KLS Martin CEMOR User manual

English
CEMO
R Monitor Suspension System
Mo
unting Instructions
90-040-72-10
Revision 1
Date of Release: 2016-12

2 Revision 1
Symbol Explanation
Safety alert symbol
CAUTION Indicates a situation which, if not avoided, could result
in minor or moderate injury.
WARNING Indicates a situation which, if not avoided, could result
in death or serious injury.
DANGER Indicates a situation which, if not avoided, will result in
death or serious injury.
Follow Instructions for Use
Reference number for ordering Gebrüder Martin products (item
number)
Serial number
Manufacturing date
Manufacturer
Warning: dangerous electric voltage
Falling parts
Warns against falling parts when standing under the suspension
arm system while assembly/disassembly work is being performed.
Danger of crushing
Warns against trapping limbs during assembly/disassembly work.
Danger of collisions
Warns against collisions with components of the suspension arm
system during assembly/disassembly work.
Tightening torque
Warns against falling down of the suspension arm system due to
insufficiently tightened fastening screws.
Information on minimum and maximum temperature for storage
and transportation.
See section 19.2 “Technical Data”, page 77.

Revision 1 3
Information on minimum and maximum atmospheric pressure for
storage and transportation.
See section 19.2 “Technical Data”, page 77.
Information on minimum and maximum atmospheric humidity for
storage and transportation.
See section 19.2 “Technical Data”, page 77.
Do not exceed the maximum load-bearing capacity or payload:
Warns against sudden falling due to exceedance of the maximum
load-bearing capacity or loading capacity (payload).
The maximum value is specified in kg or Nm.
CE marking of conformity
This symbol describes the product as being a component approved
by a “Nationally Recognized Testing Laboratory”, fulfilling both the
Canadian and USA deviations from the applicable standards.
This product may not be disposed of as normal household garbage,
see section 22.2 “Disposal of the Device”, page 82

Mounting Instructions
0BCEMOR Monitor Suspension System
4 Revision 1
Contents
Terms & Acronyms.................................................................................. 8
1Product Liability and Warranty ...................................................... 8
1.1 General Information..............................................................................8
1.2 Scope of Delivery..................................................................................9
1.2.1 Overview and Scope of Delivery for CEMOR 4, 6, 8.............................................. 9
1.2.2 Overview and Scope of Delivery for CEMOR LS...................................................11
1.2.3 Scope of Delivery for the optional VESA Brackets ...............................................13
1.3 Intended Purpose................................................................................15
1.3.1 Configuration and Inspection Before Mounting CEMOR ........................................15
1.3.2 Improper Use ................................................................................................16
1.3.3 Contraindications ...........................................................................................16
1.4 Warranty ...........................................................................................16
1.5 User’s Inspection ................................................................................17
1.6 Hotline...............................................................................................17
2Notices Concerning this Document................................................18
2.1 Validity of this Document.....................................................................18
2.2 Applicable Mounting Instructions...........................................................19
2.3 Symbols Used in this Document............................................................20
3Instructions for Safe Installation ..................................................21
3.1 Information on Device Identification......................................................21
3.2 Required Installation Equipment ...........................................................21
3.3 Requirements.....................................................................................21
3.3.1 Requirements for the Qualifications of the Service Technician ..............................21
3.3.2 Requirements before Installation......................................................................21
3.3.3 Assembly Process...........................................................................................22
3.3.4 Unauthorized Modifications or Adjustments........................................................22
3.3.5 Qualified Medical Staff ....................................................................................22
3.4 Notes for Operators.............................................................................23
3.5 Standards and Guidelines.....................................................................23
3.6 Combination with Products by Other Manufacturers.................................23
3.7 Patient Environment............................................................................24
4Safety Notes..............................................................................25
4.1 Information on the Rating Plate ............................................................25
4.2 The Most Important Safety Information at a Glance ................................26
4.2.1 Operation......................................................................................................26
4.2.2 Assembly/Disassembly....................................................................................27
4.2.3 Maintenance Work..........................................................................................28

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 5
5Commissioning ..........................................................................29
5.1 Initial Commissioning and Handover......................................................29
6Combination of CEMOR and Suspension Arm System......................30
6.1 Example: Checking CEMOR and the Suspension Arm System....................31
7Mounting CEMOR to the Console Tube...........................................32
7.1 Overview of the Components in this Section...........................................32
7.2 Mounting CEMOR to the Console Tube ...................................................33
7.2.1 Disassembling the Cover Panel.........................................................................33
7.2.2 Positioning CEMOR under the Console Tube.......................................................34
7.2.3 Mounting CEMOR to the Console Tube...............................................................35
8Reading and Checking the Approved Maximum Load-Bearing
capacity (Payload)......................................................................36
8.1 Overview ...........................................................................................36
8.2 Checking the Maximum Load-Bearing Capacity (Payload) on CEMOR .........36
9Adjusting the Handles on the Bottom/Rear or the Side....................38
10 Mounting Recommendations for VESA Brackets..............................39
10.1 Overview ...........................................................................................39
10.2 Attaching the Individual VESA Mounts ...................................................40
10.2.1 CEMOR 4.......................................................................................................41
10.2.2 CEMOR 6, 8...................................................................................................41
11 Installing the TFT Screens Using 1D VESA Mounts ..........................42
11.1 Overview ...........................................................................................42
11.2 Adjustment Options.............................................................................42
11.3 Preparing the Installation.....................................................................43
11.4 Mounting the TFT Screen on the VESA Mount .........................................43
11.5 Aligning and Securing the TFT Screens ..................................................45
12 Installing the TFT Screens Using 2D VESA Mounts ..........................46
12.1 Overview ...........................................................................................46
12.2 Adjustment Options.............................................................................47
12.3 Preparing the Installation.....................................................................47
12.4 Mounting the TFT Screen on the VESA Mount .........................................48
12.5 Aligning and Securing the TFT Screens ..................................................49
13 Installing the TFT Screens Using 3D VESA Mounts ..........................50
13.1 Overview ...........................................................................................50
13.2 Adjustment Options.............................................................................50
13.3 Preparing the Installation.....................................................................51

Mounting Instructions
0BCEMOR Monitor Suspension System
6 Revision 1
13.4 Mounting the TFT Screen on the VESA Mount .........................................51
13.5 Aligning and Securing the TFT Screens ..................................................53
14 Mounting Recommendations for VESA Brackets on CEMOR LS..........54
14.1 Overview ...........................................................................................54
14.2 Mounting Recommendations for VESA Brackets for Large Screens LS ........55
14.3 Mounting Recommendations for VESA Brackets Rear...............................56
15 Mounting the TFT Screen LS Using the VESA Mount for Large
Screens.....................................................................................57
15.1 Overview ...........................................................................................57
15.2 Adjustment Options.............................................................................58
15.3 Preparing the Installation.....................................................................58
15.4 Mounting the TFT Screen on the VESA Mount .........................................59
15.5 Aligning and Securing the TFT Screens ..................................................60
16 Installing the TFT Screens Using the VESA Mount Rear....................61
16.1 Overview ...........................................................................................61
16.2 Adjustment Options.............................................................................61
16.3 Preparing the Installation.....................................................................62
16.4 Mounting the TFT Screen on the VESA Mount .........................................62
16.5 Aligning and Securing the TFT Screens ..................................................64
17 Mounting the Earthing Conductor on the VESA Mount .....................65
17.1 Earthing 2D VESA Mounts and 3D VESA Mounts......................................65
17.2 Earthing the 1D VESA Mount, 1D VESA Mount Cockpit View and VESA
Mount Rear ........................................................................................66
17.3 Earthing the VESA Mount for Large Screens ...........................................67
18 Installing the Cables...................................................................68
18.1 Safety Notes ......................................................................................68
18.2 Connecting the Power Supply ...............................................................69
18.2.1 Connecting the CEMOR Power Supply Cables Provided by the Customer................69
18.2.2 Connecting the Power Supply Cables of the TFT Screens .....................................69
18.3 Connecting the Data Cables to the TFT Screens ......................................70
18.4 Connecting the Control Cables..............................................................71
19 Technical Specification................................................................72
19.1 Dimensional Drawings .........................................................................72
19.1.1 CEMOR 4.......................................................................................................72
19.1.2 CEMOR 6.......................................................................................................73
19.1.3 CEMOR 8.......................................................................................................74
19.1.4 CEMOR LS .....................................................................................................75
19.1.5 CEMOR on the Suspension Arm System ............................................................76

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 7
19.2 Technical Data....................................................................................77
19.2.1 General Technical Data ...................................................................................78
20 Permissible Third-Party Adaptions ................................................79
21 Inspection Plan ..........................................................................80
22 Ecological Information ................................................................82
22.1 Disposal of Packing .............................................................................82
22.2Disposal of the Device .........................................................................82

Mounting Instructions
0BCEMOR Monitor Suspension System
8 Revision 1
Terms & Acronyms
Designation Description
Adaption A possible combination with products from other manufacturers
BrakeGuide A colored LED lamp optically indicates the bearing point at which a brake has
been released
End device E.g. TFT monitor or medical device on the adaption
MOOP Means of Operator Protection
MOPP Means of Patient Protection
NRTL Nationally Recognized Testing Laboratory
RF Radio Frequency
VESA Video Electronics Standards Association
1Product Liability and Warranty
1.1 General Information
We thank you for having decided to buy one of our products. This product bears the CE-
marking, which means that it satisfies the essential requirements laid down in the EC Directive
concerning medical devices.
We are the manufacturer of this product:
Gebrüder Martin GmbH & Co. KG
A company of the KLS Martin Group
KLS Martin Platz 1 · D-78532 Tuttlingen · Germany
Postfach 60 · D-78501 Tuttlingen · Germany
Tel. [phone] · Fax [phone]
[e-mail] · www.klsmartin.com

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 9
1.2 Scope of Delivery
1.2.1 Overview and Scope of Delivery for CEMOR 4, 6, 8
Fig. 1-1: Scope of delivery for CEMOR 8
The figure shows the example of CEMOR 8. The scope of delivery varies depending on the
optional equipment.

Mounting Instructions
0BCEMOR Monitor Suspension System
10 Revision 1
CEMOR 4, 6, 8 with double row rail
For mounting instructions see section 6 “Combination of CEMOR and Suspension Arm
System”, page 30 and section 7 “Mounting CEMOR to the Console Tube”, page 32.
Pre-assembled double row rail
Pre-assembled optional rail extension
Pre-assembled optional handle bottom/rear with optional control buttons
For adjustment work see section 9 “Adjusting the Handles on the Bottom/Rear or the
Side”, page 38.
Pre-assembled optional handles at the sides with optional control buttons
For adjustment work see section 9 “Adjusting the Handles on the Bottom/Rear or the
Side”, page 38.
,,VESA bracket
For available versions see section 1.2.3 “Scope of Delivery for the optional VESA Brackets”
,
page 13.
Configuration Examples
Fig. 1-2: Configuration examples

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 11
1.2.2 Overview and Scope of Delivery for CEMOR LS
Fig. 1-3: Scope of delivery for CEMOR LS
The scope of delivery varies depending on the optional equipment.
CEMOR LS with double row rail
For mounting instructions see section 6 “Combination of CEMOR and Suspension Arm
System”, page 30 and section 7 “Mounting CEMOR to the Console Tube”, page 32.
Pre-assembled rails
Pre-assembled optional handle bottom/rear with optional control buttons
For adjustment work see section 9 “Adjusting the Handles on the Bottom/Rear or the
Side”, page 38.
Pre-assembled optional handles at the sides with optional control buttons
For adjustment work see section 9 “Adjusting the Handles on the Bottom/Rear or the
Side”, page 38.
,VESA bracket
For available versions see section 1.2.3 “Scope of Delivery for the optional VESA Brackets”
,
page 13.

Mounting Instructions
0BCEMOR Monitor Suspension System
12 Revision 1
Configuration Example
Fig. 1-4: Configuration example

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 13
1.2.3 Scope of Delivery for the optional VESA Brackets
Scope of Delivery for CEMOR 4, 6, 8
Fig. 1-5: Scope of delivery for VESA brackets for CEMOR 4, 6, 8
1D VESA bracket, 1D VESA bracket Cockpit View (depending on the number of flat screens)
For mounting instructions see section 10 “Mounting Recommendations for VESA Brackets”,
page 39 and section 11 “Installing the TFT Screens Using 1D VESA Mounts”, page 42.
2D VESA bracket (depending on the number of flat screens)
For mounting instructions see section 10 “Mounting Recommendations for VESA Brackets”,
page 39 and section 12 “Installing the TFT Screens Using 2D VESA Mounts”, page 46.
3D VESA bracket (depending on the number of flat screens)
For mounting instructions see section 10 “Mounting Recommendations for VESA Brackets”,
page 39 and section 13 “Installing the TFT Screens Using 3D VESA Mounts”, page 50.
Fixing elements included in the scope of delivery
•4 Allen cylinder screws M4 x 20 mm DIN 912
•4 contact washers D4,1

Mounting Instructions
0BCEMOR Monitor Suspension System
14 Revision 1
Scope of Delivery for CEMOR LS
Fig. 1-6: Scope of delivery for VESA bracket for CEMOR LS
2 VESA brackets for large screens
For mounting instructions see section 14 “Mounting Recommendations for VESA Brackets on
CEMOR LS”, page 54 and section 15 “Mounting the TFT Screen LS Using the VESA Mount for
Large Screens”, page 57.
VESA bracket rear
For mounting instructions see section 14 “Mounting Recommendations for VESA Brackets on
CEMOR LS”, page 54 and section 16 “Installing the TFT Screens Using the VESA Mount”,
page 61.
Fixing elements included in the scope of delivery
−4 countersunk screws M4 x 20 mm DIN 7991
The fixing elements for CEMOR LS are not included in the scope of delivery

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 15
1.3 Intended Purpose
•The CEMOR monitor suspension system is individually equipped. Depending on the version
and equipment, it can be used for the following:
—carrying flat screens labelled with a CE mark in OR or intensive care rooms and
medical environments
—transport and withdrawal of media such as medical gases, vacuum and compressed air,
electricity and data (e.g. telephone, nurse call, computer data, etc.).
•CEMOR can be mounted to the suspension arm systems IDP 101 S or IDP 101 S XL.
•CEMOR is suitable for continuous operation.
•The suspension arm system may be operated only by qualified medical staff with
appropriate qualifications.
•The suspension arm system may be cleaned and disinfected only by instructed hygiene
specialists.
•The suspension arm system may be serviced only by the operator’s technical specialists on
the basis of the applicable instructions.
The operator may operate the device only if an on-site functional test has previously been
performed by Gebrüder Martin or a person authorized by Gebrüder Martin. In addition, a
responsible person designated by the operator must have been instructed in the proper
handling, application and operation of the device, as well as in its permissible combination with
other medical devices, objects and accessories. This duly instructed officer shall subsequently
be responsible for familiarizing the operator’s staff with the device as the need arises.
We recommend documenting all user instructions in a medical device logbook. A copy of the
logbook is available from Gebrüder Martin.
The operational safety of the device must be verified at regular intervals, see section 21
“Inspection Plan”, page 80.
1.3.1 Configuration and Inspection Before Mounting CEMOR
The CEMOR monitor suspension system can be mounted to the suspension arm systems
IDP 101 S and IDP 101 S XL. The total weight of CEMOR, VESA brackets, flat screens and
other components must not exceed the maximum payload indicated on the rating plate, see
section 4.1 “Information on the Rating Plate”, page 25.

Mounting Instructions
0BCEMOR Monitor Suspension System
16 Revision 1
1.3.2 Improper Use
The CEMOR is configured depending on the customer's specific requirements. The dead weight
of the individual configuration and the maximum permissible load-bearing capacity (payload)
are indicated on the rating plate, see section 4.1 “Information on the Rating Plate”, page 25.
CEMOR and its optional components must not be loaded beyond their maximum load-bearing
capacity, section 19.2 “Technical Data”, page 77.
Independently of the maximum load-bearing capacity (payload) the optional components may
only be loaded with the maximum weight, see section 20 “Permissible Third-Party Adaptions”,
page 79.
Activation time of the electromagnetic brakes
The maximum switch-on time of the electromagnetic brakes of the suspension arm system
must not exceed 1 min:
•If the electromagnetic brakes are actuated for more than 1 min, the power supply unit
may switch off automatically to prevent overheating.
•If the power supply unit has switched off, then it must cool down for 10 min before it can
be switched on again, and must then be disconnected from the building’s power supply for
10 s. Only then can the standard operation of the system be continued. The maximum
switch-on time must not be exceeded, as this could result in safety shut-downs.
1.3.3 Contraindications
CEMOR must not be used in the proximity of strong magnetic fields.
No applied parts of type BF or CF in accordance with IEC 60601-1 may be directly connected to
CEMOR.
1.4 Warranty
Our Standard Terms and Conditions of Sale effective at the time shall apply. Agreements
diverging from these Standard Terms and Conditions do not restrict the legal rights of the
buyer.
Any warranty exceeding the above provisions shall require a contractual form and shall exclude
component-related vandalism, software updates and consumables.
Important Notices
The product may only be repaired by Gebrüder Martin or a qualified person or firm expressly
authorized by Gebrüder Martin to perform such work.
If the repair is carried out by a person or firm specially authorized by Gebrüder Martin, the
operator of the product is required to obtain from the repairer a certificate with details about
the nature and scope of the repair work done. This certificate must show the date of the repair
and the details of the person or firm carrying out the work and must be signed.
In all cases where a party other than the product manufacturer performed the work, repaired
products must be additionally marked with the repairer’s ID label.

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 17
Improper interventions or alterations performed by third parties during the period of limitation
shall void any and all warranty claims. Performing unauthorized actions on the product is
strictly prohibited at any time. Non-compliance will void any liability claim against
Gebrüder Martin.
Gebrüder Martin guarantees the safety and functional capacity of the system only if an initial
commissioning is carried out and the device is approved for operation with a declaration of
handover.
1.5 User’s Inspection
•Immediately upon receipt, the goods must be checked for completeness and potential
damage in transit.
•Notice of any such damage must be given immediately.
1.6 Hotline
•Should you have any questions on how to handle the product or use it for clinical
applications, please do not hesitate to contact the Product Management:
Tel: [phone]
Fax: [phone]
•Should you have any technical questions or questions concerning maintenance contracts or
training courses, please contact our Martin Service Center:
Tel: [phone]
Fax: [phone]
E-Mail: [e-mail]
NOTICE
To answer your technical questions as efficiently as possib
le, our service technicians require
the serial number of the product. Therefore, please have this number at hand when
contacting our hotline. It is part of the information provided on the rating plate; see
section 4.1 “Information on the Rating Plate”, page 25.

Mounting Instructions
0BCEMOR Monitor Suspension System
18 Revision 1
2Notices Concerning this Document
Failure to observe thi
s document can lead to serious or even lethal injury to the
patient or the user!
Improper handling and care as well as non
-intended use can lead to premature wear and/or
pose a risk to patients and users!
It is the operator
’s responsibility to ensure that all personnel handling the product have
understood and do observe the notes and instructions in this document.
•Every user is required to read this document completely and follow it carefully.
•In particular, be sure to heed all cautions, warnings and danger notices.
•Keep this document accessible to users at all times.
2.1 Validity of this Document
This document applies to CEMOR.
This document is valid only in conjunction with:
•Instructions for use of the suspension arm system
•Instructions for use of the approved accessories for CEMOR

Mounting Instructions
0BCEMOR Monitor Suspension System
Revision 1 19
2.2 Applicable Mounting Instructions
The Mounting Instructions of CEMOR comprise three separate parts and are only valid if all
parts are available and complete at the site of assembly.
The three separate parts are as follows:
Fig. 2-1: Ceiling mount
•Part 01:
Ceiling mount
Interface plate on the raw ceiling
Intermediate ceiling set and interface plate
Fig. 2-2: Suspension arm system
•Part 02:
Suspension arm system
Fig. 2-3: CEMOR
•Part 03:
CEMOR

Mounting Instructions
0BCEMOR Monitor Suspension System
20 Revision 1
2.3 Symbols Used in this Document
Words marked with ®are trademarks owned by the respective proprietors.
Throughout this document, important information (such as general or safety-related notices) is
marked with the following symbols and signal words:
WARNING
Life hazard or serious injury!
Indicates a situation which, if not avoided,
could result in death or serious injury!
CAUTION
Risk of injury!
Indicates a situation which, if not avoided, could result in minor or moderate injury!
NOTICE
Risk of material damage!
Indi
cates a situation which, if not avoided, could lead to material damage (loss of time, data
loss, device/machine failure, etc.)!