M-system 6AC User manual

6AC

P. 1 / 2 EM-4236 Rev.4

INSTRUCTION MANUAL

MODEL 6AC

AC TRANSMITTER

COMPONENT IDENTIFICATION

INSTALLATION

■

35-mm DIN RAIL MOUNTING PLATE A-31 (optional) mm (inch)

1) AttachtheunittotheDINrailmountingplatewithscrews

included in the package.

2) Set the plate so that its DIN rail adapter is at the bottom.

Hang the upper hook at the rear side on the DIN rail and

push in the lower. When removing the plate, push down

the DIN rail adapter utilizing screwdriver (–) and pull.

■ SPRING CLIP A-02 (optional)

1) Remove the two flat-head

screws Alocated at the bot-

tom as shown to the right.

2) Set Spring Clip Bon the

mounting hole and

tighten it as shown to

the right with a binding

screw Cincluded in the

package.

3) Check that the clips con-

tract and release

smoothly.

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

package you received as below.

If you have any problems or questions with the product,

please contact M-System's Sales Office or representatives.

■ PACKAGE INCLUDES:

Signal conditioner ....................................................... (1)

(Option) DIN rail mounting plate (model: A-31) . (1 set)

(Option) Spring clip (model: A-02) ....................... (1 set)

■ MODEL NO.

Check that model No. described on specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, installation, connection and basic mainte-

nance procedures.

POINTS OF CAUTION

■ GENERAL

• Before you remove the unit from its base socket or mount it,

turn off the power supply and input signal for safety.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing and ventilate it.

• Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

• Environmental temperature must be within -5 to +70°C (23

to158°F)withrelativehumiditywithin30to90%RHin order

to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

80 (3.15) MIN.

Specification Label

Knurled Knob

Body

Knurled Knob

Connection Diagram Label

(Top)

6AC

P. 2 / 2 EM-4236 Rev.4

EXTERNAL DIMENSIONS mm (inch)

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the

connection diagram label on top of the unit.

CHECKING

1) Terminal wiring: Check that all cables are correctly

connected according to the connection diagram.

2) Input: Check that the input signal is within 0 – 100% of

the full-scale.

3) Output: Check that the load is within the permissible

limit including wiring resistance.

Supply Voltage (V) –␣ 13 (V)

Load Resistance (Ω) = 0.02 (A)

(including leadwire resistance)

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

specifications, therefore you usually do not need any calibra-

tion.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following. Zero and Span adjustments are located behind the

top cover. Release the knurled knobs and open the cover.

■ HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufficient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0% with the

VR1.

2) SPAN: Apply 100% input and adjust output to 100% with

the VR2.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above procedure

1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■ CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the "ADJUST-

MENT PROCEDURE" explained earlier.

–

LOAD

OUTPUT

24VDC

4 – 20mADC

INPUT

1234

VR1 VR2

76 (2.99) dia. 40 (1.57)

52.5 (2.07)

1 (.04)

60.9 (2.40)

46 (1.81)

50 (1.97)

4–M3 (.12) TAP

6 (.24) deep

1 2 3 4

5 6

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.