpack, inspect and lay the parts on a clean, flat, soft surface to avoid marring the
Wood.
NOTE: During assembly of the furniture please match joints with the corresponding
letters or numbers stamped on wood.
SEAT CUSHION
UPHOLSTERED BACKREST
BACK CUSHION
M6 X 50mm
M6 X 20mm
BOLT HEX M8 X 80mm
SPLIT & FLAT WASHER
ALLEN KEY 4mm WRENCH

STEP-II
Carefully lay the SEAT FRAME upside down on your clean surface, insert and attach the legs
as shown in the assembly photographs using the M6 x 50mm bolts provided. You may need
to wiggle the legs as you finish tightening the bolts to make sure they are fully secured.
NOTE: DO NOT USE POWER TOOLS AS IT MAY DAMAGE THE ITEM.
STEP-III
With the SEAT FRAME upside down, set the center leg support on the frame as shown in
the photographs, ensuring that the holes in the SEAT FRAME and the leg supports are
aligned.
Insert one each of the four M6 x 20mm Bolts into each hole. Bolts should be initially
threaded by hand to prevent cross-threading.
NOTE: Do not tighten the bolts until all have been partially threaded. Once all bolts are in
place, use the provided Allen Key to tighten them securely. Be careful not to overtighten, as
this can cause the threads to strip. NEVER USE A POWER TOOL TO TIGHTEN THE
BOLTS.
The center leg supports include levelers for applications where the SEAT FRAME is used on
an uneven surface. The height of the levelers can be adjusted by turning them. The levelers
are properly adjusted when they are touching the ground.

STEP-IV
Requires two people. With the assistance of a second person, lift the SEAT FRAME up,
rotate it in the air and set it gently back on the ground.
Locate the six holes on the underside of the UPHOLDSTERED BACKREST and take note
of the position of the corresponding holes on the SEAT FRAME. Set the
UPHOLDSTERED BACKREST on the SEAT FRAME as shown in the photographs,
ensuring that the holes in the UPHOLDSTERED BACKREST and SEAT FRAME are
aligned.
Locate the six holes on the underside of the SEAT FRAME that correspond with the holes in
the UPHOLDSTERED BACKREST and insert one each of the M8 x 80mm Hex Bolts, Split
Washers, and Flat Washers into each hole (see picture showing correct arrangement of
washers). Bolts should be initially threaded by hand to prevent cross-threading.
NOTE: DO NOT TIGHTEN THE BOLTS UNTIL ALL HAVE BEEN PARTIALLY
THREADED. ONCE ALL BOLTS ARE IN PLACE, USE THE WRENCH PROVIDED TO
TIGHTEN THEM SECURELY. BE CAREFUL NOT TO OVERTIGHTEN, AS THIS
CAN CAUSE THE THREADS TO STRIP. NEVER USE A POWER TOOL TO TIGHTEN
THE BOLTS.
STEP-V
If you are connecting multiple sectional items together the photographs below illustrate
where to attach them. DO NOT ATTACH THEM WHILE ITEM IS UPSIDE DOWN AS
YOU WILL NOT BE ABLE TO UPRIGHT THE ASSEMBLY.

Plugs are provided to fill any unused holes in the metal frame that may be visible between
the slats of the table section.
Locate any unused holes in the metal frame that are visible from above. From the underside
of the frame, insert a plug upward into the hole as shown in the photographs.
The plugs are designed to fit snugly, and it may be necessary to use a rubber mallet, to press
them into place.
NOTE: Do not use a hammer to drive the plugs into place, as doing so may cause damage to
the frame or the plug.
IF YOU HAVE ANY QUESTIONS REGARDING THE ASSEMBLY OF YOUR
KINGSLEY BATE FURNITURE, PLEASE CONTACT KINGSLEY BATE CUSTOMER
SERVICE AT 703-361-7000. WE THANK YOU FOR CHOOSING OUR FURNITURE.
* KINGSLEY BATE WILL NOT TAKE RESPONSIBILITY FOR DAMAGE
IF THESE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY
7200 Gateway Court, Manassas, Virginia 20109
Phone: [phone], Fax: [phone]