L.L.Bean ADIRONDACK User manual

UPRIGHT ADIRONDACK CHAIR
Thank you for purchasing this Upright Adirondack Chair.
Assembly of this product requires a 7/16" wrench or adjustable
wrench. Having someone assist you by holding parts in place
during installation will make the process easier.
4522 0NPT7

STEP 1
Read through these instructions thoroughly.
We have found this to be of great value when
first assembling this product.
STEP 2
Remove all parts and hardware from packing
material. Wooden pieces should be placed
on a non-abrasive surface (like the carton or
carpet) to prevent damage to the finish.
STEP 3
Identify all parts using diagram at right
(A) Back Assembly
(B) Back Legs
(C) Right Arm
(D) Left Arm
(E) Seat Assembly
(F) Front Leg Assembly
STEP 4
Identify and count hardware using diagram at
right.
Assembly of this product requires a 7/16"
wrench (or adjustable wrench). Having
someone assist you by holding parts in place
during installation will make the process
easier.
NOTE: Make sure all parts are correctly
lined up before tightening.
STEP 5
Stand Seat Assembly (E) up on
edge as pictured on right. Insert
joint connector through bottom
predrilled hole of back leg (B) as
shown on right, then through the
bottom predrilled hole on the
back of the Seat Assembly. Do
not fully tighten. Repeat for the
other back leg (B).

STEP 6
After both back legs (B) are fastened, turn
Seat Assembly (E) up and place front of Seat
Assembly (E) into Front Leg Assembly (F).
Insert four joint connectors through the
predrilled holes of Front Leg Assembly (F).
The joint connector will go through the
predrilled holes in the front of the Seat
Assembly (E). Secure with a washer and lock
nut as shown on right.
STEP 7
To attach arms (C, D) insert two joint
connectors through the predrilled holes on
the inside of the Front and Back Legs (F, B),
then through the predrilled holes in the arm
cleats and secure with washers and lock nuts.
Do not fully tighten.
STEP 8
Attach Back Assembly (A) to Back
Legs (B) by inserting two 2-1/2” Lag
Bolts with washers through the top
holes in Back Legs (B), then tighten
into the Bottom Cleat of the Back
Assembly (A). Fully tighten.

STEP 9
Insert two 1-3/4” Lag Bolts with
washers through the predrilled holes
in the back arm cleats (C, D), then
into the predrilled holes of the
middle back cleat of Back
Assembly (A).
**Tighten all lock nuts and screws
securely on chair.
CARE
Thank you for choosing our classic L.L.Bean
Adirondack furniture. The natural finished
furniture is made of solid oak and finished
with a wood preservative. This oak
hardwood will gray slightly as it ages.
Painted furniture is made of maple hardwood
and finished with a rugged weather-resistant
acrylic paint. All of our Adirondack
Furniture is made in the United States.
Recommendations for extending the life of
your furniture:
•During inclement weather and
off-season, bring furniture indoors
or use a furniture cover.
•Over time, wood exposed to the
ground will absorb moisture,
which may cause rot. If you use
this chair on a lawn, occasionally
move it to a dry surface (patio or
deck) to allow the legs to dry out.
•A deck, porch, or patio is the best
location for your furniture.
•To clean, wipe accumulated dirt
with a solution of warn soapy
water and a soft cloth; rinse
thoroughly with clean water.
Over time your Adirondackfurniture will need
refinishing. We recommend the following:
•Lightly sand each piece with a fine grade of
sandpaper before applying paint or finish. You
do not have to sand down to bare wood.
•On painted furniture apply a primer first. Finish
with an outdoor weather resistant acrylic paint.
The original paint color can be matched at your
local hardware or paint store.
•If you have solid oak furniture, sand and finish
with any high-grade wood preservative.
www.llbean.com
Product Support 1 800 341 4341