Krone EasyCut F 360 CV User manual

Original operating instructions
Disc Mower
EasyCut F 360 CV
EasyCut F 360 CR
EasyCut F 320 CV
(from serial no.: 915 529)
Order no.: 150 000 173 01 en
15.06.2015

Table of Contents
2
Pos: 1 /BA/Konfor mitätserklärungen/Easy Cut/Neu ab 2010/Easy CutF 320 C V/F 360 CV/F 360 CR @ 321\mod_142 4783049042_78.doc x @ 2479575 @ @ 1
EC Declaration of Conformity
We Maschinenfabrik Bernard Krone GmbH
Heinrich-Krone-Str. 10, D-48480 Spelle
hereby declare as manufacturer of the product named below, on our sole responsibility,
that the
Machine: KRONE front disc mower
Type / types: EasyCutF 320 CV, F 360 CV, EasyCut F 360 CR
to which this declaration refers is in compliance with the relevant provisions of
EC directive 2006/42/EC (machines)
.
The signing managing director is authorised to compile the technical documents.
Spelle, 24.02.2015
Dr.-Ing. Josef Horstmann
(Managing Director, Design and Development)
Year of manufacture: Machine No.:
Pos:2 /LayoutModule /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.doc x@ 4165 @ @ 1

Table of Contents
3
Pos: 3 /Überschrif ten/Überschrif ten1/ F-J/Inhaltsverzeic hnis @ 31\mod_12519699 52727_78.docx @ 302165 @ 1 @ 1
1 Table of Contents
Pos: 4 /BA/Inhaltsver zeichnis Sprachenne utral @ 10\mod_1221574899 104_0.docx @ 135495 @ @ 1
1Table of Contents...................................................................................................................................3
2Foreword.................................................................................................................................................6
3To this Document...................................................................................................................................7
3.1Validity................................................................................................................................................7
3.1.1Direction Information...................................................................................................................7
3.2Representation and Utilization of Warning Notes..............................................................................7
3.3Identification of the hazard warnings..................................................................................................7
3.4Purpose of Use...................................................................................................................................8
3.5Intended Use......................................................................................................................................8
3.6Service life of the machine.................................................................................................................8
3.7Safety Instructions and Accident Prevention Regulations .................................................................9
3.7.1Personnel Qualification and Training........................................................................................10
3.7.2Dangers in Case of Non-compliance with the Safety Instructions............................................10
3.7.3Safety-conscious work practices...............................................................................................10
3.8Attached devices..............................................................................................................................11
3.9PTO operation..................................................................................................................................11
3.10Hydraulic system..............................................................................................................................12
3.11Maintenance.....................................................................................................................................13
3.12Unauthorised Conversion/Modification and Spare Parts Production...............................................13
3.13Inadmissible Modes of Operation.....................................................................................................13
4Machine Description ............................................................................................................................14
4.1Machine overview.............................................................................................................................14
4.2Identification Plate............................................................................................................................22
4.3Information Required for Questions and Orders..............................................................................22
4.3.1Contact......................................................................................................................................22
4.4Introduction.......................................................................................................................................23
4.4.1Re-Ordering the Adhesive Safety and Information Labels .......................................................23
4.4.2Affixing the Adhesive Safety and Information Labels ...............................................................23
4.5Position of the Adhesive Safety Stickers on the Machine................................................................24
5Technical Data of the Machine............................................................................................................40
5.1Technical data..................................................................................................................................40
5.2Consumables ...................................................................................................................................46
5.2.1Filling Quantities and Lubrication Designations for Gearboxes................................................46
6Commissioning.....................................................................................................................................47
6.1Special Safety Instructions...............................................................................................................47
6.2First installation ................................................................................................................................47
6.3Adapting to the tractor......................................................................................................................47
6.4Mounting onto the Tractor................................................................................................................48
6.4.1Clutching points.........................................................................................................................48
6.4.2Lower suspension arm..............................................................................................................49
6.5PTO shaft.........................................................................................................................................50
6.5.1Length adjustment.....................................................................................................................50
6.6Preparation on the front-mounted disc mower.................................................................................51
6.6.1Install the PTO shaft..................................................................................................................51
7Start-up..................................................................................................................................................52

Table of Contents
4
7.1Preparations on tractor.....................................................................................................................52
7.2Install the PTO shaft.........................................................................................................................53
7.3Mounting and Adjusting the Relief Springs......................................................................................54
7.3.1Pushed Design..........................................................................................................................54
7.4Checking Spring Retaining Chain....................................................................................................56
7.4.1Trailed Design...........................................................................................................................57
7.5Tensioning Guard Cloth ...................................................................................................................57
7.6Lighting connection ..........................................................................................................................58
7.7Hydraulics.........................................................................................................................................59
7.7.1Special Safety Instructions........................................................................................................59
7.7.2Connecting the hydraulic lines..................................................................................................59
7.8Trial run after first installation...........................................................................................................60
7.9Checking Fitting................................................................................................................................61
8Driving and Transport..........................................................................................................................62
8.1Lighting.............................................................................................................................................62
8.2Clamp and Buffer .............................................................................................................................64
9Operation...............................................................................................................................................65
9.1Before mowing .................................................................................................................................65
9.2Tensioning Guard Cloth ...................................................................................................................66
9.3Moving the guards into the working position....................................................................................66
9.4Moving Guards into Transport Position............................................................................................67
9.5Parking support................................................................................................................................67
9.6Detaching the machine ....................................................................................................................68
9.7Dismounting Retaining Chains.........................................................................................................68
10Settings .................................................................................................................................................69
10.1Adjusting the Compensation Springs...............................................................................................69
10.1.1Pushed Design..........................................................................................................................70
10.1.2Trailed Design...........................................................................................................................71
10.2Adjusting the cutting height..............................................................................................................72
10.2.1Telescopic upper suspension arm............................................................................................72
10.3Setting Conditioner Speed...............................................................................................................73
10.3.1Changing Pulley........................................................................................................................74
10.3.2Replacing Pulley .......................................................................................................................75
10.3.3Tensioning Belt Drive................................................................................................................75
10.4Adjusting the conditioner plate.........................................................................................................76
10.4.1Adjustment for Swathing...........................................................................................................76
10.4.2Wide spreading.........................................................................................................................77
10.5Setting the Distance of the Rollers...................................................................................................78
11Maintenance..........................................................................................................................................79
11.1Special Safety Instructions...............................................................................................................79
11.1.1Test run.....................................................................................................................................79
11.2Spare Parts ......................................................................................................................................79
11.3Maintenance table............................................................................................................................80
11.4Tightening torques............................................................................................................................81
11.4.1Metric Thread Screws with Control Thread ..............................................................................81
11.4.2Metric Thread Screws with Fine Thread...................................................................................82
11.4.3Metric Thread Screws with Countersunk Head and Hexagonal Socket...................................82
11.4.4Deviating Torque.......................................................................................................................83

Table of Contents
5
11.5Intermediate PTO shaft....................................................................................................................83
11.6Rotary hub with shear fuse (optional) ..............................................................................................84
11.6.1After Shearing Off .....................................................................................................................88
12Maintenance - Gearbox........................................................................................................................90
12.1Input gearbox ...................................................................................................................................90
12.2Angular gearbox...............................................................................................................................91
12.3Angular gearbox...............................................................................................................................92
12.3.1Top part.....................................................................................................................................92
12.4Angular gearbox...............................................................................................................................93
12.4.1Bottom part................................................................................................................................93
12.5Gearbox for Top Roller Drive...........................................................................................................94
12.6Tensioning Belt Drive.......................................................................................................................95
12.7Oil level check and oil change on the cutter bar..............................................................................96
12.7.1Oil change.................................................................................................................................96
12.7.2Checking the oil level................................................................................................................96
12.7.3Aligning the Cutter Bar..............................................................................................................96
13Maintenance - Blade Changing...........................................................................................................98
13.1Checking the Cutter Blades and Blade Holder ................................................................................98
13.1.1Cutter Blades ............................................................................................................................99
13.1.2Blade screw connection..........................................................................................................100
13.1.3Blade Quick-Fit Device ...........................................................................................................101
13.1.4Periodical Inspection of the Leaf Springs ...............................................................................102
13.1.5Periodical Inspection of the Cutting Discs / Blade Drums.......................................................103
13.1.6Abrasion Limit .........................................................................................................................104
13.2Blade Changing on Cutting Discs ..................................................................................................105
13.2.1Blade Screw Connection.........................................................................................................106
13.2.2Blade Quick-Fit Device ...........................................................................................................107
13.3Replacing the linings......................................................................................................................108
14Maintenance – lubrication chart .......................................................................................................109
14.1Special Safety Instructions.............................................................................................................109
14.2Universally-Jointed Drive Shaft......................................................................................................109
14.3Intermediate PTO shaft..................................................................................................................110
14.4Lubrication Chart............................................................................................................................110
15Placing in Storage..............................................................................................................................111
16Before the Start of the New Season .................................................................................................112
16.1Special Safety Instructions.............................................................................................................112
16.2Test run..........................................................................................................................................112
16.3Friction Clutch ................................................................................................................................113
17Special equipment..............................................................................................................................114
17.1Special Safety Instructions.............................................................................................................114
17.2Adjusting Skids...............................................................................................................................114
18Disposal of the machine....................................................................................................................115
18.1Disposal of the machine.................................................................................................................115
19Index....................................................................................................................................................116
Pos:5 /LayoutModule /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.doc x@ 4165 @ @ 1

Foreword
6
Pos: 6.1 /Überschri ften/Überschri ften 1/U-Z/Vorwort @ 0\mod_ 1195627720123_78.doc x @ 982 @ 1 @ 1
2 Foreword
Pos: 6.2 /BA/Vor wort/EasyCut/Verehrter Kunde EasyCut @ 3\mod_1204546 394934_78.doc x@ 70529 @ @ 1
Dear Customer!
By purchasing the disc mower, you have acquired a quality product made by KRONE.
We are grateful for the confidence you have invested in us in buying this machine.
To be able to use the disc mower optimally, please read these operating instructions thoroughly
before you start using the machine.
The contents of this manual are laid out in such a way that you should be able to perform any
task by following the instructions step by step. It contains extensive notes and information about
maintenance, how to use the machine safely, secure working methods, special precautionary
measures and available accessories. This information and these instructions are essential,
important and useful for the operational safety, reliability and durability of the disc mower.
Pos: 6.3 /BA/Vor wort/EasyCut/Weiterer Verlauf EasyCut @ 3\mod_12 04546850246_78.doc x@ 70549 @ @ 1
Note
In the operating instructions which follow, the disc mower will also be referred to as the
"machine".
Pos: 6.4 /BA/Vor wort/Beachten Sie für Maschi ne @ 0\mod_1195626904076_7 8.docx @ 944 @ @ 1
Please note:
The operating instructions are part of your machine.
Only operate this machine after you have been trained to do so and according to these
instructions.
It is essential to observe the safety instructions!
It is also necessary to observe the relevant accident prevention regulations and other generally
recognised regulations concerning safety, occupational health and road traffic.
All information, illustrations and technical data in these operating instructions correspond to the
latest state at the time of publication.
We reserve the right to make design changes at any time and without notification of reasons.
Should you for any reason not be able to use these operating instructions either wholly or
partially, you can receive a replacement set of operating instructions for your machine by
quoting the number supplied overleaf.
We hope that you will be satisfied with your KRONE machine.
Maschinenfabrik Bernard Krone GmbH
Spelle
Pos:7 /LayoutModule /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.doc x@ 4165 @ @ 1

To this Document
7
Pos: 8 /Überschrif ten/Überschrif ten1/ U-Z/Zu diesem Dokument @ 107\ mod_1334231929021_78. docx @ 965257 @ 1 @ 1
3 To this Document
Pos: 9 /BA/Einleitun g/Gültigkeit/Easy Cut /Gültigkeit EasyC ut F 320 CV / EasyCut F 360 CV / EasyC utF 360 CR @ 321\ mod_1424786573834_7 8.docx @ 2479606 @ 2 @ 1
3.1 Validity
These operating instructions are valid for disc mowers of series:
EasyCut F 320 CV, EasyCut F 360 CV, EasyCut F 360 CR
Pos: 10 /BA/Zu diesem Doku mentRichtungsangab en_mit Überschri ft 3. Ebene @ 311\mod_14182092622 91_78.docx @ 2405467 @ 3 @ 1
3.1.1 Direction Information
Direction information in this document such as front, rear, right and left always applies in the
direction of travel.
Pos: 11 /BA/Sic herheit/6. Überarbeitete W arnhinweise/Ver wendung und Darstellung vonW arnhinweisen @ 121\mod_1 343375943997_78.do cx@ 1100795 @ 2 @ 1
3.2 Representation and Utilization of Warning Notes
Warning of dangers are highlighted in this document as warning notes and they are marked with
danger signs and signal words.
The warnings must be read completely and the measurements must be strictly adhered to in
order to avoid personal injury.
Pos: 12 /BA/Sic herheit/6. Überarbeitete W arnhinweise/Kennzei chnung der Gefahrenhi nweise (2012-07-26 15: 10:30) @ 28\mod_12502443 70070_78.docx @ 274714 @ 2 @ 1
3.3 Identification of the hazard warnings
Danger!
DANGER! - Type and source of the hazard!
Effect: Danger to life or serious injuries.
• Measures for hazard prevention
Warning !
WARNING! - Type and source of the hazard!
Effect: Injuries, serious material damage.
• Measures for hazard prevention
Caution!
CAUTION! - Type and source of the hazard!
Effect: Property damage
• Measures for risk prevention.
Pos: 13 /BA/Sic herheit/6. Überarbeitete W arnhinweise/Allge meine Funktionshinwei se (2012-07-26 15:24:3 9) @ 0\mod_1196869714452 _78.docx @ 15185 @ @ 1
General function instructions are indicated as follows:
Note!
Note - Type and source of the note
Effect: Economic advantage of the machine
• Actions to be taken
Instructions which are attached to the machine need to be followed and kept fully legible.
Pos:14 /LayoutModule /---------------Seitenumbruch----------------@ 0\mod_1196175311226_0. docx @ 4165 @ @ 1

To this Document
8
Pos: 15 /Überschrif ten/Überschrif ten2/ U-Z/Verwendungsz weck @ 1\mod_1201707246738_ 78.docx @ 54055 @ 2 @ 1
3.4 Purpose of Use
Pos: 16 /BA/Einleitu ng/EasyCut/Verwendun gszweck Mäher @ 3\mod_12 04547495418_78.doc x@ 70590 @ @ 1
The EasyCut disc mower is used for cutting crops growing on the ground (except maize).
Pos: 17.1 /Überschri ften/Überschri ften 2/A-E/Bestimmungs gemäßer Gebrauch (alt) @ 0\mod_1196401545090_78. docx @ 7728 @ 2 @ 1
3.5 Intended Use
Pos: 17.2 /BA/Einlei tung/Bestimmungsge mäßer Gebrauch/EasyCut/ Bestimmungsgemäßer Gebrauch (Einzahl) @ 3\ mod_1204548357809_78. docx @ 70671 @ @ 1
The disc mower is built exclusively for customary use in agricultural work (intended use).
Pos: 17.3 /BA/Einlei tung/Bestimmungsge mäßer Gebrauch/Nicht b estimmungs gemäss (2012-0 3-19 16:41:15) @ 0\mod_ 1196401324340_78. docx @ 7690 @ @ 1
Any use of the machine for other purposes is deemed not to be in accordance with intended
use. The manufacturer shall not be liable for any resulting damage; the user alone shall bear
the risk.
Operation in accordance with intended use also includes observing the operating, maintenance
and service instructions specified by the manufacturer.
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
proper operation. For this reason, unauthorised modifications shall exclude any liability of the
manufacturer for consequential damage.
Pos: 18 /Überschrif ten/Überschrif ten2/ K-O/Nutzungsdauer der Maschine @ 318\mod_142 3658430909_78.doc x@ 2465744 @ 2 @ 1
3.6 Service life of the machine
Pos: 19 /BA/Einleitu ng/Nutzungsdauer der Maschine_Text @ 318\mod_1 423556613022_78.d ocx @ 2463145 @ @ 1
– The service life of this machine strongly depends on proper use and maintenance as well as
the operating conditions.
– Permanent operational readiness as well as long service life of the machine can be
achieved by observing the instructions and notes of these operating instructions.
– After each season of use, the machine must be checked thoroughly for wear and other
damage.
– Damaged and worn parts must be replaced before placing the machine into service again.
– After the machine has been used for five years, carry out full technical inspection of the
machine. According to the results of this inspection, a decision concerning the possibility of
reuse of the machine should be taken.
– Theoretically, the service life of this machine is unlimited as all worn or damaged parts can
be replaced.
Pos:20 /LayoutModule /---------------Seitenumbruch----------------@ 0\mod_1196175311226_0. docx @ 4165 @ @ 1

To this Document
9
Pos: 21.1 /BA/Sic herheit/Sicherhei ts- und Unfallverhütungs- Vorschriften Swadro_ Ladewagen_EasyCu t @ 73\mod_1308298589597 _78.docx @ 655493 @ 2 @ 1
3.7 Safety Instructions and Accident Prevention Regulations
1 Please follow all generally applicable safety and accident prevention regulations in addition
to the safety instructions contained in these operating instructions!
2 The attached warning and safety signs provide important information for safe operation. Pay
attention to these for your own safety!
3 When using public roads, make sure to observe the applicable traffic regulations!
4 Make sure that you are familiar with all equipment and controls as well as with their
functions before you begin working with the machine. It is too late to learn this when you are
using the machine for work!
5 The user should wear close fitting clothes. Avoid wearing loose or baggy clothing.
6 Keep the machine clean to prevent the danger of fire!
7 Before starting or moving the machine, make certain that nobody is in the vicinity of the
machine! (Watch for children!) Make sure that you have a clear view!
8 Carrying passengers during operation and transport on the working implement is not
permitted.
9 Couple implements correctly! Attach and secure implements to specified devices only!
10 When attaching or detaching implements, place the supporting devices in the correct
positions!
11 Use extreme caution when attaching or detaching implements onto or from the tractor!
12 Always attach ballast weights properly to the fixing points provided!
13 Observe permitted axle loads, gross weight and transport dimensions!
14 Check and attach transport equipment, such as lighting, warning devices and protective
equipment!
15 Actuating mechanisms (cables, chains, linkages etc.) for remote controlled devices must be
positioned in such a way that no movements are unintentionally triggered in any transport or
working positions.
16 Ensure that implements are in the prescribed condition for on-road travel and lock them in
place in accordance with the manufacturer's instructions!
17 Never leave the driver's seat when the vehicle is moving!
18 Always drive at the correct speed for the prevailing driving conditions! Avoid sudden
changes in direction when travelling uphill or downhill or across a gradient!
19 Hitched implements and ballast weights affect the driving, steering and braking response of
the machine. Make sure that you are able to brake and steer the machine as required!
20 Take into account the extension radius and/or inertia of an implement when turning corners!
21 Start up implements only when all safety devices have been attached and set in the
required position!
22 Keep safety equipment in good condition. Replace missing or damaged parts.
23 Keep clear of the working range of the machine at all times!
24 Do not stand within the turning and swivel range of the implement!
25 Never operate the hydraulic folding frames if anyone is inside the swivel range!
26 Parts operated by external power (e.g. hydraulically) can cause crushing and shearing
injuries!
27 Before leaving the tractor, lower the implement onto the ground, apply the parking brake,
switch off the engine and remove the ignition key!
Pos:21.2 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.doc x@ 4165 @ @ 1

To this Document
10
Pos: 21.3 /BA/Sic herheit/Personalqua lifikation und -sc hulung@ 0\mod_119563938318 5_78.docx @ 1136 @ 3 @ 1
3.7.1 Personnel Qualification and Training
The machine may be used, maintained and repaired only by persons who are familiar with it
and have been instructed about the dangers connected with it. The operator must define areas
of responsibility and monitoring of personnel. Should personnel lack the required knowledge,
they must receive the required training and instruction. The operator must ensure that the
contents of these operating instructions have been fully understood by personnel.
Repair work not described in these operating instructions should only be performed by
authorised service centres.
Pos: 21.4 /BA/Sic herheit/Gefahren bei Nic htbeachtung der Sic herheitshinweise @ 0\mod_119 5639434013_78.doc x @ 1155 @ 3 @ 1
3.7.2 Dangers in Case of Non-compliance with the Safety Instructions
Failure to follow the safety instructions could result in personal injury and environmental
hazards as well as damage to the machine. If the safety instructions are not respected, this
could result in the forfeiture of any claims for damages.
Failure to follow the safety instructions could result, for example, in the following hazards:
• Endangering of persons due to not protected working areas.
• Breakdown of important machine functions
• Failure of prescribed methods for repair and maintenance
• Endangering of persons due to mechanical and chemical effects
• Damage to the environment due to leaking hydraulic oil
Pos: 21.5 /BA/Sic herheit/Sicherhei tsbewusstes Arbeiten_Tei l1 @ 0\mod_11956397925 76_78.docx @ 1174 @ 3 @ 1
3.7.3 Safety-conscious work practices
Always observe the safety instructions set out in these operating instructions, all existing
accident prevention rules and any internal work, operating and safety rules issued by the
operator.
The safety and accident prevention regulations of the responsible professional associations are
binding.
The safety instructions provided by the vehicle manufacturer should also be observed.
Observe the applicable traffic laws when using public roads.
Be prepared for emergencies. Keep the fire extinguisher and first aid box within reach. Keep
emergency numbers for doctors and fire brigade close to the telephone.
Pos:21.6 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.doc x@ 4165 @ @ 1

To this Document
11
Pos: 21.7 /BA/Sic herheit/Angebaute Geräte/ Geräte angebaut Easy Cut @ 3\mod_1204552588996_ 78.docx @ 70752 @ 2 @ 1
3.8 Attached devices
1 Use extreme caution when attaching or detaching implements onto or from the tractor!
2 Couple the respective application devices to the appropriate couplings (e.g. three-point
suspension) only and secure them in a way (transport, use) that excludes inadvertent lifting
or lowering of the device.
3 When using three-point linkage, the attachment categories of the tractor and the device
(e.g. PTO speed, hydraulic system) must be coordinated!
4 When using the outside controls for the three-point linkage, do not step between the tractor
and the device (risk of injury)!
Pos: 21.8 /BA/Sic herheit/Zapfwellenbe trieb Traktor @ 0\mod_11996 99899350_78.doc x@ 3326 4 @ 2 @ 1
3.9 PTO operation
1Use only PTO shafts specified by the manufacturer!
2The guard tube and guard cone of the PTO shaft and the PTO guard must be attached and
in good working condition (on the implement side, too)!
3Make sure that the required tube covers are in place for PTO shafts in transport and
working position!
4Before installing or detaching PTO shafts, disengage the PTO, switch off the engine and
remove the ignition key!
5When using PTO shafts with an overload safety or free-running coupling which are not
shielded by the guard on the tractor, mount the overload safety or free-running coupling on
the implement side!
6Always make sure that the PTO shaft is properly installed and secured!
7Attach chains to prevent the PTO shaft guard from rotating with the shaft!
8Before switching on the PTO, make sure that the selected PTO speed of the tractor
matches the permissible implement speed!
9Before switching on the PTO shaft make sure that no person is in the danger zone of the
device!
10Never switch on the PTO if the engine is switched off!
11No one should be in the vicinity of the rotating PTO or PTO shaft when the PTO is in use.
12Always switch off the PTO shaft when the angle is too large or the PTO shaft is not
required!
13 Caution! After disengaging the PTO danger due to the flywheel running on! Keep away from
the implement during this time. The machine may be worked on only if it is completely at
standstill and if the flywheel is secured by the parking brake.
14Cleaning, lubricating or adjusting PTO driven implements or the PTO shaft only with PTO
disengaged, engine switched off and ignition key withdrawn! Secure the fly-wheel with the
parking brake.
15Place the disconnected PTO shaft onto the support provided!
16After detaching the PTO shaft, attach the protective cover to the PTO end!
17If damage occurs, correct this immediately before using the implement!
Pos: 21.9 /BA/Sic herheit/Zapfwellenbe trieb Zusatz @ 2\mod_1203 524761314_78.docx @ 665 13 @ @ 1
Note
The instructions of the manufacturer must be observed with regard to the PTO shaft. (separate
operating instructions)
Pos:21.10 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

To this Document
12
Pos: 21.11 /BA/Sic herheit/Hydraulika nlage @ 2\mod_1203503691986 _78.docx @ 66225 @ 2 @ 1
3.10 Hydraulic system
1The hydraulic system is pressurised!
2When connecting hydraulic cylinders and motors, make sure the hydraulic hoses are
connected as specified!
3When connecting the hydraulic hoses to the tractor hydraulics, make sure that the
hydraulics of both the tractor and the implement have been depressurized!
4In the case of hydraulic connections between tractor and machine, the coupling sleeves and
plugs should be marked to ensure a proper connection! If the connectors are interchanged,
the function will be reversed (e. g. raising/lowering) - Risk of accident!
5When searching for leaks, use suitable aids to avoid the risk of injury!
6Liquids escaping under high pressure (hydraulic oil) can penetrate the skin and cause
serious injury! Seek medical help immediately should injuries occur! Danger of infection!
7Before working on the hydraulic system, depressurise the system and switch off the engine!
Pos: 21.12 /BA/Sic herheit/Hydraulika nlage Zusatz Alterung der Hydraulikschlauch leitungen @ 3\mod_1204552 944856_78.doc x@ 70772 @ @ 1
8 Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!
The new hoses must fulfill the technical requirements set by the manufacturer of the
implement!
Pos:21.13 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

To this Document
13
Pos: 21.14 /BA/Sic herheit/Wartung/W artung Mäher mit Gasspeic her+ Auswechseln von Arbeit swerkzeugen @ 0\mod_1195 647075607_78. docx @ 1442 @ 2 @ 1
3.11 Maintenance
1 Always make certain that the drive and the engine are switched off before doing any
repairs, maintenance or cleaning! - Remove the ignition key!
2 Regularly check that nuts and bolts are properly seated and tighten if necessary!
3 When carrying out maintenance work on a raised mowing unit, always use suitable means
to secure it against falling.
4 When replacing working tools with cutting edges, use suitable tools and gloves!
5 Oils, greases and filters must be disposed of correctly!
6 Always disconnect the power supply before working on the electrical system!
7 If protective devices and guards are subject to wear, check them regularly and replace them
in good time!
8 When performing electrical welding work on the vehicle and mounted devices, turn the
power supply off at main battery switch or disconnect generator cable and battery!
9 Replacement parts must at least comply with the technical requirements set by the
manufacturer of the implements! This is guaranteed by original KRONE spare parts!
10 Only use nitrogen for filling pneumatic accumulators - risk of explosion!
Pos: 21.15 /BA/Sic herheit/Eigenmächti ger Umbau und Ersatzteil herstellung @ 1\mod_120 1937705539_78.doc x @ 55745 @ 2 @ 1
3.12 Unauthorised Conversion/Modification and Spare Parts Production
Conversions or modifications of the machine are permitted only with prior consultation with the
manufacturer. Original spare parts and accessories authorised by the manufacturer help to
ensure safety. Use of other parts may void liability for resulting damage.
Pos: 21.16 /BA/Sic herheit/Unzulässige Be triebsweisen @ 11\mod_1 223357699923_78.doc x @ 145527 @ 2 @ 1
3.13 Inadmissible Modes of Operation
The operating safety of the delivered machine is guaranteed only when it is used as intended in
compliance with the introductory section "Intended use" of the operating instructions. The limit
values listed in the data charts should not be exceeded under any circumstances.
Pos:22 /LayoutModule /---------------Seitenumbruch----------------@ 0\mod_1196175311226_0. docx @ 4165 @ @ 1

Machine Description
14
Pos: 23.1 /Überschri ften/Überschri ften 1/K-O/Maschinenbe schreibung @ 107\mod_1334 231806004_78.doc x@ 965 201 @ 1 @ 1
4 Machine Description
Pos: 23.2 /Überschri ften/Überschri ften 2/K-O/Maschinenüb ersicht @ 0\mod_11955657 31130_78.docx @ 555 @ 2 @ 1
4.1 Machine overview
Pos: 23.3 /Abkürzung en /Abkürzungen Beschr eibung/EasyCut F 320 CV gesc hoben/EasyCut F 360 CV gesc hoben @ 321\mod_1424788 432426_78.docx @ 2479787 @ @ 1
EasyCut F 320 CV pushed / EasyCut F 360 CV pushed
Pos: 23.4 /BA/Maschi nenbeschreibung/ Maschinenübersicht/ Mähwerke/Maschinenüb ersicht EasyCut F 360 CV ge schoben Bild @ 241\mod_139 5241558809_78.doc x@ 189663 5 @ @ 1
EC-525-0
14
10
23
5
4
8
912
14
5
16
17
19
20
11
15
15
13
7
1
6
11 10
18
Fig. 1
Pos:23.5 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.doc x@ 4165 @ @ 1

Machine Description
15
Pos: 23.6 /BA/Maschi nenbeschreibung/ Maschinenübersicht/ Mähwerke/Maschinenüb ersicht EasyCut F 360 CV ge schoben Tabelle @ 242\mod _1395308523079_78. docx @ 1898512 @ @ 1
Pos. Description Pos. Description
1) Blade drawer 2) Drive universal shaft
3) Universal shaft support 4) Relief springs
5) Swath flaps 6) Tine conditioner / roller conditioner
7) Parking support*) 8) Guard cloth
9) Input gearbox 10) Friction clutch
11) Intermediate universal shaft 12) Angular gearbox
13) Lever to adjust the conditioner plate 14) Side guards
15) Guard cloth 16) Cutter bar
17) Safety device front 18) Belt drive
19) Blade key*) 20) Retaining chains
*) optional
Pos:23.7 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.doc x@ 4165 @ @ 1

Machine Description
16
Pos: 23.8 /Abkürzung en /Abkürzungen Beschr eibung/EasyCut F 320 CVgez ogen/EasyCut F 360 CV gezoge n @ 321\mod_142479064173 5_78.docx @ 2479988 @ @ 1
EasyCut F 320 CV trailed / EasyCut F 360 CV trailed
Pos: 23.9 /BA/Maschi nenbeschreibung/ Maschinenübersicht/ Mähwerke/Maschinenüb ersicht EasyCut F 360 CV ge zogen Bild @ 242\mod_13953 09564639_78.doc x@ 1898 648 @ @ 1
EC-524-0
14
10
23
5
4
8
9
12
14
5
16
17
19 11
1515
13
7
1
6
10
11
18
Fig. 2
Pos:23.10 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine Description
17
Pos: 23.11 /BA/Maschi nenbeschreibung/ Maschinenübersic ht/Mähwerke/Maschi nenübersicht EasyCut F 36 0 CV gezogen Tabelle @ 241\ mod_1395304263736_78. docx @ 1897864 @ @ 1
Pos. Description Pos. Description
1) Blade drawer 2) Drive universal shaft
3) Universal shaft support 4) Relief springs
5) Swath flap 6) Tine conditioner / roller conditioner
7) Parking support*) 8) Guard cloth
9) Input gearbox 10) Friction clutch
11) Intermediate universal shaft 12) Angular gearbox
13) Lever to adjust the conditioner plate 14) Side guards
15) Guard cloth 16) Cutter bar
17) Safety device front 18) Belt drive
19) Blade key*)
*) optional
Pos:23.12 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine Description
18
Pos: 23.13 /Abkürzun gen /Abkürzungen Beschr eibung/EasyCut F 360 C Rgesc hoben @ 242\mod_13953950 62772_78.docx @ 1900444 @ @ 1
EasyCut F 360 CR pushed
Pos: 23.14 /BA/Maschi nenbeschreibung/ Maschinenübersic ht/Mähwerke/Maschi nenübersicht EasyCut F 36 0 CR gesc hoben Bild _1 @ 261\mod_139 9444843585_78.doc x@ 19916 86 @ @ 1
EC-478-0
14
10
23
5
4
8
912
14
5
16
17
18
19
11
15
15
13
7
1
6
Fig. 3
Pos:23.15 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine Description
19
Pos: 23.16 /BA/Maschi nenbeschreibung/ Maschinenübersic ht/Mähwerke/Maschi nenübersicht EasyCut F 36 0 CRge schoben Tabelle @ 241\mod _1395242894024_ 78.docx @ 18969 29 @ @ 1
Pos. Description Pos. Description
1) Blade drawer 2) Drive universal shaft
3) Universal shaft support 4) Relief springs
5) Swath flaps 6) Tine conditioner / roller conditioner
7) Parking support*) 8) Guard cloth
9) Input gearbox 10) Friction clutch
11) Intermediate universal shaft 12) Angular gearbox
13) Lever to adjust the conditioner plate 14) Side guards
15) Guard cloth 16) Cutter bar
17) Safety device front 18) Blade key*)
19) Retaining chains
*) optional
Pos:23.17 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine Description
20
Pos: 23.18 /Abkürzun gen /Abkürzungen Beschr eibung/EasyCut F 360 C Rgez ogen @ 242\mod_1395394970 276_78.docx @ 1900335 @ @ 1
EasyCut F 360 CR trailed
Pos: 23.19 /BA/Maschi nenbeschreibung/ Maschinenübersic ht/Mähwerke/Maschi nenübersicht EasyCut F 36 0 CR gez ogen Bild @ 242\mod_1395309 680566_78.doc x@ 1898677 @ @ 1
EC-479-0
14
10
23
5
4
8
9
12
14
5
16
17
18 11
1515
13
7
1
6
Fig. 4
Pos:23.20 /LayoutModule/---------------Seitenumbruch----------------@ 0\mod_1196175311226_0.docx @ 4165 @ @ 1