Maytronics ACTIVE 6 User manual

8180002
User Instructions
EN
Maytronics Dolphin robotic pool cleaner
M600 / ZENIT 60 / ACTIVE 6 / ACTIVE X6 / ACTIVE ULTIMATE

1
M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
M600 / ZENIT 60 / ACTIVE 6 / ACTIVE X6 /
ACTIVE ULTIMATE Robotic Pool Cleaner
User Instructions
EN
Contents
1. INTRODUCTION ......................................................................................................................................................2
2. SPECIFICATIONS .....................................................................................................................................................2
3. WARNINGS AND CAUTIONS ..............................................................................................................................2
3.1 Water conditions ...........................................................................................................................................3
4. ROBOTIC POOL CLEANER PARTS ................................................................................................................... 4
5. USING THE ROBOTIC POOL CLEANER ............................................................................................................5
5.1 Setup ..................................................................................................................................................................5
5.2 Placing the Robotic Pool Cleaner into the pool............................................................................. 6
5.3 Plug in the power supply ........................................................................................................................ 6
5.4 Operating the Robotic Pool Cleaner without using your smart device ...............................7
5.5 Using the power supply............................................................................................................................7
5.6 Robotic Pool Cleaner indicator lights ..................................................................................................7
5.7
Removing the Robotic Pool Cleaner from the pool ...................................................................... 8
6. CARE AND MAINTENANCE................................................................................................................................ 9
6.1
Cleaning after use - Removing and cleaning the dual filter baske t............................................9
6.2
Periodic filter cleaning .............................................................................................................................10
6.3
Cleaning the impeller .................................................................................................................................11
6.4
Periodic general maintenance - Recommended at least once a week .................................. 12
7. OFFSEASON STORAGE...................................................................................................................................... 12
8. USE THE
MyDolphin™ Plus IOT MOBILE APP............................................................................................13
8.1
Getting Started with the MyDolphin™ Plus App ..............................................................................13
8.2
Prepare the Pool Cleaner for Connection ......................................................................................... 13
8.3
Activate the Pool Cleaner Using your Mobile Smart Device ...................................................... 13
8.4
Led Lights .......................................................................................................................................................14
9. TROUBLESHOOTING ........................................................................................................................................... 15
10.
MyDolphin™ Plus - TROUBLESHOOTING .................................................................................................... 17

2M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
1. INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner.
We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient, and
cost-effective pool cleaning, to enhance your pool’s hygiene.
Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologies, exceptional ease of use,
long-lasting performance, and simple maintenance. You and your family will be free to enjoy your
swim with full confidence that your pool is completely clean.
2. SPECIFICATIONS
This product is in accordance with EU Regulation & Directive 2014/531EU.
For full information, please contact us at www.maytronics.com/contact-us-en and ask for the EC
declaration of conformity.
3. WARNINGS AND CAUTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
Please adhere strictly to the following WARNINGS:
Take the Robot Pool Cleaner out of the pool before allowing people to enter the pool.
When examining the Robot Pool Cleaner, disconnect the main power supply.
Ensure that children do not attempt to access Robot Pool Cleaner while it is operating.
Keep the Robot Pool Cleaner out of the reach of children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction.
Only an original power cable must be used, at all times. Replaced by a Robot Pool Cleaner
certified technician, in case of need to avoid hazard.
Digital switch-mode power supply
IP 54
Input: 100-250 AC Volts, 50-60Hertz, 180 Watt
Output: <30VDC
Bluetooth®/Wifi® Max tras power 10mW EIRR, 2.4 GHz frequency
WARNING
WARNING
WARNING
WARNING
WARNING
Robot
Motor protection: IP 68
Minimum depth: 0.4m / 1.33ft
Maximum depth: 5m / 16.4ft

3
M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
The unit must be connected only to a supply circuit that is protected by a ground-fault circuit
interrupter (GFCI). This GFCI should be tested on a routine basis. To test the GFCI, push the test
button. The GFCI should interrupt power. Push the reset button. Power should be restored. If
the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the
power unit without the test button being pushed, a ground current may be flowing, indicating
the possibility of an electric shock. Do not use the power unit. Disconnect the power unit and
contact the manufacturer for assistance.
To reduce the risk of electric shock replace damaged cord immedietely.
Do not use extension cord to connect unit to electric supply; provide a properly located outlet.
Please ensure that the following PRECAUTIONS are implemented:
Operator should keep hands away from driving belt mechanism.
Position the Caddy and power supply at least 3.5m/12ft from pool’s edge – during operation.
For continued protection against possible electric shock, the power supply unit should be placed
at least 11cm/4in above ground.
When lifting the Robot Pool Cleaner, take care to prevent back injury.
Do not bury cord – locate cord to minimize abuse from lawn mowers, hedge trimmers and other
equipment.
Do not use the pool cleaner if you have added liquid flocculant or any other clarifier to the pool
water. These substances obstruct and damage the robot's filters.
3.1 Water Conditions
Use the Robotic Pool Cleaner in the following water conditions:
Chlorine Max 4 PPM
pH 7.0-7.8 PPM
Temperature 6-35°C / 43-95°F (below 15°C / 59°F climbing performance may be affected)
NaCl Maximum = 5000 PPM
WARNING
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
WARNING

4M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
4. ROBOTIC POOL CLEANER PARTS
Robotic Pool Cleaner
Filtration
Power supply
Caddy kit
Start the season with the net filters for large debris then use ultra-fine filters for daily use.
* The net filters are assembled in the filter basket.

5
M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
5. USING THE ROBOTIC POOL CLEANER
5.1 Setup
Before using the Robotic Pool Cleaner for the first time, perform the following steps:
Position the power supply
at approximately the middle of the
long side of the pool, at least at a
distance of 3.5m /12ft.
Unwind the cable and stretch it out completely so that it
has no kinks.
Attach the floating cable to the power supply:
Insert the cable with the notch on the connector (1),
lined up with the groove in the socket on the power
supply, and turn clockwise (2).
11cm/4 in
minimum
11cm/4 in
minimum
5.1.25.1.1
5.1.3
1
2

6M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
5.2 Placing the Robotic Pool Cleaner into the pool
Place the Robotic Pool Cleaner in the pool.
Release it and let it sink to the floor of the pool.
Make sure that the floating cable is free of any obstacles.
5.2.1
Connect the power supply to the AC.
11cm/4 in
minimum
11cm/4 in
minimum
5.3 Plug in the power supply
5.3.1

7
M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
5.4 Operating the Robotic Pool Cleaner without using your smart device
Press the power button to turn the robot ON.
The Robotic Pool Cleaner will now operate until it has reached the end of the cleaning cycle.
5.5 Using the power supply
Your power supply is designed to provide you with the most advanced
features to improve your experience.
• A single on/off button for an easy operation.
• LED indicators for the advanced features.
LED indications table:
5.6 Robotic Pool Cleaner indicator lights
Light Indication
Blue blinking Normal operation of the Robotic Pool Cleaner
Green blinking
Remote-Control or Smartphone communicate
with the Robotic Pool Cleaner
Red constant
Robot error. Check the Troubleshooting section
for solutions.
If none of the solutions solve the issue,
contact your dealer to check the Robotic Pool
Cleaner.
5.6.1
Indicator lights
Indicator lights.
Lights display Meaning
Blue circle Blinks 4 times Occur after connecting the power-supply to the
power outlet.
Blue connectivity light is consistent Bluetooth® connected
Green and Blue connectivity lights
blink alternately
Pairing process is ongoing
Green connectivity light is on Wi-Fi® connected to home network

8M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
Place the Robotic Pool Cleaner on the side of the pool
and let the water drain out.
Option A
The easiest and most fun way to get the robot out of the water:
1. Log into the MyDolphin™ Plus app and click "Pick-up mode".
2. The robot will reach the wall closest to it and will rise above the water surface.
3. Grab the robot by the handle and pull it out the water.
Option B
Use the floating cable to pull the Robotic Pool Cleaner to the side of the pool.
Use the handle to remove the robot from the pool.
WARNING
Please use the cable to pull the robot to the surface, then use the handle.
5.7.3
5.7.2
Turn OFF the power supply.
5.7.1
5.7 Removing the Robotic Pool Cleaner from the pool
WARNING

9
M600 / ZENIT 60 / ACTIVE X6 / ACTIVE ULTIMATE Robotic Pool Cleaner |User Instructions
Upon opening the filter cover,
the handle will lift independently.
Open the filter cover.
Clean the filter basket with a
hose.
Open the latch to
release the bottom lid.
Lift the basket.
Make sure the power supply is switched o.
We highly recommend cleaning the filter basket after each cleaning cycle.
Note: Do not let the filter panels dry out before cleaning.
6.1 Cleaning after use - Removing and cleaning the dual filter basket
click!
6.1.1 6.1.2
1
2
6.1.3 6.1.4 6.1.5
6. CARE AND MAINTENANCE
WARNING