Lee & Plumpton Signature Storage Credenza User manual

A/1875 Revision A 08/01/2018
1
www.leeandplumpton.co.uk
ASSEMBLY INSTRUCTIONS
RANGE Signature Storage, Credenza Units.
REF: 740mm High, 1000mm High and 1200mm High
800mm and 1000mm Wide
Read this leaet before
assembly
2 People
Required
COMPONENT PARTS
Item 8
STO1_636
RH Sliding Door
Qty 1
Item 7
STO1_637
LH Sliding Door
Qty 1
Item 9
STO1_854
Shelf
Qty 1
Item 4
STO1_543
Lintel
Qty 1
Item 12
STO1_795
Double Track
Qty 1
Item 5
STO1_640
Top Panel Sliding Door
Qty 1
Item 2
STO1_881
LH Side Panel
Qty 1
Item 3
STO1_880
RH Side Panel
Qty 1
Item 1
STO1_568
Back Panel
Qty 1
Item 6
STO1_641
Bottom Panel
Qty 1
Item 11
A.0718
Bar Handle
Qty 2
Item 13
STO1_604
Wooden Adapter
Qty 4
Item 14
STO1_602
Running Part
Qty 4
Item 15
STO1_605
Bottom Guide
Qty 2
Item 16
STO1_597
Spacer
Qty 1
Item 17
STO1_603
End Stop
Qty 4
Item 18
A.0577
BCB Door Lock
Qty 1
Item 19
F.0629
Rapid Dowel (blue)
Qty, (See Table 1)
Item 20
F.0630
Rastex Cam
Qty, (See Table 1)
Item 21
F.0431
Wood Dowel
Qty 10
Item 22
F.0436, F.0446, F.0545
F.0575, F.0576, F.0577
Cam Cover
Qty, (See Table 1)
Item 23
F.0404A
Kd Block Female
(Brown)
Qty2
Item 24
F.0404B
Kd Block Male (Natural)
Qty 2
Item 25
F.0564
Shelf Support
Qty 4
Item 28
F.0469
M4x28 Handle Screw
Qty 4
Item 29
F.0492
16mm Euro Screw
Qty 4
Item 30
F.0475
3/4”x10g Pan Pozi
BZP
Qty 8
Item 31
F.0412
5/8”x6g CSK Pozi BZP
Qty 24

A/1875 Revision A 08/01/2018
2
TOOLS REQUIRED BEFORE YOU BEGIN...
• Check you have all the tools and components required
• Keep children and animals away from small parts
• Ensure you have adequate space
• Assemble product on a at, clean surface
• Apply manual handling guidelines when building this item
COMPONENT PART QUANTITIES FOR UNIT SIZE VARIATIONS (TABLE 1)
• Pozi head screwdriver
• Flat bladed screwdriver
• Hammer
• Ruler
• 2.5mm Allen key
STEP 1
ASSEMBLY INSTRUCTIONS
STEP 2
If the unit is 1000mm wide,
the 2 holes in the back panel
need to be at the bottom of the
bookcase.
If the unit is 740mm tall,
the 2 Cam holes at the top/
bottom centre of the back
panel are excluded.
ITEM W800 x H740 mm W1000 x H740 mm W800 x H1000mm W1000 x H1000 mm W 800 x H 1200 mm W 1000 x H 1200 mm
19 18 20 20 22 20 22
20 18 20 20 22 20 22
22 18 20 20 22 20 22
Lay the panels at on a soft
surface. Ensure all holes are free
of debris.
In the back panel (1) insert the
appropriate number of Cams (20)
and Wooden Dowels (21)
In both the sides (2) & (3), knock
in the White KDBlocks (24) and
push in the appropriate number of
Spreading Dowels (19).
In the Lintel (4) knock in the female
KDBlocks (21).
1
20
21
24
2
20
19
21
24
4
3
2
Assemble the two Sides to the
Back.
Before locking the Cams in the
Back, t the Lintel (4) between the
Sides.
Ensure that the Lintel is tted with
the holes in its long edge facing
out of the cabinet.
Tighten the Cams with a half turn
and tighten the screws in the KD
ttings behind the Lintel.
19
23

A/1875 Revision A 08/01/2018
3
STEP 3
ASSEMBLY INSTRUCTIONS
STEP 4
98.5
49
118
68.5
31
5
12
The Top (5) will have an aluminium
Track (12) screwed into it for safe
keeping, unscrew the Track and
retain the Screws (31).
Slide the four Running Parts (14)
in the Track, two in each groove.
All must face the same way.
Slide an End Stop (17) in to each
groove, one from each end (so
that the Running Parts cannot
come out of the grooves). Ensure
the open end of the End Stop
faces to the middle of the Track.
Ensure all the Runners move
smoothly and freely.
Looking closely at the Runners,
identify the side of the Runner that
has the two exible tabs. With
those tabs pointing to the rear
of the Top, screw the Track back
into the channel in the Top with
the screws you removed earlier.
Also note the height adjustment
thumbscrew.
The End Stops need to be set
accurately to ensure the Doors
close in the correct positions.
Looking down onto the Top
and with the Track away from
you, set the four End Stops to
the dimensions shown. The
dimension is to the back (un
open end) of the End Stop.
These dimensions set the stop
positions of the door in its open
& closed positions.
Push in Spreading Dowels (19)
into the Top and the Base (6).
12
14 Flexible Tabs – to be at
the rear when tted to Top
panel
17
19
Flexible Tabs x2
Height Adjustment
Thumbwheel
Open end
Dimensions to here from
edge of the Top panel

A/1875 Revision A 08/01/2018
4
STEP 5
STEP 6
STEP 7
ASSEMBLY INSTRUCTIONS
Attach the Top and the Base to
the Sides/Back/Lintel you built
earlier.
Stand the unit upright.
Screw the Bottom Guides (15) to
the Base, with the Screws (31) on
the inside.
If you are tting a Shelf, this is
the easiest point to do that.
Decide where you want the Shelf
to be and identify the holes in
the Sides (and Back if the unit is
1000mm wide).
Using Screw (29) t the Shelf
Support (25) to the Side (& Back).
Lay the Shelf (9) on the Supports.
Fit Cam Cover Caps (22) to the
Cams.
Prepare the two Doors (7) Left and
(8) Right by attaching the metal
Wooden Adapters (13) across the
circular cut out in the back of the
Doors with Screws (31).Attach
a Handle (11) to each door with
Screws (28).
On the back of the left hand Door
attach the “L” shaped Spacer (16)
with Screws (31) and push the
body of the Lock (18) through the
hole in the Door and attach with
Screws (31).
6
11
31
28
16
18
13
9
25
29
31 15

A/1875 Revision A 08/01/2018
5
ASSEMBLY INSTRUCTIONS
STEP 8
STEP 8
Each Door has a groove in the
bottom of it.
The left hand Door must be
tted rst.
Looking at the Track and Runners
beneath the Top, ensure that the
front groove has two runners in
the left hand half of the Track and
that they run easily.
Lean the Door back towards you
and place the groove in the Door
bottom over the left hand (front)
Bottom Guide on the Base.
Holding the top of the Door in
both hands push it towards the
Top panel and with your ngers
slide the Runners to align with the
cut-outs in the back of the Door.
The Door may need to be lifted
slightly to ease the alignment.
Grip the Door and the Runners
and squeeze the two until the
Runner clips into the door with a
distinct “Click”. It may be easier to
click one Runner to the Door rst,
then the other.
7
The right hand Door slides into
position behind the left hand
Door.
Slide the two Runners in the rear
groove of the Track over to the
right.
Twisting the right hand Door
slightly open on the right hand
side, engage the Door over the
Bottom Guide.
Slide the Door along the Bottom
Guide until the right hand edge of
the Door ts into the cabinet.
Keeping both Runners roughly
behind the Door Handle, slide the
Door to the left a little until you
can reach behind the door.
Push the left hand Runner towards
the middle of the door and engage
the right hand Runner in the right
hand cut-out on the back of the
Door. Push the left hand Runner
to the left until it engages with the
left hand Door cut-out.
Open the left hand (front) Door
and ensure that the two Runners
for the right hand Door are
positively engaged.
8

A/1875 Revision A 08/01/2018
6
STEP 9
ASSEMBLY INSTRUCTIONS
STEP 6
CARE AND MAINTENANCE
To adjust the Doors up or down,
nd the height adjustment
thumbscrew in the Runner that
you identied earlier and rotate it
with your nger.
To remove the Doors, feel the
Runner and nd the two exible
tabs you identied earlier. Pinch
these together between your rst
nger and thumb to disengage the
Runner from the Door. Take the
left hand Door off rst.
The cabinet can be adjusted for
levelling by turning the screw head
in the front corner of the Base
panel. There may be a Cover Cap
which will need to be removed to
access the screw head.
Clean using a damp cloth and mild detergent – do not use abrasive cleaners or bleach.