Lee & Plumpton Crescent User manual

No. 110 A/1879 Revision A 10/10/2018 1
www.leeandplumpton.co.uk
ASSEMBLY INSTRUCTIONS
RANGE Duty, Crescent with or without Modesty.
REF: 1600mm, 1800mm
Read this leaet before
assembly
2 People
Required
COMPONENT PARTS
Crescent with Modesty shown.
Item 1
Crescent Top Panel
Qty 1
Item 9 & 10
Cable Port
Qty 4
A/0525 & A/0527
Item 12
Expander Plate
Qty 4
A/1164
Item 13 *
Modesty Panel Spacer
Qty 15
R/0071
Item 14 *
Minix Bolt Chipfast
34 x 15
Qty 7
F/0508
Item 15 *
Minix M6
Qty 8
F/0433
Item 16 *
Minix Alloy Cams
18mm
Qty 15
F/0434
Item 17 *
Cam Cover
Qty 15
F/0436 F/0446 F/0545
F/0575 F/0576 F/0577
Item 18
Rail Screw
Qty 12
F/0587
Item 19
Grub Screws M8
Qty 8
F/0637
Item 20
5/8” x 8g Pan Pozi BZP
Qty 4
F/0414
Item 21
5mm Hole Plugs
Qty 8
A/0518, A/0763,
F/0546
Item 2 *
Modesty Panel
Qty 1
Item 3 *
Short Modesty Panel
Qty 1
Item 4
GoalPost Frame RH
Qty 1
Item 5
GoalPost Frame LH
Qty 1
Item 6
Back Coner Leg
Qty 1
Item 7
Rail
Qty 2
Item 8
Short Rail
Qty 2
* Desk with Modesty Panel only.

No. 110 A/1879 Revision A 10/10/2018 2
STEP 1
ASSEMBLY INSTRUCTIONS
STEP 2
TOOLS REQUIRED BEFORE YOU BEGIN...
• Check you have all the tools and components required
• Keep children and animals away from small parts
• Ensure you have adequate space
• Assemble product on a at, clean surface
• Apply manual handling guidelines when building this item
• Pozi head screwdriver
• 4mm Allen Key
STEP 3
Note the position of the
notch in the end of the
Rails – for positioning
Leg at step 4.
Lay the Top (1) upside down on a
at, soft surface.
Ensure all holes are free of debris.
Screw the Rails (7) & (8) onto the
Top with Screws (18).
18
1
Prepare the “goalpost” Leg
(4,5) by placing the Expander
Plates(12) into the brackets.
If the desk is to have a Modesty
Panel, screw the Minix bolts (15)
into the holes in the Legs.
Place the Spacers (13) over the
Bolts.
If no Modesty Panel is to be tted,
ll the holes with the 5mm Hole
Plugs (21).
If a Modesty Panel is to be tted,
screw the Minix Bolts (15) into
the holes in the Back Corner
Leg(6). Place the Spacers (13)
over the Bolts.
Screw the Minix Bolts (14) into
the Top. Place the Spacers (13)
over the Bolts.
8
7
15
13
12
6
13
15
14
13
45
+

No. 110 A/1879 Revision A 10/10/2018 3
ASSEMBLY INSTRUCTIONS
STEP 4
STEP 5
STEP 6
If a modesty panel is to be tted,
place Cams (16) in the holes in the
Modesty Panels (2) & (3).
Ensure the arrow on the Cam
points to the edge of the panel.
Fit the Modesty Panels onto the
Bolts/Spacers in the Leg and lock
the Cams with just over a half
turn.
Carefully place the assembled
Leg/Modesty Panels onto the
Bolts/Spacers in the Top.
Lock the Cams with just over half
a turn.
Screw the Leg to the Top with
Screws (20), only using the two
accessible screw holes.
If no Modesty Panel is to be tted,
screw the Leg to the Top with
Screws (20), using all 4 holes to
attach the Leg.
16
2
3
20
20

No. 110 A/1879 Revision A 10/10/2018 4
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
STEP 7
STEP 8
STEP 9
Clean using a damp cloth and mild detergent – do not use abrasive cleaners or bleach.
Slide the brackets on the
Legs(4,5) into the open notched
ends of the Rails screwed to the
Top.
If a Modesty Panel is attached,
ensure that the Bolts in the Leg
are aligned with the appropriate
holes in the Modesty Panel.
Lock the Cams with just over half
a turn.
Screw the Grub Screws (19) into
the Expander Plate through the
hole in the Rail.
Tighten the Grub Screws until the
Expander Plate is pushed tight to
the inside of the Rail.
Carefully turn the Desk upright.
Fit the Cable Ports (9) and
Covers(10).
Adjust the Feet to level the Desk.
Fit the Cam Cover Caps (17)
4
5
10
17
9