Lennox BELLA-PK-TB User manual

HEARTH PRODUCTS
KITS AND ACCESSORIES
506033-11
REV. NC 12/2008
INSTALLATION INSTRUCTIONS FOR DECORATIVE TRIM
PANEL KITS FOR USE WITH THE BELLA™ PELLET STOVE
STONE PANEL KITS
BELLA™
1
Figure 2
Cat. # Model Description
H3485 BELLA-PK-TB Stone Panel Kit, Tan Brown
H3488 BELLA-PK-GV Stone Panel Kit, Gallo Veneziano
H3491 BELLA-PK-SS Stone Panel Kit, Beatrice Soapstone
KIT CONTENTS (See Figure 1)
2 ea. Side Panels (9-1/8” x 17-1/4” item #1)
1 ea. Front Panel (15-5/8” x 4-7/8” item #2)
2 ea. Protective Tape
1 ea. Instruction Sheet
GENERAL INFORMATION
All of these parts may scratch or break, great care should be used in
handling them.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact you local distributor
or dealer. Read this instruction sheet in its entirety before beginning the
installation. Failure to understand and follow these directions may result
in damage to the stone panels.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OP-
ERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE
INSTRUCTIONS.
TURN OFF THE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE
PROCEEDING.
IMPORTANT NOTE: Failure to follow these steps may result in damage
to the enamel or painted surfaces as well as the stone.
INSTALLATION INSTRUCTIONS
Step 1. Apply protective tape to the front edge of the right side door, and
the back (right) edge of the front door (see A in Figure 3).
Step 2. Locate the two right side door retaining screws (see Figure 2).
Step 3. Using a 5/32” allen wrench and a 3/8” open end wrench remove
the two screws from the right side door. Note: the screws do not
have to be completely removed from the stove body, only the
right side door.
1
2
Figure 1 - Kit Contents
DRAFT
12/15/2008
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
TOOLS NEEDED
1/8” Allen Wrench
5/32” Allen Wrench
3/8” Open End Wrench

Printed in U.S.A. © 2008 Lennox Hearth Products
P/N 506033-11 REV. NC 12/2008
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and the discontinuance of colors, styles and products. Consult
your local distributor for fireplace code information.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
2
Step 3. Hold the right side door closed tightly while you carefully return the
front cast iron door to the closed position, paying special attention
to the narrow gap between the two doors (A in Figure 3).
Figure 3
Step 4. With the side door open, using your 1/8” allen wrench, remove the
screws attaching the top side panel bracket and set aside for step 6.
Step 5. Loosen the screws attaching the lower panel bracket enough to
remove the sheet metal panel. With bracket still loose, place the
stone panel between the bracket and door.
Step 6. Hold new stone panel in place while reattaching the upper side
panel bracket. Snug down upper and lower screws taking care not
to over-tighten.
CAUTION: OVER-TIGHTENING THE PANEL BRACKETS MAY RE-
SULT IN DAMAGE, CRACKS ETC TO THE STONE PANELS. SNUG
ONLY!
Step 7. Repeat step 6 on opposing side.
Step 8. To re-secure right side door, make sure the front cast iron door is
fully closed, close the right side door and while holding it tightly
shut carefully open the front door again and re-secure right side
door to the firebox (see Figure 2). Once secure, check the clearance
between the front and side castings by carefully opening the front
door, adjust the side door screws accordingly.
Step 9. When you are finished installing the panels in the sides, repeat the
same sequence on the front door. Do not over tighten!
Figure 4
Figure 5
DO NOT OVERTIGHTEN SCREWS! SNUG ONLY!
1110 West Taft Avenue • Orange, CA 92865
DO NOT OVERTIGHTEN SCREWS! SNUG ONLY!
A