Lee & Plumpton SmartTop Series User manual

No. 089 A/0951 Revision B 25/09/2019 1
www.leeandplumpton.co.uk
ASSEMBLY INSTRUCTIONS
RANGE SmartTop
REF: Double Desk
Read this leaet before
assembly
2 People
Required
COMPONENT PARTS
TOOLS REQUIRED BEFORE YOU BEGIN...
• Check you have all the tools and components required
• Keep children and animals away from small parts
• Ensure you have adequate space
• Assemble product on a at, clean surface
• Apply manual handling guidelines when building this item
• Pozi head screwdriver
Minimum 200mm long
• T30 Allen Key (Supplied)
• 5mm Allen Key
Important Information
Please check the below details before attaching computer hardware:
• Monitor maximum dimensions of 440mm width x 350mm height x 65mm depth.
• Keyboard maximum dimensions 475mm wide x 40mm depth
• The overall weight of the complete item is 50kgs, apply manual handling guidelines.
• Only use component xings supplied with this item.
• When closing monitor lid place hand in centre of the top to prevent trapping ngers or thumb and press down until
lid contacts latch.
Item A
60mm Chipfast Bolt NP
F/0486
Qty 6
Item B
Minix Bolt M6
F/0433
Qty 8
Item C
Wood Dowel
F/0431
Qty 4
Item D
Minix Alloy Cams 18mm
F/0434
Qty 8
Item E
Adjustable Foot Black
F/0606
Qty 6
Item F
Minix Cover Cap
F/0545
Qty 8
Item G
Hole Plugs Grey 5mm
A/0585
Qty 4

No. 089 A/0951 Revision B 25/09/2019 2
STEP 1
ASSEMBLY INSTRUCTIONS
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
STEP 9
STEP 10
CARE AND MAINTENANCE
STEP 8
STEP 11
J
J
J
J
J
L
L
L
L
I
I
I
I
K
K
K
G
G
G
G
F
F
F
F
F
F
G
G
G
G
K
E
E
E
E
E
E
A
A
A
A
A
A
G
G
G
G
B
B
B
B
B
B
FD
FD
FD
FD
C
C
C
B
B
Place top on a at even surface.
Place part (C) in appropriate holes
in modesty panel.
Push part (D) (with the arrows facing
out) into the holes of the modesty
panel. (Ensuring the holes are free
from debris).
Screw in 4 x Part (B), M6 minix
bolts, into the central cantilever leg.
Attach Modesty panel x 2 to the
central cantilever leg.
Take the modesty panels and lower
into the top. Ensuring the holes are
lined up.
Screw the remainder of part (B)
into the holes of the upright on the
cantilever legs to create a left and
right hand tting.
Attach part (E) to bottom of the
cantilevers.
Attach cantilever legs to modesty
locating parts (B) into the holes on
the modesty.
Clean using a damp cloth and mild detergent – do not use abrasive cleaners or bleach.
Remove the key from
the front of the units.
Use this key to unlock
the units and lift the lids.
Screw part (A) through cantilever top
rail into the holes in the top. Tighten
up the remainder of parts (D) in
modesty.
Attach monitor using screws provided
by monitor supplier. (Take time to
review which holes you need to use
which is dependent on monitor size.)
Apply part (G), hole plugs, to outside
of cantilever leg frame.