Krick 20300 Instruction Manual

Seite 1 © Krick Modelltechnik, Germany, June 2015
Felix Building Instructions
Art. No. 20300
1. Assemble the boat stand from parts
1-2-3 as shown on the small plan.
2. Prepare the hull by trimming as shown
on the small plan Drawing 1. Carefully
remove the excess material sand
carefully down to the final height of 5mm
and shape the bow as
shown.
3. Lightly sand the inside
of the hull to provide a key
for the deck 5. Fit the deck
and sand if required to
ensure a snug fit. When
this is achieved Epoxy glue
the deck in position. (See hull sections
BB & CC for position.)
For the following sequence refer to the
main drawing
4. Parts 6-7. Fit the engine cover,
coamings and rear access hatch
coamings under the lower deck.
5. Part 9. Fit the rear upper deck support
and glue.
6. Part 10. Fit the seat supports and
glue.
7. Part 11. Check and fit the rear deck
hatch.

Seite 2 © Krick Modelltechnik, Germany, June 2015
8. Parts 12 to 16. Assemble the motor
mount as shown on drawing 2.
Then refer to drawing 3. Solder on the
motor wires and suppression capacitors.
Screw the motor to the mount with the
screws provided.
9. Parts 21 to 28. Carefully drill the hull to
accept the prop shaft, use an undersize
drill and file to fit. Insert the shaft and tube
and with the motor in position coupling 26
as an aligning jig to ensure complete
accuracy.
Carefully drill pilot holes for the motor
mount screws and screw the mount in
position. When fixed Epoxy glue the shaft
and support 28 in position.
10. Parts 29 to 33. Place the forward
locker cover 29 in the lower deck to the
rear of the removable engine cover. Glue
the main engine room coaming 30 in
place.
Assemble the engine room cover as
shown in drawing 5. Part 75 door step
panel can be fitted later after painting.
11. Parts 34 to 38. Mark and drill a hole
for the rudder shaft 35. The rudder tube
34 rests on the hull and should be
epoxied in place. Make up the rudder and
sand to the profile as shown on the plan.
Fit the rudder in place and fit the servo
control arm 104.

Seite 3 © Krick Modelltechnik, Germany, June 2015
12. Part 39. The main deck can now be
fitted and glued into place. When dry
sand the hull to until the edges are flush
with the deck.
13. Parts 40 to 43. Fit the rear deck
edge' 40 into position to support the rear
deck cover 41 Glue the forward hatch
cover 42 to the deck. Fit and glue in place
the deck bulkhead 43.
Before proceeding We recommend you
paint and detail the hull at this stage.
14. Parts 45 to 55. Assemble the cabin
frame as shown in drawing above.
Place in position on the main deck and
leave to dry.
When the glue has dried, fit and glue in
position the cabin sides 52. Carefully
mark out the roof panel as dimensioned
in drawing 8.

Seite 4 © Krick Modelltechnik, Germany, June 2015
Fix the roof to the cabin. When dry cut out
the roof as marked and also remove the
centre spar. Paint the cabin, inside and
out to your chosen colour scheme.
Drill the roof for the hand rail supports 54
fix these in position allowing a 2 mm gap
from the roof. Fit and glue the hand rail
55.
15. Parts 56 to 59. Fit, in position the
ships wheel and support screw the wheel
to the support with screw no 59
16. Parts 60 to 65. Construct the bridge
as shown on the main drawing and
drawing 10. Leave the bridge in a natural,
wood finish. Paint the roof to match the
Cabin roof.
17. Part 66. Glaze the main cabin and
the bridge using the supplied template.
(Glue with PVA wood glue).

Seite 5 © Krick Modelltechnik, Germany, June 2015
18. Parts 67 to 72. Fix in position the
seats and back supports as shown on
drawing section C-C. The seat and back
supports should be varnished.
19. Parts 73 to 74. Carefully assemble
and glue the two sets of steps. Satin
varnish when dry.
20. Parts 76 to 78. Fix the doors to the
removable cabin. Fix on the door
handles.
21. Parts 79 to 81. Assemble and fix in
place the battery holder as shown on the
main drawing.
22. Parts 82 to 84. Assemble the vent
pipe. Paint and fix in position.
23. Parts 85 to 95. Pre Paint andstain as
necesssary all the mast components.
Taper the mast as required until the lamp
fit in the position shown. Mount the mast
in the base support lock the mast in
position using two pins 92. See the main
drawing for the mast assembly. Drill
the mast for the boom. The boom end is
drilled and apiece of brass wire
inserted. The wire is the inserted into the
mast.
24. Parts 96 to 102. All the small fittings
can be painted and fixed in the positions
indicated on the main drawing. Drill a hole
in the deck for fixing the flag staff and
epoxy glue in position.
25. Parts 104 to 106. These components
should be fitted as shown on the
drawing to your radio control servo.
Stickers and letters
The letters are cut from weatherproof self
adhesive foil. Cut out the full word from
the foil and then tear off the rest material
around the letters. To leave the letters in
exactly the same distance to each other,
when removing the support material, glue
some tape over the letters, which you can
tear off later. The letters do not need to
be covered 100%. It is advisable to leave
the upper or lower edges of the letters
free for exact positioning of the letters.
Then carefully tear off the support
material and place the letters exactly into
place. Finally remove the tape carefully
from the letters.
Klaus Krick Modelltechnik
Industriestrasse 1
D-75438 Knittlingen
E-Mail: [email protected]

Seite 6 © Krick Modelltechnik, Germany, June 2015
Partslist
No. Description Qty. Material Location
1 Stand
(
bow
)
1 5 mm Pl
y
Sheet 5
2 Stand
(
stern
)
1 5 mm Pl
y
Sheet
,
5
3 Stand Sides 2 5 mm Pl
y
Sheet 5
4 Hull 1
A
BS
5 Deck
(
mid section
)
1 3 mm Pl
y
Sheet 2
6 En
g
ine cover coamin
g
s 2 1 mm Pl
y
Sheet 3
7 'Re a r Deck cOamin
g
2 1 mm Pl
y
Sheet 3
8 Rear Deck end coamin
g
2 1 mm Pl
y
Sheet 3
9 Rear U
pp
er Deck su
pp
ort 1 3 mm Pl
y
Sheet 2
10 Seat Su
pp
orts 9 3 mm Pl
y
Sheet 1
11 Rear Deck Hatch Cover 1 3 mm Pl
y
Sheet 2
12 385 Motor Holder 1 3 mm Pl
y
Sheet 1
13 540 Motor Holder 1 3 mm Pl
y
Sheet 1
14 Mctor Side Su
pp
orts 2 3 mm Pl
y
Sheet 1
15 Motor Base 1 3 mm Pl
y
Sheet 1
16 Side Fittin
g
s
(
Motor
)
2 3 mm Pl
y
Sheet 1
17 Motor 1 Ba
g
18 Electrics Pack 1 Various Ba
g
19 Wire 2 Ba
g
20 Motor Su
pp
ort Screws 3 Screws 2 mm x 6mm Ba
g
21 Pro
p
Tube + Shaft 1
22 Lockin
g
Collar 1 JT. Rin
g
Ba
g
23 Pro
p
40 mm
,
3 Blade 1 Plastic Ba
g
26 Cou
p
lin
g
1Ba
g
27 Motor Mount Screws 2 2
,
2 x 9
,
5 mm Ba
g
28 Pro
p
Shaft
,
Su
pp
ort 1 3 mm Pl
y
Sheet 1
29 Forward Locker Cover
(
Mid
)
1 3 mm Pl
y
Sheet 2.
30 En
g
ine Cover Coamin
g
(
Fwd
)
1 3 mm x 3 mm x 52 mm Loose
31 En
g
ine Cover Sides 2 3 mm Pl
y
Sheet 2
32 En
g
ine Cover Ends 2 3 mm Pl
y
Sheet 1
33 En
g
ineCover To
p
1 1 mm Pl
y
Sheet 3
34 Rudder Tube 1 Brass 4mm Ba
g
35 Rudder Shaft Brass Rod 1 3 mm x 85 mm Ba
g
36 Rudder Centre 1 3 mm Pl
y
Sheet 1
37 Rudder 2 1 mm Pl
y
Sheet 3
38 Rudder Su
pp
orit Lower Deck 1 1 mm Pl
y
Sheet 3
39 Main Deck 1 3 mm Pl
y
Sheet 1
40 Rear Deck Ed
g
e 1 1 mm Pl
y
Sheet 3
41 RearDeck Cover 1 3 mm Pl
y
Sheet 1
42 Forward Hatch 'Cover
(
Bow
)
1 3 mm Pl
y
Sheet 1
43 U
pp
er Deck.Bulkhead 1 3 mm Pl
y
Sheet 2
44 Steel Wire 1 0
,
8 x 330 mm Ba
g
45 Cabin Su
pp
ort 1 3 mm Pl
y
Sheet 1
46 Cabin Su
pp
ort 1 3 mm Pl
y
Sheet 1
47 Cabin Su
pp
ort 1 3 mm Pl
y
Sheet 1
48 Cabin Su
pp
ort 1 3 mm Pl
y
Sheet 1
49 Cabin Su
pp
ort 1 3 mm Pl
y
Sheet 1
50 Cabin Front 1 3 mm Pl
y
Sheet 1
51 Cabin Side Strin
g
ers 2 3 mm Pl
y
Sheet 1
52 Cabin Sides 2 1 mm Pl
y
Sheet 3
53 Cabin Roof 1 1 mm Pl
y
Sheet 3
54 Handrail Su
pp
orts 14 S
p
lit Pin Ba
g
55 Hand Rail 2 Steel 1 x 320mm Ba
g
56 Shi
p
s Wheel Su
pp
ort 1 Wood Sheet 4
57 Shi
p
s Wheel Su
pp
ort 1 Wood Sheet 4
58 Shi
p
s Wheel 1 Plastic Ba
g
59 Fixin
g
Screw 1 2
,
2 x 9
,
5mm Ba
g
60 Prid
g
e -
,
Sides 2 Wood Sheet 4
61 Window Ed
g
in
g
6Stri
p
wood 2 x 2 x 270 mm
62 Brid
g
e Front 1 Wood Sheet 4

Seite 7 © Krick Modelltechnik, Germany, June 2015
No. Description Qty. Material Location
63 Brid
g
e Rear 1 Wood Sheet 4
64 Window Ed
g
in
g
2Stri
p
Wood 2 x 2 x 140 mm
65 Cabin Roof 1 1 mm Pl
y
Sheet 3
66 Glazin
g
1 PVC Sheet Loose
67 Seat
(
Starboard
)
1 Wood Sheet 4
68 Seat
(
Port
)
1 Wood Sheet 4
69 Seat Back Su
pp
ort
(
Starboard
)
1 1 3 mm Pl
y
Sheet 1
70 Seat Back Su
pp
ort
(
Port
)
1 3 mm Pl
y
Sheet 1
71 Seat Back
(
Starboard
)
1 Wood Sheet 4
72 Seat Back
(
Port
)
1 Wood Sheet 4
73 Ste
p
Sides 4 Wood Sheet 4
74 Ste
p
Treads 6 Wood Sheet 4
75 Door Ste
p
Down Panel 1 Wood Sheet 4
76 Cabin Door
(
small
)
1 Wood Sheet 4
77 Cabin Door
(
lar
g
e
)
1 wood Sheet 4
78 Door Handles 2 Brass Pins
79 Batter
y
Holder Base 1 3mm Pl
y
Sheet 2
80 Batter
y
Holder Side 1 3 mm Pl
y
Sheet 1
81 Batter
y
Holder End 2 3 mm Pl
y
Sheet 1
82 Vent Stem 1 Dowel 8 x 32 mm Ba
g
83 Vent To
p
1 Dowel 12 x 8 mm Ba
g
84 Vent Fixin
g
Screw 1 2
,
2 x 9
,
5mm Ba
g
85 Mast Base Su
pp
ort 1 3 mm Pl
y
Sheet 1
86 Su
pp
ort Sides 2 3 mm Pl
y
Sheet 1
87 Mast 1 Dowel 5 mm x 140 mm Ba
g
88 Mast Boom 1 Dowel 2 mm x 40 mm Ba
g
89 Lam
p
Su
pp
ort 1 1 mm Pl
y
Sheet 3
90 Lam
p
Su
pp
ort 1 1 mm Pl
y
Sheet 3
91 Mast To
p
1 Wood Disc Ba
g
92 Brass Rod Fixin
g
Pins 3 1 mm x 60mm Ba
g
93 Fla
g
1Cloth Ba
g
94 Corda
g
e 1 1 mm x 200 mm Black Ba
g
95 Mast Lam
p
s 2 Plastic Ba
g
96 Stern Lam
p
1 Plastic Ba
g
97 Search Lam
p
& Base 2 Plastic Ba
g
98 Claxon 1 Plastic Ba
g
99 Navi
g
ation Li
g
ht Boxes 1
p
air Plastic Ba
g
100 Life Belts 3 Plastic Ba
g
101 Bollards 6 Plastic Ba
g
102 Fla
g
Pole 1 Plastic Ba
g
103 Name Plates
(
FELIX
)
2 Transfer Loose
104 Tiller Arm 1 Plastic Ba
g
103 Control Rod 2 Metal Ba
g
106 Collar 1 Metal Ba
g

Seite 8 © Krick Modelltechnik, Germany, June 2015
Pattern for cutting the windows from clear material

Seite 9 © Krick Modelltechnik, Germany, June 2015

Seite 10 © Krick Modelltechnik, Germany, June 2015