Lee & Plumpton Duty 1200mm User manual

No. 111 A/1880 Revision A 10/10/2018 1
www.leeandplumpton.co.uk
ASSEMBLY INSTRUCTIONS
RANGE Duty, Delta with and without Modesty
REF: 1200mm
Read this leaet before
assembly
2 People
Required
COMPONENT PARTS
Delta with modesty shown.
Item 1
Top Panel
Qty 1
Item 2 *
Delta Mod Panel LH
Qty 1
Item 21
Short Rail
Qty 2
Item 3 *
Delta Mod Panel RH
Qty 1
Item 6
Back Corner Leg
Qty 1
Item 22
Rail
Qty 2
Item 8 & 9
Cable Port
Qty 4
A/0525 & A/0527
Item 11
Rail Screw
Qty 12
F/0587
Item 12
Expander Plate
Qty 4
A/1164
Item 13
Grub Screws M8
Qty 8
F/0637
Item 14 *
Minix Bolt Chipfast
34 x 15
Qty 8
F/0508
Item 15 *
Minix M6
Qty 4
F/0433
Item 16 *
Minix Alloy Cams
18mm
Qty 10
F/0434
Item 17 *
Cam Cover
Qty 10
F/0436 F/0446 F/0545
F/0575 F/0576 F/0577
Item 18
5/8” x 8g Pan Pozi
BZP
Qty 10
F/0414
Item 19 *
Modesty Panel
Spacer
Qty 10
R/0071
Item 20 *
12mm X M6
Mushroom Head Bolt
Qty 4
F/0441
Item 23
Rail Bung For Delta
Desks
Qty 4
NP4/1177
Item 24
5mm Hole Plugs
Qty 4
A/0518, A/0763,
F/0546
Item 4
GoalPost Frame RH
Qty 1
Item 5
GoalPost Frame LH
Qty 1
Item 7 *
Delta Back Leg
Bracket
Qty 2
* Desk with Modesty Panel only.

No. 111 A/1880 Revision A 10/10/2018 2
STEP 1
ASSEMBLY INSTRUCTIONS
STEP 2
TOOLS REQUIRED BEFORE YOU BEGIN...
• Check you have all the tools and components required
• Keep children and animals away from small parts
• Ensure you have adequate space
• Assemble product on a at, clean surface
• Apply manual handling guidelines when building this item
• Pozi head screwdriver
• 4mm Allen Key
STEP 3
Lay the Top (1) upside down on a
at, soft surface. Ensure all holes
are free of debris.
Lay the Rails (21) and (22) on the
Top. The shorter Rails are nearest
the front of the desk.
Screw the Rails onto the Top with
Screws (11).
Add Bungs (23) to the ends of the
rails near the middle of the top. 21
22
11
1
Screw the Back Corner Leg (6) to
the Top with Screws (18).18
6
23
Prepare the “goalpost”
Legs (4,5) by placing the Expander
Plates (12) into the brackets.
If the desk is to have a Modesty
Panel, screw the Minix bolts (15)
into the holes in the Legs.
Place the Spacers (19) over the
Bolts.
If no Modesty Panel is to be tted,
ll the holes with the 5mm Hole
Plugs (24).
15
12
4 5
+
19
Note the position of the
notch in the end of the
Rails – for positioning
Leg at step 6

No. 111 A/1880 Revision A 10/10/2018 3
ASSEMBLY INSTRUCTIONS
STEP 4
STEP 5
STEP 6
If a Modesty Panel is to be tted,
screw the Minix Bolts (14) into
the Top. Place the Spacers (19)
over the Bolts.
If a Modesty Panel is tted, place
Cams (16) in the holes in the
Modesty Panels (2) & (3).
Ensure the arrow on the Cam
points towards the edge of the
panel.
Carefully place the Modesty Panel
over the Bolts/Spacers in the Top.
Attach Leg Bracket (7) to Centre
Back Leg (6) using screws (20).
Attach the Leg Brackets to the
Modesty Panels with Screws (18).
Slide the brackets on the Legs
into the open notched ends of the
Rails screwed to the Top.
If a Modesty Panel is attached,
ensure that the Bolts in the Leg
are aligned with the appropriate
holes in the Modesty Panel.
Lock the Cams with just over half
a turn.
19
14
6
20 3
2
16
18
7

No. 111 A/1880 Revision A 10/10/2018 4
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
STEP 7
STEP 8
Clean using a damp cloth and mild detergent – do not use abrasive cleaners or bleach.
Screw the Grub Screws (13) into
the Expander Plate through the
hole in the Rail.
Tighten the Grub Screws until the
Expander Plate is pushed tight to
the inside of the Rail.
Fit the Cam Cover Caps (17).
Carefully turn the Desk upright.
Fit the Cable Ports (8) and
Covers (9).
Adjust the Feet to level the Desk.
9
8
13
17