LIVARNO LUX 288404 Technical specifications

LED OUTDOOR SPOTLIGHT 8.5W
IAN 288404
LED-AUSSENSTRAHLER 8,5W
Montage-, Bedienungs- und Sicherheitshinweise
LED OUTDOOR SPOTLIGHT 8.5W
Assembly, operating and safety instructions
UDENDØRS LED-PROJEKTØR 8,5W
Monterings-, betjenings- og sikkerhedshenvisninger
PROJECTEUR EXTÉRIEUR LED 8,5W
Instructions de montage, d‘utilisation et
consignes de sécurité
LED-BUITENSCHIJNWERPER 8,5W
Montage-, bedienings- en veiligheidsinstructies

LED OUTDOOR SPOTLIGHT 8.5W
GB/IE/ NI Assembly, operating and safety instructions Page 5
DK Monterings-, betjenings- og sikkerhedshenvisninger Side 15
FR/BE Instructions de montage, d‘utilisation et consignes de sécurité Page 25
NL/BE Montage-, bedienings- en veiligheidsinstructies Pagina 36
DE/AT/CH Montage-, Bedienungs- und Sicherheitshinweise Seite 47

B
12
11
10
A
6
7
9
4
1 2
3
5
8

2.5 m
D
C
13
14

5GB/IE/NI
List of pictograms used..................................................Page 6
Introduction.............................................................................Page 6
Intended use..................................................................................Page 6
Parts description............................................................................Page 6
Technical Data ..............................................................................Page 7
Scope of delivery..........................................................................Page 7
General safety instructions........................................Page 7
Before installation.............................................................Page 9
Before use.................................................................................Page 9
Installation...............................................................................Page 9
Start-up .......................................................................................Page 11
Adjusting the motion detector.......................................................Page 11
Setting the lighting duration..........................................................Page 11
Adjusting the sensitivity of the sensor...........................................Page 11
Setting the daylight level ..............................................................Page 12
Aligning the motion detector........................................................Page 12
Cleaning and Care.............................................................Page 13
Disposal......................................................................................Page 13
Warranty...................................................................................Page 13

6 GB/IE/NI
List of pictograms used
Alternating current Motion sensor cover-
age distance: 12m
Splashproof LED illuminating
angle: 105 deg
Motion sensor detection
angle: 180 deg LED lifespan
LED Outdoor Spotlight
8.5W
Introduction
We congratulate you on the pur-
chase of your new product. You
have chosen a high quality product.
The instructions for use are part of
the product. They contain important
information concerning safety, use
and disposal. Before using the prod-
uct, please familiarise yourself with
all of the safety information and
instructions for use. Only use the
product as described and for the
specified applications. If you pass
the product on to anyone else,
please ensure that you also pass
on all the documentation with it.
Intended use
The product is intended for auto-
matic lighting in both indoor and
outdoor areas. This product is solely
intended for private use.
Parts description
1Spotlight
2Spring washer
3Metal Nut
4Mounting stirrup
5Locking screw

7GB/IE/NI
6Connection box
7Cable gland
8Fastening screws
9Motion detector
10 Rotary control SENS (sensitivity)
11 Rotary control TIME (switched
on duration)
12 Rotary control LUX (light
sensitivity)
13 Terminal block
14 Cable clamp
Technical Data
Operating voltage: 230 V∼ 50Hz,
8.5W
LEDs: 16 x LED x
0.5W
Dimming switch: Adjustable
from 10lx–
20,000lx
Light on time: Adjustable
between
approx.10 s –
4min
Protection class: I
Protection class: IP44
(Splashproof)
Dimensions
(H x W x D): approx. 197 x
149 x 121mm
Projected area: max. 190 x
149mm
Mounting height: approx. 2.5 m
Weight: approx. 640 g
Scope of delivery
1 LED Spotlight with motion
detector
2 Wall plugs (Ø 6mm)
2 Screws
1 Set of mounting and operating
instructions
General safety
instructions
Before using the product, please
familiarise yourself with all of the
safety information and instructions
for use! When passing this product
on to others, please also include
all the documents!

8 GB/IE/NI
DANGER TO LIFE
AND ACCIDENT
HAZARD FOR
TODDLERS AND SMALL
CHILDREN! Never leave chil-
dren unattended with the pack-
aging material. The packaging
material represents a danger of
suffocation. Children frequently
underestimate the dangers.
Please keep children away
from the product at all times.
This product may be used by
children age 8 years and up,
as well as by persons with re-
duced physical, sensory or
mental capacities, or lacking
experience and/or knowledge,
so long as they are supervised
or instructed in the safe use of
the product and understand
the associated risks. Children
should not be allowed to play
with the product. Cleaning and
user maintenance should not
be performed by children with-
out supervision.
Risk of electric
shock
Always check product for dam-
age before connecting it to
power. Never use the product
if it shows any signs of damage.
Prior to installation, verify that
the mains voltage on site corre-
sponds with the operating volt-
age required for the product
(230V∼ 50Hz). Otherwise do
not install the product.
CAUTION! DANGER OF
BURN INJURIES! To prevent
burns, verify the product is
switched off and has cooled
down for at least 15min before
touching it. The product can
become very hot.
0.5m
FIRE HAZARD!
Fit the product so
that it is at least
0.5m away from the material
to be illuminated. Excessive
heat can result in a fire.
CAUTION! RISK
OF INJURY! Bro-
ken lamp glass must
be replaced before any further
use is made of the product.

9GB/IE/NI
Only intended for installations
out of normal reach.
This product does not contain
any parts that can be serviced
by the user. The LEDs cannot
be replaced by end user.
If the LEDs fail at the end of their
lives, they must be repaired by
qualified electrician or the en-
tire product must be replaced.
The spotlight is only suited for
use with the built-in LED control
gear.
The product continues to draw
a small amount of power even
if the lamp is off as long as
product is connected to supply
mains. To switch the product
off completely, the mains switch
should be switched off.
Before installation
Important: The electrical con-
nection must be established by a
qualified electrician or a person
trained to perform electrical instal-
lations. This person must be familiar
with the properties of the product
and the connection regulations.
Before installation ensure that
the circuit, to which the product
will be connected, is not ener-
gised. To do so, remove the fuse
or switch off the circuit breaker
in the fuse box (0 position).
Use the voltage tester to verify
the de-energised status.
The included mounting material
is suitable for ordinary solid
concrete or masonry construc-
tion. Check which mounting
material is suitable for your
chosen mounting surface. If
necessary, seek expert advice.
Before use
Note: Remove all packaging
materials from the product.
Installation
Make sure you will not be drill-
ing into electrical, gas or water
lines inside the wall. Use a
power drill to drill the holes into
the brick wall. Always observe
all safety instructions for the

10 GB/IE/NI
power drill in the manual for
the power drill. Death or injury
due to electric shock may
otherwise result.
When selecting the mounting loca-
tion, pay attention to the following:
Make sure that the spotlight 1
illuminates the desired area.
You can move the spotlight 1
vertically.
Make sure the motion detector
9covers the desired area.
The motion detector 9has a
maximum coverage range of
12m, with a coverage angle
of about 180° (depending on
the mounting height – a height
of 2.50m is ideal) (Fig. D).
Make sure the motion detector
9is not illuminated at night
by street lighting. This can influ-
ence its functioning.
During mounting, proceed as
described below:
Unscrew locking screw 5by
using a screw driver (cross
type) to detach the mounting
stirrup 4from the spotlight 1.
Hold the mounting stirrup 4
so that it is horizontal (possibly
with a spirit level) against the
wall and mark the fastening
holes.
Now drill the fastening holes
(Ø 6mm) and push the wall
plugs into the drill holes (Fig. A).
Secure the mounting stirrup 4
onto the wall using the screws
provided.
Now use the screw driver (cross
type) to attach the spotlight 1
to the mounting stirrup 4by
using the previously removed
locking screw 5, spring washer
2, and metal nut 3(Fig A).
Open the connection box 6
after you have released the lid
of the connection box 6with
a cross type screwdriver.
Insert the connection cable (not
include in the product), type
H05RN-F 3G 1.0mm2 , through
the cable gland 7and into
the connection box 6. The
length for the connection cable
line should not exceed 2.5 m.
Fix the connection cable with
the cable clamp 14 first and

11GB/IE/NI
then by turning the nut of the
cable gland 7.
Connect the lead of the cable
with the terminal block 13 in
the connection box 6. Pay at-
tention to the markings on the
terminal block 13 (L for live, N
for neutral and for the earth
wire) (Fig. C).
Close the connection box 6.
Align the spotlight 1into the
desired direction. For this, you
may need to slacken the fasten-
ing screws 8. After finish the
alignment, tighten the fastening
screws 8again, to ensure a
secure hold.
Reinsert the fuse or switch the circuit
breaker back on. Your product is
now ready to use.
Start-up
Adjusting the
motion detector
Depending on the pre-adjustments
of the motion detector 9, the spot-
light 1will switch itself on for a
certain period of time as soon as
the motion detector 9detects
movement. These pre-adjustments
are made using the three controllers
on the underside of the motion
detector 9(Fig. B).
Setting the
lighting duration
Turn the rotary control TIME 11
clockwise to increase the dura-
tion of the illumination. The
lighting duration can be adjusted
within a time window of approx.
10 seconds to 4 minutes.
Adjusting the sensi-
tivity of the sensor
Turn the rotary control SENS 10
clockwise to increase the sensi-
tivity of the sensor.
Note: The motion detector 9
responds to heat radiation.
When outdoor temperatures
are low, it is more sensitive to
body heat than when outdoor
temperatures are warm. Be

12 GB/IE/NI
sure to regulate the sensitivity
of the sensor over the course
of the year.
Setting the
daylight level
Turn the rotary control LUX 12
to increase the daylight level:
In the position, the motion
detector only reacts at night
(at approx. 10 lx). In the
position, the motion detector
also responds at daylight levels,
as long as about 20,000lx
are not exceeded.
Aligning the
motion detector
Note: Perform this adjustment at
twilight.
Slacken the locking screw 8.
Turn the rotary control LUX 12
to position .
Align the motion detector 9
into the central region of the
desired coverage area.
Move about through the cover-
age area until you are satisfied
with the response characteris-
tics of the motion detector 9.
To find the proper orientation,
change the position of the rotary
control SENS 10 or the orienta-
tion of the motion detector 9.
Note: Please note that the
motion detector 9primarily
detects movements transverse
to the motion detector 9. If
you move directly towards the
motion detector 9, it cannot
detect this movement.
When you have aligned the
motion detector 9satisfacto-
rily, re-tighten the fastening
screws 8to fix the adjustment.
Turn the rotary control LUX 12
to the desired position. These
can be determined during the
dawn or twilight hours during
which the spotlight 1should
respond.
Slowly turn the rotary control
LUX 12 clockwise until it reacts
to movement within the cover-
age area.

13GB/IE/NI
Cleaning and Care
Before cleaning, remove the
fuse or switch off the circuit
breaker at the fuse box.
Never immerse the product in
water or other liquids. Otherwise
the product can be damaged.
Clean the product with a lint-free,
slightly moist cloth and mild
cleaning agent.
Reconnect the fuse or circuit
breaker for use after cleaning.
Disposal
The packaging is made
entirely of recyclable
materials, which you may
dispose of at local recycling facilities.
The Green Dot is not valid for Ger-
many.
b
a
Observe the marking of
the packaging materials
for waste separation,
which are marked with abbreviations
(a) and numbers (b) with following
meaning: 1–7: plastics/20–22:
paper and fibreboard/80–98:
composite materials.
The product and pack-
aging materials are re-
cyclable, dispose of it
separately for better waste treat-
ment. The Triman logo is valid in
France only.
Contact your local refuse
disposal authority for
more details of how to
dispose of your worn-out product.
To help protect the envi-
ronment, please dispose
of the product properly
when it has reached the end of its
useful life and not in the household
waste. Information on collection
points and their opening hours can
be obtained from your local authority.
Warranty
The product has been manufactured
to strict quality guidelines and m eticu-
lously examined before delivery.
In the event of product defects you

14 GB/IE/NI
have legal rights against the retailer
of this product. Your legal rights are
not limited in any way by our war-
ranty detailed below.
The warranty for this product is 3
years from the date of purchase.
Should this product show any fault
in materials or manufacture within
3 years from the date of purchase,
we will repair or replace it – at our
choice – free of charge to you.
The warranty period begins on the
date of purchase. Please keep the
original sales receipt in a safe loca-
tion. This document is required as
your proof of purchase. This war-
ranty becomes void if the product
has been damaged, or used or
maintained improperly.
The warranty applies to defects in
material or manufacture. This war-
ranty does not cover product parts
subject to normal wear, thus pos-
sibly considered consumables (e.g.
batteries) or for damage to fragile
parts, e.g. switches, rechargeable
batteries or glass parts.

15DK
De anvendte piktogrammers legende............. Side 16
Indledning ................................................................................ Side 16
Formålsbestemt anvendelse ......................................................... Side 16
Beskrivelse af de enkelte dele...................................................... Side 16
Tekniske data................................................................................. Side 17
Leverede dele................................................................................ Side 17
Generelle sikkerhedshenvisninger..................... Side 17
Inden monteringen........................................................... Side 19
Inden ibrugtagningen .................................................... Side 19
Montage..................................................................................... Side 19
Ibrugtagning.......................................................................... Side 21
Indstilling af bevægelsessensor.................................................... Side 21
Indstilling af lysetid........................................................................ Side 21
Indstilling af sensorens følsomhed................................................ Side 21
Indstilling af dagslysniveau .......................................................... Side 21
Indstilling af bevægelsessensoren................................................ Side 22
Rengøring og pleje ........................................................... Side 22
Bortskaffelse.......................................................................... Side 23
Garanti........................................................................................ Side 23

16 DK
De anvendte piktogrammers legende
Vekselstrøm Registreringsafstand
bevægelsessensor
12 m
Sprøjtevandsbeskyttet Belysningsvinkel LED:
105°
Registreringsvinkel be-
vægelsessensor: 180° LED-levetid
Udendørs LED-projektør
8,5 W
Indledning
Hjerteligt tillykke med købet af deres
nye produkt. Du har besluttet dig for
et produkt af høj kvalitet. Brugervej-
ledningen er en del af dette produkt.
Den indeholder vigtige informationer
om sikkerhed, brug og bortskaffelse.
Gør dig inden ibrugtagning af pro-
duktet fortrolig med alle betjenings-
og sikkerhedsanvisninger. Benyt kun
produktet som beskrevet og til de
oplyste formål. Videregiv alle papirer,
hvis du giver produktet videre til
tredjemand.
Formålsbestemt an-
vendelse
Produktet er egnet til automatisk
belysning inden- og udendørs.
Produktet er udelukkende beregnet
til privat anvendelse.
Beskrivelse af de
enkelte dele
1Spot
2Fjederskive
3Metalmøtrik
4Montagebøjle
5Låseskrue
6Tilslutningsboks
7Kabelforskruning

17DK
8Stopringsskruer
9Bevægelsessensor
10 Drejeregulator SENS
(følsomhed)
11 Drejeregulator TIME (driftstid)
12 Drejeregulator LUX
(lysfølsomhed)
13 Tilslutningsanordning
14 Kabelklemme
Tekniske data
Driftsspænding: 230 V∼ 50Hz,
8,5W
LED´er: 16 x LED à 0,5W
Dæmpnings-
kontakt: kan indstilles fra
10lx- 20.000lx.
Lysetid: kan indstilles fra
ca. 10s - 4min.
Bskyttelsesklasse: I
Beskyttelsesart: IP 44 (beskyttet
mod vand)
Mål (HxBxD): ca. 197 x 149 x
121mm
Projektionsflade: max. 190 x
149mm
Montagehøjde: ca. 2,5m
Vægt: ca. 640g
Leverede dele
1 LED-udendørs spot med
bevægelsessensor
2 rawplugs (Ø 6mm)
2 skruer
1 montage- og
betjeningsvejledning
Generelle
sikkerheds-
henvisninger
Gør Dem fortrolig med alle betje-
nings- og sikkerhedshenvisninger,
inden produktet bruges for første
gang! Hvis De giver produktet vi-
dere til tredjemand, så skal alt ma-
teriale også følge med!
LIVS- OG ULYK-
KESFARE FOR
SMÅBØRN OG
BØRN! Lad aldrig børn være
uden opsyn med emballagen.
Børn kan kvæles i emballage-
materialet. Børn undervurderer
hyppigt farerne. Hold altid
børn på afstand fra produktet.

18 DK
Dette produkt kan benyttes af
børn fra 8-årsalderen og opad,
samt af personer med forrin-
gede fysiske, følelsesmæssige
eller mentale evner eller man-
gel på erfaring og viden, når
de er under opsyn eller er ble-
vet vejledt med hensyn til pro-
duktet og forstår de deraf resul-
terende farer. Børn må ikke
lege med produktet. Rengøring
og brugervedligeholdelse må
ikke gennemføres af børn uden
at de er under opsyn.
Livsfare grundet
elektrisk stød
Kontroller produktet inden hver
strømtilslutning for eventuelle
beskadigelser. Anvend ikke
produktet, når der er beskadi-
gelser.
Kontrollér inden montagen, at
den tilstedeværende netspæn-
ding stemmer overens med
produktets nødvendige drift-
spænding (230V∼ 50Hz).
Montér ikke produktet, når
dette ikke er tilfældet.
ADVARSEL! FARE FOR
FORBRÆNDING! Kontrollér
at produktet er slukket og har
kølet af i mindst 15 min., inden
du rører ved det. Produktet kan
udvikle en stor varme.
0,5m
BRANDFARE!
Montér produktet
med en afstand af
mindst 0,5m til materialer, der
oplyses af den. For kraftig var-
meudvikling kan medføre
brand.
ADVARSEL!
FARE FOR TIL-
SKADEKOMST!
Et beskadiget lampeglas skal
erstattes, inden lampen bruges
igen.
Kun beregnet til installering
udenfor rækkevidde.
Denne artikel indeholder ingen
dele, som kan vedligeholdes af
forbrugeren. LED´erne kan ikke
udskiftes af brugeren.
Hvis lyskilden i slutningen af
dens levetid svigter, skal hele
produktet erstattes.
Hvis LEDérne i slutningen af
deres levetid svigter, skal de
repareres af en uddannet

19DK
elektriker ellers skal produktet
bortskaffes.
Så længe produktet er tilsluttet
en stikdåse, så bruger det lidt
strøm - også når produktet er
slukket. For at slukke helt for
produktet, bør afbryderen
slukkes.
Inden monteringen
Vigtig: den elektriske tilslutning
skal ske gennem en uddannet elek-
triker eller en person der har erfa-
ring med elektriske installationer.
Denne person skal have kendskab
til produktet og bestemmelserne for
tilslutningen.
Sørg inden installeringen for,
at der ved ledningen, som pro-
duktet skal tilsluttes til, ikke er
nogen spænding. Fjern sikrin-
gen hertil, eller slå effektafbry-
deren i omskiftertavlen fra
(0 stilling).
Kontrollér tilslutningsstedet med
en spændingstester.
Det medfølgende montagema-
teriale er egnet til almindeligt,
fast murværk. Undersøg også
hvilket montagematerialer der
er egenet til den af Dem valgte
montageundergrund. Informér
Dem i givet fald hos en fagud-
dannet person.
Inden
ibrugtagningen
Bemærk: fjern alt emballage fra
produktet.
Montage
Kontrollér, at du ikke støder på
strøm-, gas- eller vandledninger,
når du borer i væggen. Læs i
boremaskinens betjeningsvej-
ledning og overhold alle sikker-
hedsanvisninger. Ellers er der
livsfare eller fare for tilskade-
komst gennem elektrisk stød.
Vær opmærksom på følgende for-
hold ved valget af montagestedet:
Kontrollér at spotten 1oply-
ser det ønskede område. Spot-
ten 1kan bevæges lodret.

20 DK
Kontrollér at bevægelsessenso-
ren 9registrerer det ønskede
område. Bevægelsessensoren
9
har et registreringsområde på
maks. 12m, med en registrer-
ingsvinkel på ca. 180° (af-
hængig af montagehøjden –
ideel er en højde på 2,50m)
(afbildning D).
Vær opmærksom på at bevæ-
gelsessensoren 9ikke belyses
af gadebelysningen om natten.
Dette kan påvirke funktionen.
Med hensyn til monteringen gør
som beskrevet i følgende:
Løsn låseskruen 5med en
stjerne-skruetrækker, for at
løsne montagebøjlen 4fra
spotten 1.
Hold montagebøjlen 4vand-
ret pladseret (brug i givet fald
vaterpas) mod væggen og
markér hullerne til fastgørelse.
Bor nu hullerne til fastgørelse
(Ø 6 mm) og før rawplugsene
ind i borehullerne (afbildning A).
Fastgør montagebøjlen 4
med de vedlagte skruer.
Fastgør herefter spotten 1til
montagebøjlen 4, idet du
skruer låseskruen 5, fjederski-
ven 2og metalmøtrikken 3
fast med stjerne-skruetrækkeren
(afbildning A).
Åbn tilslutningsboksen 6efter
at tilslutningboksens låg 6er
åbnet med en stjerneskrue-
trækker.
Før forbindelsesledningen (ikke
inkluderet i leveringen) af typen
H05RN-F 3G 1,0mm2gennem
kabelforskruningen 7ind i til-
slutningsboksen 6. Forbindel-
sesledningen må max. være
2,5m. Fiksér tilslutningskablet
først med kabelklemmen 14
og efterfølgende ved at dreje
kabelforskruningens 7møtrik.
Forbind forbindelsesledningen
med tilslutningsanordningen 13
i tilslutningsboksen 6. Vær
herved opmærksom på tilslut-
ningsanordningens 13 mærk-
ning (L for spændingsførende
leder, N for nullederen og
for beskyttelseslederen) (afbild-
ning C).
Luk tilslutningsboksen 6igen.
Indstil spotten 1i den ønskede
retning. Låseskruen 8skal i
givet fald løsnes lidt hertil.