Lee & Plumpton Libra Desk User manual

1
No.120 A/2129 Revision A 15/08/2018
COMPONENT PARTS
www.leeandplumpton.co.uk
ASSEMBLY INSTRUCTIONS
RANGE Libra Desk.
REF: 1200, 1400, 1600mm Wide.
Read this leaet before
assembly
2 People
Required
FIXINGS
Item 1
M/0834 M/0835
LH End Goalpost
Item 4
F/0561
M6x10mm Socket Head
Screw
Item 5
F/0655
M6 Lock Washer
Item 6
F/0433
Minix Bolt M6
Item 7
F/0419
5/8” x 8G Posi
Flange Black Screw
Item 11
F0532
Minix Bolt
Chipfast
Item 12
F.0436, F.0446, F.0545
F.0575, F.0576, F.0577
Cam Cover
Item 13
A/1165
Cable Port
Item 15
F/0414
5/8” Pan Posi Bzp Screw
Item 2
M/0832 M/0833
RH End Goalpost
Item 3
NP10_0050
End Goalpost Inll
Item 9
Modesty Panel
Item 14
Cable Tray (Optional Item)
Item 8
M/0830 M/0831
Intermediate Goalpost
Item 10
Top Panel, Rail Assembly

2
No.120 A/2129 Revision A 15/08/2018
TOOLS REQUIRED BEFORE YOU BEGIN...
• Check you have all the tools and components required
• Keep children and animals away from small parts
• Ensure you have adequate space
• Assemble product on a at, clean surface
• Apply manual handling guidelines when building this item
• Pozi head screwdriver
• 5mm Allen key
STEP 1
ASSEMBLY INSTRUCTIONS
STEP 2
FIXINGS QUANTITIES BY PACK
3
Fit the Inll Panels (3) to the End
Goalpost (1,2) using the Black
Posi Flange Screws (7). Ensure
that there is a 3mm gap all around
the Inll Panel.
Screw the Minix Bolt M6’s (6) into
the End Goalposts (1,2) and the
Intermediate Goalposts (8).
Please note that single desks
do not require an Intermediate
Goalpost.
1
7
6
1
6
8
Packs Item 4 Item 5 Item 6 Item 7 Item 11 Item 12 Item 13 Item 15
Desk End Goalposts Double Pack 2 2 2 6
Bench Intermediate Goalpost Single Pack 2 2 4
Top, Modesty Panel & Rail Pack (Desk) 372
Cable Trays 4

3
No.120 A/2129 Revision A 15/08/2018
ASSEMBLY INSTRUCTIONS
STEP 4
STEP 5
STEP 3
Ensure that the Cams in the
Modesty Panel (9) have the
moulded-in arrow feature pointing
to the edge of the Panel.
Ensure the Cams face into the
space between the Goalposts, as
shown. Attach the Modesty Panel
(9) to the End Goalpost (1,2).
Fit the panel over the Minix Bolts
M6 (6) and lock the Cams in the
Modesty Panel with a half-turn.
If required, connect the
Intermediate Goalpost (8) to the
Modesty Panel (9) by engaging
the Minix Bolts M6 (6) into the
holes in the Modesty Panels (8).
Lock the Cams with a half-turn.
9
1
1
9
8
Ensure that the M6x10mm Socket
Head Screw (4) and the M6 Lock
Washer (5) are unscrewed as
far as possible whilst still being
attached to the Goalposts.
This is to allow space for the ends
of the Rails on the Top Panel &
Rails Assembly (10) to engage
with the Goalposts.
54

4
No.120 A/2129 Revision A 15/08/2018
ASSEMBLY INSTRUCTIONS
STEP 7
STEP 8
STEP 6
If required, t the Cable Tray(14)
to the Modesty Panel (9),
using the 5/8” Pan Posi BZP
Screws(15) in the pilot holes.
Screw the Minix Bolt Chipfasts(11)
into the rearmost set of holes in the
underside of the Top Panel & Rail
Assembly (10).
15
14
10
11
Once the rst two Goalposts (1,2)
have been connected by Modesty
Panels (9) they are freestanding.
Extra sections can now be added
onto the desk in the same way as
described in Steps 4 and 5.
9
2

5
No.120 A/2129 Revision A 15/08/2018
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
STEP 10
STEP 9
Clean using a damp cloth and mild detergent – do not use abrasive cleaners or bleach.
Fit the Cable Ports (13) into the
Top Panels. 13
Lower the Top Panel & Rail
Assemblies (10) onto the
assembled frame. Lock the Cams
in the Modesty Panel (9). Tighten
up the M6x10mm Socket Head
Screws (4) at the front of each
Goalpost to lock the Rails into
position.
Fit the Cam Covers (12).
10
9
4