Kolpin Outdoors 2772 Instruction sheet

1
© 2020 Kolpin Outdoors Inc. REV 00
Honda Pioneer 700 - Half Windshield
Product Instructions | Part No: 2772
Kolpin Outdoors, Inc. | 9955 59th Ave N | Plymouth, MN 55442
[phone] or [phone] | www.kolpin.com | [e-mail]
Application: Verify accessory fitment at Kolpin.com.
Before You Begin: Read these instructions and
check to be sure all parts are accounted for. If any items
are missing, do not return to the store. Call us at 1-877-
956-5746 for assistance. Please retain these instructions
for future reference and parts ordering information.
Dealers: Provide Instruction Manual to customer at time
of purchase.
Tools Required: 4mm Hex Wrench (or Socket), Wire
Cutter or Shears, and Torque Wrench
Product Contents:
Item Description Qty Part Number
1Windshield Panel 1
2Clamp - 1.75" Diameter 2K100137
(Qty 1)
3Button Head Screw - M6 x 18mm 6
4Lock Washer - M6 6
5Domed Shoulder Washer - M6 4
6Clamp Spacer - 1.6mm Thick *4K100138
(Qty 1)
7Bulb Seal - 48" 1PUR3355
1
7
3
4
345
2
*Extra Component Quantity Supplied
6

2
© 2020 Kolpin Outdoors Inc. REV 00
Installation Instructions:
1. Shift vehicle transmission into PARK. Turn key to OFF
position and remove from vehicle.
2. Carefully remove Windshield Panel from box and place on
a clean flat surface that won’t scratch the Windshield. We
recommend leaving the protective film on both sides of the
Windshield Panel during assembly and only partially peel-
ing it back in locations where mounting components are
attached.
3. Firmly press the Bulb Seal [Item 7] onto the bottom edge
of the Windshield Panel. Excess length of the Bulb Seal
can be trimmed. See Illustration 1-1.
4. Attach the two Clamps [Item 2] to the back side of the
Windshield Panel. Each Clamp uses two Button Head
Screws [Item 3], two Lock Washers [Item 4], and two
Domed Shoulder Washers [Item 5]. The Kolpin logo on the
Clamp should face the outside of the vehicle when closed.
Do not tighten hardware yet. Leave Clamps in open posi-
tion for assembly onto the vehicle. See Illustration 1-2.
5. Carefully position the Windshield assembly onto vehicle
Roll Cage. Insert one Clamp Spacer [Item 6] between
each Clamp [Item 2] and the Roll Cage. The two remaining
Clamp Spacers [Item 6] can be discarded. See Illustration
1-3.
6. Assure the Windshield is aligned evenly and the Bulb Seal
is compressed onto the vehicle bodywork.
7. Secure each Clamp to the Roll Cage using one Button
Head Screw [Item 3], and one Lock Washer [Item 4].
8. Tighten all Button Head Screws [Item 3] to torque specifi-
cation below.
9. Remove the protective film from BOTH sides of the Wind-
shield Panel. Protective film may be clear on one or both
sides which can be difficult to see.
10. Re-inspect hardware before and after riding or trailering.
Assembly Time: Approximately 15 minutes
Important: This product is exclusively designed for your vehicle. Please read the installation instructions thoroughly before begin-
ning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all
installation steps correctly in the sequence shown.
Ill. 1-1
Ill. 1-3
SPECIFIED FASTENER TORQUE:
7 ft. lbs. (84 in-lb) (9.5 Nm)
Ill. 1-2

3
© 2020 Kolpin Outdoors Inc. REV 00
Windshield Cleaning Information:
• Remove all dirt, mud, dust and debris from Windshield with water before cleaning.
• Use a mild soap or dishwashing detergent along with a soft sponge or soft cotton cloth to clean Windshield surface. Do not apply in direct sun-
light. Rinse with water immediately and dry with a soft cotton cloth or chamois.
• Always test cleaning agents in a small inconspicuous area prior to cleaning entire panel.
• Never use Windshield cleaning fluids (409, Windex, etc.), gasoline, high alkaline cleaners, or solvents.
• Never use abrasives, brushes, razor blades, scrapers, squeegees, gloves or dirty cloths.
For additional assistance, please contact Kolpin customer service department at
[phone] or [phone] or email [email protected].
One Year Limited Warranty
For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser, free of charge, any part or parts found upon ex-
amination by Kolpin to be defective in material, workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be borne by the purchaser. If Kolpin determines that the
product must be returned to the factory for credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and shipping
instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper maintenance, normal wear, or other causes
beyond the manufacturer’s control. In order to protect you and your ATV, certain parts of the accessory system and/or hardware are designed to fail
when the equipment is over-stressed. Parts that are lost due to loosening and improper maintenance are not covered under warranty. This warranty
does not cover removal or reinstallation labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original manufacturer’s warranty. Most hardware is general in na-
ture and is easily obtained locally. Be sure to replace with minimum metric class 8.8 specification.
TO AVOID SERIOUS INJURY OR DEATH:
1. DO NOT TRAILER VEHICLE FACING REARWARD WITH WINDSHIELD INSTALLED. AIRFLOW MAY CAUSE
WINDSHIELD TO SEPARATE FROM VEHICLE, RESULTING IN AN ACCIDENT AND SEVERE INJURY OR
DEATH. REMOVE WINDSHIELD OR TRANSPORT VEHICLE IN ENCLOSED TRAILER.
2. UTVs ARE TO ONLY BE DRIVEN WITH CLEAN WINDSHIELDS FOR DRIVING VISIBILITY. IF DIRT OR DEBRIS
ACCUMULATES ON THE WINDSHIELD WHEN RIDING, STOP THE UTV AT THE NEXT SAFE LOCATION ON
THE TRAIL TO CLEAR OFF THE WINDSHIELD BEFORE YOU RESUME RIDING.
3. ONLY INSTALL WINDSHIELDS THAT ARE DESIGNED FOR THE MAKE AND MODEL OF THE UTV. INSTALLA-
TION OF A WINDSHIELD THAT WAS NOT DESIGNED FOR THE UTV MAKE AND MODEL CAN IMPACT WIND-
SHIELD DURABILITY AND PERFORMANCE.
4. READ AND UNDERSTAND WINDSHIELD INSTRUCTION SHEETS AND UTV OWNER MANUAL BEFORE WIND-
SHIELD INSTALLATION OR OPERATING THE VEHICLE.
5. PERIODICALLY CHECK FOR WEAR AND TIGHTNESS OF ALL FASTENERS. ALWAYS INSPECT BEFORE AND
AFTER RIDING OR TRAILERING. REPLACE OR RE-TORQUE FASTENERS AS NECESSARY.
!!
DANGER