Kohler 8787T-B01 User manual

8787T-B01
8787T-B03
8787T-B01
8787T-B03
0.05~0.86MPa
8787T-B01
8787T-B03
8787T-B01
8787T-B03
0.05~0.86MPa
2008
2008
冲洗方式 两段冲洗
巴尔顿 BARDON
小便感应器
URINAL SENSOR
安装说明书
INSTALLATION INSTRUCTIONS
K-8787T-B01(DC/直流型)
K-8787T-B03(AC/交流型)
平均冲水量不大于3.8L
average flushing is no more than 3.8L
1106445-T01-A
-1-

1045448
Center Unit Spring
顶针压簧
1045445
"O" Ring
"O"型圈
1045451
"O" Ring
"O"型圈
1045447
"O" Ring
"O"型圈
1045451
"O" Ring
"O"型圈
Filter Bolt
滤网固定栓
1045450
Gasket
密封垫片
1045449
Center Unit Assy
顶针组件
1045441
Fixed Cap
固定帽
1039038
Filter
滤网
Sponge Gasket
电控盒垫圈
1019266
Sensor Lens
装饰条
1060668
Control Box Assy.
电控盒组件
1056053
Battery Box Assy.
电池盒组件
8787T-B01 选用
8787T-B01 Use Only
Screw M4X50
螺钉M4X50
Screw M4X5
螺钉M4X5
Screw M2.5X6
螺钉 M2.5X6
1045462
Membrane Bracket Assy.
动膜支架组件
1056081
Solenoid Valve Assy.
电磁阀
Screw M3X8
螺钉 M3X8
1045459
"O" Ring
"O"型圈
Restrictor
节流器
Screw M3X8
螺钉M3X8
Pressing Board
压板
1045461
DiaphragmsAssy.
动膜组件
1045456
1045460
Spring
动模压簧
1108556
Bracket Assy.
固定板组件
1045458
Valve Cover
阀盖
Connection
出水接头
Lock Nut
六角吊紧螺母
Valve Body
阀体
Valve Box
暗盒
Connector
接插件
16306T-NA
8787T-B03 Use Only
8787T-B03 选用
AC
1019265-CP
1019265-SC
Cover
面板
"O" Ring
"O"型圈
"O"Ring
"O"型圈
交流电源
Connector
接插件
Bracket, Control Box
电控盒固定架
Screw M3X6
十字沉头螺钉M3X6
Hex Pan
2.5mm内六角扳手
"O" Ring
"O"型圈
1039036
Adjustment Bolt
调节栓
LockNut
六角吊紧螺母
-2-
1106445-T01-A

dd
e.
T
523
K-4978T-ET
K-4978T-ER
≈320±40
≈320±40
≈150
158
158
158
158
3/4” Spud
管接头
523 523
1/2”接头
1/2”接头
1/2”接头
1/2”接头
515±20 420±40
1/2”接头
395
1/2”接头
370
e.
K-19699 K-18645T
320
≈160
158
158
158
158
158
158
158
158
1/2”接头
1/2”接头
3/4” Spud
管接头 320±40 1/2”接头
1/2”接头
1/2”接头
1/2”接头
1/2”接头
1/2”接头
1106445-T01-A
-3-

8787T-B03
8787T-B03
8787T-B03
8787T-B01
8787T-B03
8787T-
B01
NOTE: It is recommended that a temporary rubber or plastic
hose is attached to the inlet pipe, and the water supply
line should be flushed clean of dirt and debris.
注意：建议在连接供水时,在供水管上连接一个临时橡皮或塑料软
管，冲洗供水管道，确保水干净，管道内无沙石、污垢等。
-4-
1106445-T01-A

B
3
B
3
警告：一个交流电源盒最多可连接两个感应器。
1106445-T01-A
-5-

a
8787T-B01
8787T-B03
anticlockwise to
8787T-B01
8787T-B03
逆时针 顺时针
-6-
1106445-T01-A

在电源接通前，务必清理感应窗口前的杂物，
Set Working Status
The product comes our factory with:
1. The working status is set as dual-flush. If you want to
cancel the first flushing function, place manual flush stick
adjacent to right side of sensing window for more than 1
second during the 10-minute standby period (Human
presence in sensing range would cause the indicator to
flash fast).The sensor would generate a flushing cycle to
indicate the setup of the sensor has been adjusted to after-
use flushing. If the action is not completed during this 10
minute, or you need to restore the working status to dual-
flush, plug off the power cord and reconnect the power
supply until the indicator stops flashing and repeat the
above procedures.
2. The diction time is set as 2s to avoid improper function in
narrow toilets, the detection time is automatically set from
2s to 5s.
,.1 10 (
)
110
2. 2 25
1106445-T01-A
-7-

Hex Pan
-8-
1106445-T01-A

1106445-T01-A
-9-

Keep flushing indicator not
flashing. 1. The small hole of diaphragms assembly
is blocked.
2. Foreign objects exist in valve chamber
1. Clean the small hole of diaphragms
assembly
2. Clean the valve chamber and diaphragms
with a brush
2. 阀腔内有杂物 2. 清洗阀腔与膜片
1. 膜片组件小孔堵塞 1. 清理膜片组件小孔
感应指示灯 1.电池耗尽（直流电）
2.刚刚停电 (交流电)1.更换新电池 2.检查总电源
1. Out of electricity (DC)
2. Just power cut (AC) 1. Replace batteries 2. Check the power supply
-10-
1106445-T01-A