Kontron SDML-WLU0 Series User manual

Kontron SDML-WLU0 Series - Quick Installation Guide - Version 1 - P/N: 0D2SDMLWLU010000 // 1

SDML
-WLU0 SERIES - QUICK INSTALLATION GUIDE
Thank you for purchasing the Kontron SDML-WLU0 Series embedded module. This document provides information to
allow you to quickly install this product.
Packing Checklist
1. Take the SDML-WLU0 Series out of the packing box and check if the unit is properly secure in the plastic bag.
2. Check the contents of the carton box: (*: optional)
SDML-WLU0 Series module
Quick Installation Guide
Driver CD
Top Side Jumper and Internal Connector Locations
1
2
3
12
4
5
6
8
9
10
11
13
14
15
16
17
18
7
19
20

Kontron SDML-WLU0 Series - Quick Installation Guide - Version 1 - P/N: 0D2SDMLWLU010000 // 2
Jumper List
Item Designation Description
1 JP1 MFG Mode Selection
2 JP3 USB Power Selection
3 JP4 M.2 Key B Lane 0 Selection
4 JP5 Flash Descriptor Security Override Selection
5 JP6 AT / ATX Power Mode Selection
6 JP7 Clear CMOS Selection
Internal Connector List
Item Designation Description
7 CN18 RTC Power Input Wafer
8 CN1 FAN Wafer
9 CN2 Micro SIM Card Holder for M2B1
10 CN3 P80 Header LPC
11 CN4 SPI 10-pin Header
12 CN5 Activity Indicator Header for M2E1
13 CN8 USB 2.0 Port 8 & 9
14 CN9 Activity Indicator Header for M2B1
15 DIMM1 DDR4 Channel 0 SO-DIMM Slot
16 DIMM2 DDR4 Channel 1 SO-DIMM Slot
17 M2B1 M.2 Key B 2242 / 3042 / 2280 Slot
18 M2E1 M.2 Key E 2230 / 3030 Slot
19 M2M1 M.2 Key M 2242 / 2280 Slot
20 GF1 SDM Goldfinger

Kontron SDML-WLU0 Series - Quick Installation Guide - Version 1 - P/N: 0D2SDMLWLU010000 // 3
Jumper Setting
MFG Mode Selection (JP1)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation
- X Enable MFG Mode
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
USB Power Selection (JP3)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - +5 V
- X +5 VSB
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
M.2 Key B Lane 0 Selection (JP4)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - PCIe x1
- X SATA
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
2
3
1
2
3
1
2
3
1

Kontron SDML-WLU0 Series - Quick Installation Guide - Version 1 - P/N: 0D2SDMLWLU010000 // 4
Flash Descriptor Security Override Selection (JP5)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation
- X Flash Security Override
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
AT / ATX Power Mode Selection (JP6)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - ATX Power Mode
- X AT Power Mode
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
Clear CMOS Selection (JP7)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation (default position)
- X Clear CMOS (board does not boot with the jumper in this position)
“X’’ = Jumper set (short) and ‘‘-’’ = jumper not set (open)
2
3
1
2
3
1
2
3
1

Kontron SDML-WLU0 Series - Quick Installation Guide - Version 1 - P/N: 0D2SDMLWLU010000 // 5
Rear I/O Panel Connector Locations
Connector List
Item Designation Description
1 CN10 GbE LAN1 RJ45 Connector
2 CN11 GbE LAN2 RJ45 Connector
3 CN12 USB 3.1 Port 1, 2 Type A Connector
4 CN13 USB 3.1 Port 3, 4 Type A Connector
5 CN14 Micro SD Card Holder
6 CN15 Optical S/PDIF Audio Port
7 CN16 Audio Jack Line-out Connector (Green)
8 CN17 Audio Jack Mic-in Connector (Pink)
Indicator List
Item Designation Description
a LED1 Green Power LED
b LED1 Red Storage LED
1
2
5
3
3
4
4
6
7
8
a
b