Kolpin Outdoors 34-9020 Installation and operating instructions

© 2019 Kolpin Outdoors Inc. REV 00
PLOW MOUNT KIT
FOR CF MOTO UFORCE 1000
P/N 34-9020
ASSEMBLY / OWNERS MANUAL
Application
PLOW PUS FRAME NO. 34-0000 or 34-0070
Before you begin, please read these instructions and check to be sure all parts and tools are ac-
counted for. The following instructions contain details required to install and service the contents of
this kit.

2
© 2019 Kolpin Outdoors Inc. REV 00
OPERATING INSTRUCTIONS
Congratulations! You’ve just purchased the most durable plow component in the industry. Kolpin plow components work great for
summer or winter plowing. With proper care and maintenance, your Kolpin plow system will last for years to come!
NOTICE
Plow op ration r quir s
additional compon nts for op ration: Kolpin Plow
Blade, Kolpin Plow Push Frame, High Rise Plow
Push Frame, Winch Kit *
*These components may be specific to your vehicle.
Please read and understand all assembly instructions, notices and warnings before assembling and operating your Kolpin plow
system.
Follow th s guid lin s to nsur satisfactory op ration:
• Read this manual and your ATV/ UTV operators manual before use.
• Periodically check for wear and tightness of all fasteners. Replace or re-torque fasteners as necessary.
• Before first use, set plow in the furthest right or left angled position to check for interference with the vehicle.
• Operate with extreme caution on slopes and rough terrain. Be familiar with the area before you plow.
• Be aware of immovable objects that could be hidden in the area you are plowing.
• To avoid damage when pushing snow into a pile, reverse direction before raising the plow blade.
• Do not ram the plow blade into piles of snow.
• For best results, set the suspension preload of your ATV/ UTV to the stiffest setting.
• To reduce steering effort and increase mobility, set the air pressure of your tires to the maximum pressure specification.
• The plow skids are adjustable. General skid setting is even with the plow wear bar bottom edge, higher settings reduce the
chance of rocks and gravel from being collected.
• To increase traction during plow operation, operators can try: Securing weight to the ATV/ UTV for additional tire downforce,
reducing tire air pressure, or installing tire chains.
SAFETY INFORMATION
Our plow systems were designed with your safety in mind. Please read and understand all Cautions, Notices and Warnings in this
manual before you begin. In order to protect you and your ATV/UTV, certain parts of the plow system and/or hardware are designed to
fail when the equipment is over-stressed.
WARNING
TO AVOID SERIOUS INJURY OR DEATH:
1. DO NOT EXCEED 5 MPH (8 KMH) WITH BLADE INSTALLED
2. OPERATE WITH EXTREME CAUTION ON SLOPES, STEEP GRADES, AND ROUGH TERRAIN
3. ALLOW NO RIDERS ON BLADE OR ATV WHILE MOVING OR STATIONARY
4. KEEP BYSTANDERS AWAY FROM THE BLADE OR ATV WHILE MOVING OR STATIONARY
5. WHEN PUSHING HEAVY MATERIAL, DIRECTION CONTROL MAY BECOME DIFFICULT
6. BEFORE ADJUSTING BLADE: STOP ATV ENGINE; SET AND LOCK BRAKES; RAISE AND LOCK BLADE
7. LOWER BLADE TO DOWN POSITION WHEN BLADE AND ATV ARE NOT IN USE
8. READ BLADE INSTRUCTION SHEETS AND ATV OWNER’S MANUAL
!!

3
© 2019 Kolpin Outdoors Inc. REV 00
Kit Cont nts:
It m Qty Part D scription Part Numb r
11UForce Mount Plate -
52Square U-Bolts, M8-1.25 x 105mm -
94Carriage Bolt, Zinc Plated, M8-1.25 x 25mm LG -
10 8Flange Locknut, Zinc Plated, M8-1.25 -
11 1Instruction Guide (not shown) -
32Front Spacer Bracket -
22Welded Nut Bracket -
42Rear Spacer Bracket -
64ex Bolt, Zinc Plated, M8-1.25 x 80mm LG -
84Lock Washer, Zinc Plated, M8 -
74Flat Washer, Zinc Plated, M8 -
2
3
1
4
5
6
8
7
10
9
10

4
© 2019 Kolpin Outdoors Inc. REV 00
BEFORE YOU BEGIN:
• Your Kolpin acc ssory is xclusiv ly d sign d for
your v hicl
• Pl as r ad and und rstand all instructions
• V rify all parts and tools ar account d for
• To nsur a satisfactory installation, follow all st ps
corr ctly and in th s qu nc d scrib d
• K p th s instructions for futur r f r nc or for
informational r qu sts
• To facilitat installation, mak sur that your v hicl
is cl an and fr of d bris
• All dir ctions r f rring to right and l ft ar wh n th
rid r is sitting on th machin
• Th plastic skid plat will n d to b modifi d to b
r install d on th v hicl .
TOOLS REQUIRED:
• Standard M tric Wr nch and Sock t S t
• Drill or cutting tools for plastic
APPROXIMATE ASSEMBLY TIME: 30 minut s
Not : R moval and modification of th plastic skid plat is r comm nd d.
Note: Additional time may be required to accommodate other installed
accessories.
Note: If any hardware is missing, do not return to the store. Call us to
help, Toll Free 1-877-956-5746.
Spar Kit Not s:
• Spar kits may contain xtra hardwar that is us d for oth r mount kits. Extra hardwar can b discard d.
• U-bolts suppli d in spar kits may b long r than original and may n d to b cut to siz .
SPARE KITS
Hardwar kit
P/N 34-0010
It m D scription
5Square U-Bolts, M8-1.25 x 105mm 4x
6ex Bolt, Zinc Plated, M8-1.25 90mm LG 2x
7Flat Washer, Zinc Plated, M8 2x
8Spring Lock Washer, Zinc Plated, M8 2x
9Carriage Bolt, Zinc Plated, M8-1.25 x 25mm LG 4x
10 Flange Locknut, Zinc Plated, M8-1.25 12x
- Flange Locknut, Zinc Plated, M10-1.5 2x
- ex Nut, Zinc Plated, M8-1.25 2x
- ex Bolt, Zinc Plated, M8-1.25 45mm LG 2x
- Carriage Bolt, Zinc Plated, M10-1.5 x 40mm LG 2x

5
© 2019 Kolpin Outdoors Inc. REV 00
Installation Pr p:
1. Detach the Front plastic
skid plate and two R /L
side plastic skid plates from
the vehicle by removing the
OEM fasteners as shown
and save for later. (See
illustration 1-1).
2. From under the vehicle,
align the mount plate (item
#1) with the frame. Center
the mount plate side to side
on the vehicle frame as
shown. (See illustrations
1-2 and 1-3).
3. Using the mount plate (item #1) as a pattern
template, scribe or mark the u-bolt / bolt hole
locations into the plastic skid plates.
4. Drill holes through the skid plate at locations
marked. Use a 3/8” to 1/2” bit to create an
oversized hole that will allow some relief when
installing hardware. (See illustration 1-2).
Note, a high speed cutting tool (like a
Dremel) with a cutting bit will also work.
Ill. 1-1
Ill. 1-2
Ill. 1-3
Front
R
L
FRONT
#1
Align sides with
angled frame tubes
Skid plate nut insert
will be near center
of square hole
FRONT
oles marked
for plastic
skid plate