LSIS XEC-DN32H/DC User manual

Programmable Logic Control
XGB Hardware(
IEC)
XEC-DN32
H
XEC-DN64
H
XEC-DP32
H
XEC-DP
64H
XEC-
DR32H
XEC-
DR64H
XEC-DN32H
/DC
XEC-DR32H
/D1
XEC-DR64H
/D1
XGT Series

Safety Instruction
1
Before using the product …
For your safety and effective operation, please read the safety instructions thoroughly before
using the product.
►Safety Instructions should always be observed in order to prevent accident or risk with the
safe and proper use the product.
►Instructions are separated into “Warning” and “Caution”, and the meaning of the terms is as
follows;
This symbol indicates the possibility of serious injury or death if
some applicable instruction is violated
This symbol indicates the possibility of slight injury or damage to
products if some applicable instruction is violated
►The marks displayed on the product and in the user’s manual have the
following meanings.
Be careful! Danger may be expected.
Be careful! Electric shock may occur.
►The user’s manual even after read shall be kept available and accessible to
any user of the product.
Warning
Caution

Safety Instruction
2
Safety Instructions when designing
Please, install protection circuit on the exterior of PLC to protect
the whole control system from any error in external power or PLC
module. Any abnormal output or operation may cause serious problem
in safety of the whole system.
- Install applicable protection unit on the exterior of PLC to protect
the system from physical
damage such as emergent stop switch,
protection circuit, the upper/lowest limit switch, forward/reverse
operation interlock circuit, etc.
- If any system error (watch-dog timer error, module installation error,
etc.) is detected during CPU operation in PLC, the whole output is
designed to be turned off and stopped for system safety. However,
in case CPU error if caused on output device itself such as relay or
TR can not be
detected, the output may be kept on, which may
cause serious problems. Thus, you are recommended to install an
addition circuit to monitor the output status.
Never connect the overload than rated to the output module nor
allow the output circuit to have a short circuit, which may cause a
fire.
Never let the external power of the output circuit be designed to
be On earlier than PLC power, which may cause abnormal output or
operation.
In case of
data exchange between computer or other external
equipment and PLC through communication or any operation of
PLC (e.g. operation mode change), please install interlock in the
sequence program to protect the system from any error. If not, it
may cause abnormal output or operation.
Warning

Safety Instruction
3
Safety Instructions when designing
Safety Instructions when designing
I/O signal or communication line shall be wired at least 100mm
away from a high-voltage cable or power line.If not, it may cause
abnormal output or operation.
Caution
Use PLC only in the environment specified in PLC manual or
general standard of data sheet. If not, electric shock, fire, abnormal
operation of the product or flames may be caused.
Before installing the module, be sure PLC power is off. If not,
electric shock or damage on the product may be caused.
Be sure that each module of PLC is correctly secured. If the
product is installed loosely or incorrectly, abnormal operation, error or
dropping may be caused.
Be sure that I/O or extension connecter is correctly secured. If
not, electric shock, fire or abnormal operation may be caused.
If lots of vibration is expected in the installation environment,
don’t let PLC directly vibrated. Electric shock, fire or abnormal
operation may be caused.
Don’t let any metallic foreign materials inside the product, which
may cause electric shock, fire or abnormal operation..
Caution

Safety Instruction
4
Safety Instructions when wiring
Prior to wiring, be sure that power of PLC and external power is
turned off. If not, electric shock or
damage on the product may be
caused.
Before PLC system is pow
ered on, be sure that all the covers of
the terminal are securely closed. If not, electric shock may be caused
Warning

Let the wiring installed correctly after checking the voltage rated
of each product and the arrangement of terminals. If not, fire,
electric shock or abnormal operation may be caused.
Secure the screws of terminals tightly with specified torque when
wiring. If the screws of terminals get loose, short circuit, fire or abnormal
operation may be caused.
*
Surely use the ground wire of Class 3 for FG terminals, which is
exclusively used for PLC. If the terminals
not grounded correctly,
abnormal operation may be caused.
Don’t let any foreign materials such as wiring waste inside the
module while wiring, which may cause fire, damage on the product
or abnormal operation.
Caution

Safety Instruction
5
Safety Instructions for test-operation or repair
Safety Instructions for waste disposal
Don’t touch the terminal when powered. Electric shock or abnormal
operation may occur.
Prior to cleaning or tightening the terminal screws, let all the
external power off including PLC power. If not, electric shock or
abnormal operation may occur.
Don’t let the battery recharged, disassembled, heated, short or
soldered. Heat, explosion or ignition may cause injuries or fire.
Warning
Don’t remove PCB from the module case nor remodel the module.
Fire,electric shock or abnormal operation may occur.
Prior to installing or disassembling the module, let all the external
power off including PLC power. If not, electric shock or abnormal
operation may occur.
Keep any wireless installations or cell phone at least 30cm away
from PLC. If not, abnormal operation may be caused.
Caution

Product or battery waste shall be processed as industrial waste.
The waste may discharge toxic materials or explode itself.
Caution

Safety Instruction
6

Revision History
1
Revision History
Version Date Remark Chapter
V 1.0 2009.2 1. First Edition -
V 1.1 2009.6
1. Add detailed description on High Speed Counter
specification
Ch8.1.1
V 1.2 2009.10 1. Add DC power unit
Ch2.1, Ch2.2
Ch4.1, Ch4.3
Ch7.2.1, Ch7.2.2
Ch8.1.1, Ch8.1.2
Appendix2
V1.5 2010.10
1. Add new module
2. Error in consumption current calculation fixed
3. Error in Momentary power failure and watch dog
fixed
4. Error in program execution fixed
5. Error in memory unit fixed
6. Error in remote function fixed
7. RTC flag, setting method modified
8. Input speciation of main unit fixed
9. Contents related with XGI deleted
10. Voltage reference fixed
11. Contents related with STOP LED deleted
12. APM_SSSB modified
13. XEC-DP32H/DP64H added
Ch2.1, Ch2.2,
Ch2.3.1, Ch4.1
Ch4.3, Ch4.4
Ch5.1.2, Ch5.1.4
Ch5.2.2
Ch5.4.1
Ch6.4
Ch6.12
Ch7.2.1, Ch7.2.2
Ch10.2
Ch10.3
Ch.11
Appendix4
Ch4.1, Ch4.3
Ch7.3.4, Ch7.3.6
Appendix2
V1.6 2014.2
1. Domain Of Homepage Changed
2. Add XEC-DN32H/DC
Front/Back
Cover
Ch2.1, Ch2.2
Ch4.1, Ch4.3
Ch7.2.1, Ch7.3.3
Ch8.1.1
Appendix2
V1.7 2015.7
1. Address & phone number changed
2. Add new module
3. Vibration Specification modified
Back Cover
Ch2.1, Ch2.2,
Ch2.3.3, Ch2.3.4
Ch3.1
V1.8 2016.11
1. . Add new module
- XBE-DN32A Ch7
V 1.9 2020.06 LSIS to change its corporate name to
LS ELECTRIC
Entire

Revision History
2

About User's Manual
１
About User’s Manual
Thank you for purchasing PLC of LS ELECTRIC Co.,Ltd.
Before use, make sure to carefully read and understand the User’s Manual about the functions, performances,
installation and programming of the product you purchased in order for correct use and importantly, let the end user
and maintenance administrator to be provided with the User’s Manual.
The Use’s Manual describes the product. If necessary, you may refer to the following description and order
accordingly. In addition, you may connect our website(http://www.lselectric.co.kr/)and download the information as
a PDF file.
Relevant User’s Manual
Title Description No. of User
Manual
XG5000 User’s
Manual
(XGI/XGR/XEC)
It describes how to use XG5000 software especially about
online functions such as programming, printing, monitoring
and debugging by using XGB (IEC language)
10310000512
XGI/XGR/XEC Series
Instruction &
Programming
It describes how to use the instructions for programming
using XGB (IEC language) series.
10310000510
XGB Hardware
User’s Manual (IEC
language)
It describes how to use the specification of power/input
/output/expansion modules, system configuration and built-in
High-speed counter for XGB main unit.
10310000983
XGB Analog
User’s Manual
It describes how to use the specification of analog
input/analog output/temperature input module, system
configuration and built-in PID control for XGB main unit.
10310000920
XGB Position
User’s Manual
It describes how to use built-in positioning function for XGB
main unit.
10310000927
XGB Cnet I/F
User’s Manual
It describes how to use built-in communication function for
XGB main unit and external Cnet I/F module.
10310000816
XGB Fast Ethernet I/F
User’s Manual
It describes how to use XGB FEnet I/F module. 10310000873