LSIS XGL-EFMT User manual

Right choice for ultimate yield
LSIS strives to maximize customers' profit in gratitude of choosing us for your partner.
Programmable Logic Controller
XGT FEnet I/F Module
User’s Manual
 Read this manual carefully before
installing,
wiring, operating, servicing
or inspecting this equipment.

Keep this manual within easy reach
for quick reference.
XGL-EFMT
(B)
XGL-EFMF
(B)
XGL-EH5T
XGT Series
http://eng.lsis.biz

Safety Instructions
Before using the product …
For your safety and effective operation, please read the safety instructions
thoroughly before using the product. Safety Instructions should always be
observed in order to prevent accident or risk with the safe and proper use the
product.
Instructions are divided into “Warning” and “Caution”, and the meaning of the
terms is as follows.
This symbol indicates the possibility of serious injury
or death if some applicable instruction is violated
This symbol indicates the possibility of severe or
slight injury, and property damages if some
applicable instruction is violated
Moreover, even classified events under its caution category may develop
into serious accidents relying on situations. Therefore we strongly advise users
to observe all precautions properly just like warnings.
The marks displayed on the product and in the user’s manual have the
following meanings.
Be careful! Danger may be expected.
Be careful! Electric shock may occur.
The user’s manual even after read shall be kept available and accessible to
any user of the product.
Warning
Caution

Safety Instructions
Safety Instructions for design process
1. Please install a protection circuit on the exterior of PLC so that the
whole system may operate safely regardless of failures from
external power or PLC. Any abnormal output or operation from PLC
may cause serious problems to safety in whole system.
(1) Install protection units on the exterior of PLC like an interlock circuit
that deals with opposite operations such as
emergency stop,
protection circuit, and forward/reverse rotation or install an interlock
circuit that deals with high/low limit under its position controls.
(2) If any system error (watch-dog timer error, module installation error,
etc.) is detected during CPU operation in PLC, all output signals are
designed to be turned off and stopped for safety. However, there
are cases when output signals remain active due to device failures
in Relay and TR which can’t be detected
. Thus, you are
recommended to install an addition circuit to monitor the output
status for those critical outputs which may cause significant
problems.
2. Never overload more than rated current of output module nor
allow to have a short circuit. Over current for a long period time may
cause a fire .
3. Never let the external power of the output circuit to be on earlier
than PLC power, which may cause accidents from abnormal output or
operation.
4.
Please install interlock circuits in the sequence program for safe
operations in the system when exchange data with PLC or modify
operation modes using a
computer or other external equipments
Read specific instructions thoroughly when conducting control
operations with PLC.
Warning

Safety Instructions
Safety Instructions for design process
Safety Instructions on installation process
I/O signal or communication line shall be wired at least 100mm
away from a high-voltage cable or power line.Fail to follow this
instruction may cause malfunctions from noise
Caution
1. Use PLC only in the environment specified in PLC manual or
general standard of data sheet.
If not, electric shock, fire,
abnormal operation of the product may be caused.
2. Before install or remove the module, be sure PLC power is off.
If not, electric shock or damage on the product may be caused.
3. Be sure that every module is securely attached after adding a
module or an extension connector.
If the product is installed
loosely or incorrectly, abnormal operation, error or dropping may
be caused.
In addition, contact failures under poor cable
installation will be causing malfunctions as well.
4. Be sure that screws get tighten securely under vibrating
environments.
Fail to do so will put the product under direct
vibrations which will cause electric shock, fire and abnormal
operation.
5. Do not come in contact with conducting parts in each module,
which may cause electric shock, malfunctions
or abnormal
operation.
Caution

Safety Instructions
Safety Instructions for wiring process
1. Prior to wiring works, make sure that every power is turned off.
If not, electric shock or damage on the product may be caused.
2.
After wiring process is done, make sure that terminal covers
are installed properly before its use.Fail to install the cover may
cause electric shocks.
Warning
1. Check rated voltages
and terminal arrangements in each
product prior to its wiring process.
Applying incorrect voltages
other than rated voltages and misarrange
ment among terminals
may cause fire or malfunctions.
2. Secure terminal screws tightly applying with specified torque.If
the screws get loose, short circuit, fire or abnormal operation may be
caused.
Securing screws too tightly will cause damages to the
module or malfunctions, short circuit, and dropping.
3. Be sure to earth to the ground using Class 3 wires for FG
terminals which is exclusively used for PLC. If the terminals not
grounded correctly, abnormal operation or electric shock may be
caused.
4. Don’t let any foreign materials such as wiring waste inside the
module while wiring,
which may cause fire, damage on the
product or abnormal operation.
5. Make sure that pressed terminals get ti
ghten following the
specified torque. External connector type shall be pressed or
soldered using proper equipments.
Caution

Safety Instructions
Safety Instructions for test-operation and
maintenance
1. Don’t touch the terminal when powered
. Electric shock or
abnormal operation may occur.
2. Prior to cleaning or tightening the terminal screws, let all the
external power off including PLC power. If not, electric shock or
abnormal operation may occur.
3. Don’t let the battery recharged, disassembled, heated, short or
soldered. Heat, explosion or ignition may cause injuries or fire.
Warning
1. Do not make modifications or disassemble each module.Fire,
electric shock or abnormal operation may occur.
2. Prior to installing or disassemb
ling the module, let all the
external power off including PLC power. If not, electric shock or
abnormal operation may occur.
3. Keep any wireless equipment such as walkie-talkie or cell
phones at least 30cm away from PLC. If not, abnormal operation
may be caused.
4. When making a modification
on programs or using run to
modify functions under PLC operations, read and comprehend
all contents in the manual fully. Mism
anagement will cause
damages to products and accidents.
5. Avoid any physical impact to the battery and prevent it from
dropping as well. Damages to battery may cause leakage from its
fluid. When battery was dropped or exposed under strong impact,
never reuse the battery again. Moreover skilled workers are needed
when exchanging batteries.
Caution

Safety Instructions
Safety Instructions for waste disposal
Product or battery waste shall be processed as industrial waste.
The waste may discharge toxic materials or explode itself.
Caution

Revision History
2
Revision History
Version Date Remark Page
V1.0
2005.03
First Edition -
V1.1
2005.05
Adding the function description -
V1.2 2005.09 Adding module detachment and how to change Setting
PLC type at XG-PD
Adding appendix (CPU memory device)
CH3.8
CH5.2
APPENDIX-
V1.3
2005.11
Fixing figure and adding contents -
V1.4
2005.11
Fixing figure and contents -
V1.5 2008.07
1. Adding models
-adding XGI/XGR redundant system
-adding switch module (XGL-EH5T)
2. Adding E-mail service
3. Adding error code table
4. Adding CH 11 Compliance with EMC Specifications
5. Fixing headquarter address
CH1.3.2
CH7.6
CH10.4
CH11
Back cover-
V1.6 2009.09
1. Modifying Overview
2. Adding CPU
3. Adding contents on standard setting (One IP Solution,
DHCP)
CH1.2.1
CH1.3.2
CH5.3
V1.7 2011.05 1. How to enable link through flag added
2. Write_NC, Send_NC” instruction added CH5.5.2 CH7.2.1
V1.8 2013.10 1. Adding Communication load specifications
2. Changing Modbus server offset area CH2.2.3 CH8.3.1
V1.9 2014.03
1. Changing Communication load specifications
2. Adding info-U, iXP
3. Adding XGR HS Link
4. Adding XGT Dedicated Communication’s Header
5. Adding XGT Dedicated Communication’s error Code
6. Adding High Performance XGT
7. Changing error code table
CH2.2.3
CH4
CH6.6~6.7
CH8.1.2
CH8
CH9.2.3
CH10.4
V 2.0
2014.11
XG5000 V4.0 UI Update
-
V2.1
2016.10
XGL-EFMTB, XGL-EFMFB contents added
-
※The number of User’s manual is indicated right part of the back cover.
Copyright ⓒ2014 LSIS Co., Ltd All Rights Reserved.

About User’s Manual
1
Congratulations on purchasing PLC of LSIS Co.,Ltd.
Before use, make sure to carefully read and understand the User’s Manual about the functions, performances, installation and
programming of the product you purchased in order for correct use and importantly, let the end user and maintenance
administrator to be provided with the User’s Manual.
The User’s Manual describes the product. If necessary, you may refer to the following description and order accordingly. In
addition, you may connect our website (http://www.lsis.com/) and download the information as a PDF file.
Relevant User’s Manuals
Title Description
XG5000 User’s Manual XG5000 software user manual describing online function such as
programming, print, monitoring, debugging by using XGK, XGB
CPU
XG5000 User’s Manual
(for XGI, XGR)
XG5000 software user manual describing online function such
as programming, print, monitoring, debugging by using XGI,
XGRCPU
XGK/XGB Instructions & Programming
User’s Manual
User’s manual for programming
to explain how to use
instructions that are used PLC system with XGK, XGB CPU.
XGI/XGR Instructions & Programming
User’s Manual User’s manual for programming
to explain how to use
instructions that are used PLC system with XGI, XGR CPU.
XGK CPU User’s Manual
(XGK-CPUU/CPUH/CPUA/CPUS/CPUE/
CPUSN/CPUHN/CPUUN)
XGK-CPUU/CPUH/CPUA/CPUS/CPUE/CPUSN/CPUHN/
CPUUN user manual describing about XGK CPU module,
power module, base, IO module, specification of extension cable
and system configuration, EMC standard
XGI CPU User’s Manual
(XGI-CPUU/D,CPUU,CPUH,CPUS,CPUE,
CPUUN)
XGI-CPUU/D,CPUU,CPUH,CPUS,CPUE,CPUUN user manual
describing about XGICPU module, power module, base, IO
module, specification of extension cable and system
configuration, EMC standard
XGR redundant series User’s
Manual
XGR-CPUH/F, CPUH/T user manual describing about XGR
CPU module, power module, extension drive, base, IO module,
specification of extension cable and system configuration, EMC
standard
Currently user manual of FEnet I/F module is written based on the following version.
Related OS version list Item OS version
XGK-CPUU, CPUH, CPUA, CPUS, CPUE V4.55
XGI-CPUU/D, CPUU, CPUH, CPUS, CPUE V4.06
XGK-CPUSN, CPUHN, CPUUN V1.05
XGI-CPUUN V1.12
XGR-CPUH/F, CPUH/T, CPUH/S V2.72
XG5000 V4.10

◎
Table of Contents
◎
Chapter 1 Overview
1.1 Introduction ----------------------------------------------------------------------------------------------------- 1-1
1.2 Features of FEnet I/F Module -------------------------------------------------------------------------- 1-2
1.2.1 Characteristic of FEnet I/F module --------------------------------------------------------------- 1-2
1.2.2 Characteristic of XGL-EH5F (switch) ------------------------------------------------------------ 1-3
1.3 Product Configuration ---------------------------------------------------------------------- 1-4
1.3.1 Designation --------------------------------------------------------------------------------------------- 1-4
1.3.2 vailable units to be installed on each CPU ----------------------------------------------------- 1-4
1.4 Software for Product Application ---------------------------------------------------------------------- 1-5
1.4.1 Checking software ------------------------------------------------------------------------------------ 1-5
1.4.2 XG5000 -------------------------------------------------------------------------------------------------- 1-7
1.4.3 Version checking -------------------------------------------------------------------------------------- 1-7
Chapter 2 Product Specifications
2.1 General Specifications --------------------------------------------------------------------------------------- 2-1
2.2 Performance Specifications --------------------------------------------------------------------------------- 2-2
2.2.1 XGL-EFMT(B)/EFMF(B) ------------------------------------------------------------------------------------ 2-2
2.2.2 XGL-EH5T ---------------------------------------------------------------------------------------------- 2-2
2.2.3 Specification of Communication load amount ------------------------------------------------- 2-4
2.3 Structure and Characteristics ------------------------------------------------------------------------------- 2-5
2.3.1 Structure of XGL-EFMT(B)/EFMF(B)------------------------------------------------------------------- 2-5
2.3.2 Structure of XGL-EH5T module --------------------------------------------------------------- 2-8
2.4 Cable Specifications ------------------------------------------------------------------------------------------ 2-9
2.4.1 UTP cable ----------------------------------------------------------------------------------------------- 2-9
2.4.2 Optical cable ------------------------------------------------------------------------------------------- 2-11
Chapter 3 Installation and Operation
3.1 Precautions for Installation ---------------------------------------------------------------------------------- 3-1
3.1.1 Installation ----------------------------------------------------------------------------------------- 3-1
3.1.2 Operation steps--------------------------------------------------------------------------------------- 3-2

3.2 Installation of the Product ----------------------------------------------------------------------------------- 3-3
3.2.1 Installation of XGL-EFMT(B) ------------------------------------------------------------------- 3-3
3.2.2 Installation of XGL-EFMF(B) ----------------------------------------------------------------------- 3-5
3.2.3 Installation of XGL-EH5T ----------------------------------------------------------------------- 3-6
3.3 Operation -------------------------------------------------------------------------------------------------------- 3-8
3.3.1 Precautions for system configuration ----------------------------------------------------------- 3-8
3.3.2 Checklist prior to test operation ------------------------------------------------------------------ 3-8
3.3.3 How to install or remove the module ---------------------------------------------------------- 3-10
Chapter 4 System Configuration
4.1 Configuration of Network System ------------------------------------------------------------------------- 4-1
4.1.1 Ethernet network composed of LSIS’ PLCs------------------------------------------------------------ 4-1
4.1.2 Dedicated network composed of LSIS’ PLCs --------------------------------------------------------- 4-2
4.1.3 Combined with Public network and dedicated network system ----------------------------------- 4-2
4.1.4 Ethernet System of Public Network and Dedicated Network -------------------------------------- 4-3
4.1.5 Public network and dedicated network system composed of LSIS’
and other company’s PLCs -------------------------------------------------------------------------------- 4-4
4.1.6 System configuration using dedicated Ethernet between HMIs,
PLCs at XGR system ---------------------------------------------------------------------------------------- 4-5
4.1.7 System configuration using dedicated Ethernet between HMIs,
PLCs at XGR system ---------------------------------------------------------------------------------------- 4-6
Chapter 5 XG5000 Program
5.1 Introduction ----------------------------------------------------------------------------------------------------- 5-1
5.2 Basic Settings -------------------------------------------------------------------------------------------------- 5-2
5.2.1 PLC type setting ------------------------------------------------------------------------------------- 5-2
5.2.2 Register of communication module ------------------------------------------------------------- 5-3
5.2.3 Standard settings (Module) ------------------------------------------------------------- 5-8
5.3 High-speed link Settings ------------------------------------------------------------------------------------5-13
5.3.1 Setting of high-speed link parameters -------------------------------------------------------- 5-13
5.3.2 Setting of high-speed link parameters -------------------------------------------------------- 5-18
5.4 P2P Settings -------------------------------------------------------------------------------------------------- 5-19
5.4.1 P2P parameters ------------------------------------------------------------------------------------ 5-19
5.5 Connect and Download to communication Module ------------------------------------------------- 5-21
5.5.1 Download/Upload -------------------------------------------------------------------------------- 5-21
5.5.2 Enable Link ------------------------------------------------------------------------------------------ 5-24
5.6 System Diagnosis ------------------------------------------------------------------------------------------- 5-28
5.6.1 Execution of the diagnosis function ----------------------------------------------------------- 5-28
5.6.2 Type of diagnosis functions --------------------------------------------------------------------- 5-29

Chapter 6 High-speed Link Service
6.1 Introduction ----------------------------------------------------------------------------------------------------- 6-1
6.2 High-speed link Send/Receive Processing ------------------------------------------------------------- 6-2
6.3 Operation Sequence through High-speed link --------------------------------------------------------- 6-3
6.4 High-speed link parameters settings --------------------------------------------------------------------- 6-4
6.4.1 Execution of XG5000 ------------------------------------------------------------------------------- 6-4
6.4.2 Standard settings (Module) ----------------------------------------------------------------------- 6-5
6.4.3 High-speed Link parameters (HsLink) --------------------------------------------------------- 6-6
6.5 High-speed Link Information ------------------------------------------------------------------------------ 6-11
6.5.1 High-speed link flags ------------------------------------------------------------------------------ 6-11
6.5.2 Monitor of High-speed link information ------------------------------------------------------- 6-13
6.6 High Speed Link at Redundant system ------------------------------------------------------------- 6-15
6.6.1 In case of redundant network ------------------------------------------------------------------ 6-15
6.6.2 Monitor of High-speed link information ------------------------------------------------------- 6-17
6.7 High Speed Link at Redundant system ------------------------------------------------------------- 6-18
6.7.1 In case of redundant system ----------------------------------------------------------------- 6-18
6.7.2 In case of single network ------------------------------------------------------- 6-25
Chapter 7 P2P Service
7.1 Introduction ----------------------------------------------------------------------------------------------------- 7-1
7.1.1 Introduction to P2P service ----------------------------------------------------------------------- 7-1
7.1.2 Configuration of P2P parameters ---------------------------------------------------------------- 7-2
7.2 Type of P2P Service ----------------------------------------------------------------------------------------- 7-3
7.2.1 Type of P2P Instructions --------------------------------------------------------------------------- 7-3
7.2.2 Type of P2P Service ------------------------------------------------------------------------------- 7-4
7.3 How to Set P2P Service ------------------------------------------------------------------------------------- 7-5
7.3.1 Ethernet (server) driver ---------------------------------------------------------------------------- 7-5
7.3.2 P2P channel ------------------------------------------------------------------------------------------ 7-6
7.3.3 P2P block -------------------------------------------------------------------------------------------- 7-9
7.3.4 User Defined Frame ----------------------------------------------------------------------------- 7-12
7.4 P2P Service Operation ------------------------------------------------------------------------------------- 7-16
7.5 P2P Diagnosis Function ------------------------------------------------------------------------------------ 7-18
7.6 E-mail service using P2P service --------------------------------------------------------------------- 7-20
7.6.1 E-mail service ---------------------------------------------------------------------------- 7-20
7.7 P2P service at Redundant System ------------------------------------------------------------------- 7-29

Chapter 8 Dedicated Communication
8.1 Dedicated Communication ---------------------------------------------------------------------------------- 8-1
8.1.1 Introduction ------------------------------------------------------------------------------------------- 8-1
8.1.2 Frame structure ------------------------------------------------------------------------------------- 8-2
8.1.3 List of instructions ----------------------------------------------------------------------------------- 8-4
8.1.4 Data type ---------------------------------------------------------------------------------------------- 8-4
8.2 Execution of Commands ---------------------------------------------------------------------------------- 8-5
8.2.1 Read separated direct variable -------------------------------------------------------------- 8-5
8.2.2 Read continuous direct variable ------------------------------------------------------------ 8-8
8.2.3 Write separated direct variable -------------------------------------------------------------- 8-10
8.2.4 Write continuous direct variable ----------------------------------------------------------- 8-12
8.2.5 Status read request (MMI -> PLC) ---------------------------------------------------------- 8-14
8.3 Modbus/TCP Dedicated Server -------------------------------------------------------------------------- 8-19
8.3.1 Driver settings -------------------------------------------------------------------------------------- 8-19
Chapter 9 Remote Connection Service
9.1 Introduction ----------------------------------------------------------------------------------------------------- 9-1
9.2 Setting and Connection -------------------------------------------------------------------------------------- 9-2
9.2.1 Remote 1 connection (If RS-232C cable used) -------------------------------------- 9-3
9.2.2 Remote 2 connection (If RS-232C cable is used for local connection) ---------------- 9-6
9.2.3 Remote 1 connection directly from PC connected with Ethernet --------------- 9-8
9.2.4 Remote 2 connection directly from PC connected with Ethernet --------------- 9-10
Chapter 10 Troubleshooting
10.1 Check through communication module LED -------------------------------------------------------- 10-1
10.1.1 Abnormal operation display XGL-EFMT/EFMF ------------------------------------------- 10-1
10.1.2 Abnormal operation display XGL-EFMTB/EFMFB--------------------------------------- 10-2
10.1.3 Abnormal operation display XGL-EH5T ------------------------------------------- 10-4
10.2 Module Check with XG5000 ------------------------------------------------------------------------ 10-5
10.2.1 Error check in XG5000 ------------------------------------------------------------------------- 10-5
10.2.2 Error code ------------------------------------------------------------------------------------------ 10-6
10.3 Module Check through Error Codes ------------------------------------------------------------------- 10-7
10.3.1 Troubleshooting ---------------------------------------------------------------------------------- 10-7
10.4 Error code received from Comm. module ---------------------------------------------------------- 10-9
10.4.1 Error received from Comm. module --------------------------------------------------------- 10-9

Chapter 11 Compliance with EMC Specifications
11.1 Requirements Complying with EMC Specifications ----------------------------------------------- 11-1
11.1.1 EMC specifications --------------------------------------------------------------------------- 11-1
11.1.2 Panel --------------------------------------------------------------------------------------- 11-2
11.1.3 Cable -------------------------------------------------------------------------------------- 11-3
11.2 Requirements Complying with Low Voltage Direction -------------------------------------------- 11-4
11.2.1 Specifications applicable to XGT series ---------------------------------------------------- 11-4
11.2.2 Selection of XGT series PLC ------------------------------------------------------------------ 11-4
Appendix
A.1 XGT CPU Memory Device List ---------------------------------------------------------------------------- A-1
A.1.1 Device of XGK CPU ---------------------------------------------------------------------------- A-1
A.1.2 Device of XGI CPU ----------------------------------------------------------------- A-2
A.1.3 Device of XGR CPU ----------------------------------------------------------------- A-2
A.2 Terminology ---------------------------------------------------------------------------- A-3
A.3 List of Flags ---------------------------------------------------------------------------- A-8
A.3.1 List of Special Relays (F) ---------------------------------------------------------------------------- A-8
A.3.2 List of Communication Relays (L)---------------------------------------------------------------- A-16
A.4 ASCII Code Table ------------------------------------------------------------------------------------------- A-22
A.5 Comparison Table of Ethernet Technology ----------------------------------------------------------- A-25
A.6 External Dimensions --------------------------------------------------------------------------------------- A-26

Chapter 1 Overview
1-1
Chapter 1 Overview
1.1 Introduction
This user’s manual is prepared to describe Fast Ethernet Interface module of XGT series PLC
(hereinafter referred to as FEnet I/F module, 1Gbps).
Ethernet is a ‘technical standard' established by the international organization of IEEE.
Communication is controlled by CSMA/CD method and network can be established with easy. In addition,
a great amount of data can be transferred with high speed. FEnet I/F module is an interface module to
communicate data between higher level system such as host PC and PLC, or between PLCs with
electric/optical media (10BASE-T/100BASE-TX/1000BASE-T, 100BASE-FX/1000X).
[Fig. 1.1.1] Configuration diagram of FEnet system
FEnet I/F module has variety applicable communication systems. Refer to Chapter 4 System Configuration
for detailed system configuration and its description.
1) Communication between PLC and host PC (MMI)
2) Mutual exchange or monitoring data between PLCs /monitoring
3) Data management or system control for field devices.

Chapter 1 Introduction
1-2
1.2 Features of FEnet I/F Module
1.2.1 Characteristic of FEnet I/F module
XGT FEnet I/F module supports TCP/IP and UDP/IP protocols and has the features as specified below;
Fast Ethernet (FEnet I/F module):
▶Module exchange on CPU RUN with module exchange switch in the CPU is possible.
▶Module exchange on CPU RUN with module exchange wizard of XG5000 is possible.
▶Conforms to IEEE 802.3 standard (Ethernet standard supported).
▶High-speed link service supported for communication between LSIS’ PLCs with high speed.
▶XG5000, a communication parameter configuration tool, is provided.
▶High-speed link block setting available to link between modules.
(Max. Send Data: 64blocks x 200 words, Max. Receive Data: 128 blocks x 200 words, Totally
128 blocks can be setup. (Send + Receive)) .
▶In addition to High-speed link service, Communication with up to 16 Ethernet devices is
available (dedicated communication + P2P communication).
▶Loader service (XG5000 connection) is supported through Ethernet: (dedicated TCP/IP PORT:
2002 allotted).
▶It is easy to connect with other company’s Ethernet device through P2P communication and
XG5000. (Variable READ/WRITE service is available (through Dynamic Connection))
▶10BASE-T/100BASE-TX/1000BASE-T, 100BASE-FX/1000X media supported.
▶Data is accessible via the public network.
▶LS protocol (XGT) and other company’s protocol (MODBUS TCP) supported
(dedicated service)
▶Convenient client function supported for communication between LSIS’ PLCs and for
communication with other company’s Ethernet device.
(XGT, Modbus TCP P2P client function)
▶Dynamic IP supported to make ADSL network available
▶Access table provided for host PC (MMI) and communication security.
▶Dynamic Connection/Disconnection supported through P2P service.
▶Various diagnosis functions and status information of modules and network provided.
1) CPU module status
2) Communication module status
3) Communication service (High-speed link, dedicated service, P2P) status
4) Autoscan function used to visualize the information of LSIS’ communication
modules connected within the network
5) PING test function provided to check if other modules exist.
6) Type and average amount of packet received by communication module provided
(network load predictable)
7) Diagnosis function provided for communication module through the network.
▶E-MAIL service (ASCII) provided.
▶Up to 24 Ethernet communication modules can be installed on main and extension base.
(For XGR, FEnet module can be installed on only main base)
▶One IP Solution function provided (XGR O/S Version 2.4 or above)

Chapter 1 Overview
1-3
1.2.2 Characteristic of XGL-EH5T (switch)
Switch module is HUB module having the switching function for interface with system based on Ethernet or
XGT FEnet module. It improves the weak points of the external hub module (using external power source and
low reliability) and it can be installed on XGT base to simplify the work and reduce the fault factor.
(1) Available to install at XGT base
It doesn’t need a external power source and can be installed at XGT base. Compact size for easy installation
(2) Reliability applying to industrial standard
It passed the noise, environment test based our company standard comparing other switches
(3) Built-in Auto Cross Over function (For convenience of wiring)
(4) High speed link function is guaranteed
It canceled Broadcast storm function for normal operation of High speed link packet
(5) CHS GROUND supported at RJ-45 connector
In case of using shielded cable (FTP/STP), effective for reducing the transmission error rate

Chapter 1 Introduction
1-4
1.3 Product Configuration
1.3.1 Designation
Product configuration of XGT FEnet I/F module is as follows;
Designations Description Remarks
XGK/XGI/XGR
XGL-EFMT 10BASE-T/100BASE-TX Category 5 or more(STP)
XGL-EFMTB 100BASE-TX/1000BASE-T Category 5 or more(STP)
XGL-EFMF
100BASE-FX
Fiber Optic (SC)
XGL-EFMFB
100BASE-FX/1000X
Fiber Optic(LC/SFP)
XGL-EH5T 10/100BASE-TX Switch
Notes
1) AUI (10BASE-5) is not supported in XGT series.
2) In the case that UTP cable is used, use the switching hub of 100Mbps
, which can be used
together with the 10Mbps Ethernet device (category 3 or less) but its baud rate will be limited to
10Mbps.
Pay attention to installation of the system.
3) XGL-EH5T can be installed on XGT base and used as switch without specific program. It has
maximum 100Mbps speed
1.3.2 Available units to be installed on each CPU
The maximum installation number of modules based on CPU type of each FEnet I/F module is
described in the table below. After due consideration of the number of communication modules
available, apply such applicable modules to the system configuration.
Segment
XGK
XGI
XGR
CPUH
CPUU CPUA
CPUS
CPUE CPUSN
CPUHN
CPUUN
CPUU
CPUH
CPUS CPUE CPUU/
D
CPUU
N
CPUH
/T
CPUH
/F
CPUH
/S
Number of HS
Link use
module(Maximu
m)
12 units 6 units
Number of P2P
use
modules(maximu
m)
8 units 6 units
Maximum
number of
modules(server
use modules
included)
24 units 6 units

Chapter 1 Overview
1-5
1.4 Software for Product Application
The following is for main programming tools and other producing software needed to use FEnet I/F
module. For more precise application of program and communication, please refer to the details below
so to apply to the system.
1.4.1 Checking software
(1) Application to XGT series
Classification
Programming tool and Frame Setting
XGL-EFMT(B)
10BASE-T/100BASE-
TX/1000BASE-T
XG5000
XGL-EFMF(B) 100BASE-FX/1000X
XGL-EH5T Switch No relation
(2) CPU version to use FEnet I/F module
Section Section
Available version
(recommended)
Reference
XGK series
XGK-CPUH V4.55
XGK-CPUS
V4.55
XGK-CPUA
V4.55
XGK-CPUE
V4.55
XGK-CPUU
V4.55
XGK-CPUSN
V1.05
XGK-CPUHN
V1.05
XGK-CPUUN
V1.05
XGI series
XGI-CPUU/D
V4.06
XGI-CPUU
V4.06
XGI-CPUH
V4.06
XGI-CPUS
V4.06
XGI-CPUE
V4.06
XGI-CPUUN
V1.12
XGR series
XGR-CPUH/T
V2.72
XGR-XPUH/F
V2.72
Software
XG5000
V4.10

Chapter 1 Introduction
1-6
Notes
1) The software above can be downloaded presently from the web site for its application. If the
Internet is not available, please visit the nearest agent of service center to get the applicable
installation CD-ROM to use.
Internet web site : http://www.lsis.com
2) RS-232C and USB port of CPU module is available for downloading the program made by XG5000
and communication configuration made by XG5000.
Refer to CPU or XG5000 manual for connection diagram of each cable.
3) At the lower version than above table, some function may not work properly. Check the version
before using