METHVEN Waipori 01-8260 User manual

Methven Australia Pty Ltd
ABN 15 104 813 390
Melbourne, Australia
www.methven.com
WMKA21005
IMPORTANT
Please read all of the instructions before installation
MA018260
Waipori Bidet Mixer
01-8260
Use of this product is recommended for domestic and commercial applications.
Domestic and commercial warranty terms and conditions vary. Please refer to the Methven website
for full warranty terms and conditions - www.methven.com
All pipework must be thoroughly flushed prior to the installation of the mixer.
Inline filter washers must be installed on both hot and cold supplies to prevent foreign particles
damaging the ceramic head works.
Do not remove the ceramic head works from the mixer when installing.
Damage caused by hydrostatic testing is not covered by Methven’s warranty.
Methven recommends a licensed plumber carry out all installations in compliance with
the requirements of AS/NZS 3500. This product complies with AS/NZS 3718 regulations.
April 2012
Installation Guide
Installation
Tip: Install product on bench before
connecting second hose to mixer.
1. Cut a single 35mm diameter hole into
the mounting surface. The mounting
surface can be a maximum of 40mm
thick.
2. Insert o-ring (3) into the groove in the
bottom of the base ring (2) and fit the
base ring to the bottom of the mixer
body (1).
3. Feed the mixer’s (1) threaded
fastening tube through the hole cut in
the mounting surface.
4. Position the mixer (1) as desired and
fit the rubber washer over
the threaded fastening tube. Tighten
in place using the tube spanner (9)
(from under the mounting surface).
5. Insert the flexible hoses (7) through
the hole in the mounting surface (from
the underside) and screw them into
the base of the mixer body (1).
6. Connect the flexible hoses to the hot
and cold supplies (hot on the left,
cold on the right).
Note: It is a condition of Methven’s
warranty that the inline filter washers
supplied are fitted during this
connection.
7. Fit “pop-up” waste outlet (B) into
Bidet bowl.
8. Remove side nut (C) and insert rod with ball (D). Fit washer supplied and replace side nut
(C).
9. Join extension rod (E) to “pop-up” lever (A) under bowl.
10. Using “universal joint” provided (F) join and adjust rods to maintain “pop-up” action.
11. Connect the hoses to their respective water supplies (see over page). Two rubber washers
are provided for the flexible hose supplies connections. Machined nipple ends are required
to ensure a seal to the flexible hose nuts and the rubber washers.
12. Flush pipework thoroughly.
www.methven.com
Customer Care Hotline: 1300 METHVEN (638 483)
Email: [email protected].com
Max 40mm ø35mm Min
ø38mm Max
Cold
Hot

R35mm Min
20mm
DO NOT CRUSH
HOSE OR SWAGED ENDS
CORRECT
INCORRECT
DO NOT STRETCH OR TWIST HOSES
3
6
2
5
1
9
4
7
8
Mixer body
Tube spanner
Stream shaper
Base ring
O-ring
Threaded
fastening tube
Rubber washer
Mounting nut
Flexible inlet hoses:
cold
hot
Pop up waste
Product Components
Please check every component in accordance
with the table below
No. Item description Qty supplied
1 Tap body 1
2 Base ring 1
3 O-ring 1
4 Threaded fastening nut 1
5 Rubber washer 1
6 Mounting nut 1
7 Flexible inlet hoses 2
8 Pop-up waste 1
9 Tube spanner 1
Pop Up Waste Parts
Please check every component in accordance
with the table below
A Pop up lever 1
B Pop up waste outlet 1
C Nut 1
D Rod with ball 1
E Extension rod 1
F Universal joint 1
THE METHVEN GUARANTEE
The warranty statement shall apply to all tapware & showers supplied by Methven
For more information visit www.methven.com
THIS WARRANTY ISSUED BY: Methven Australia Pty Ltd, Melbourne Australia
Technical Specification
Inlet Connections: All 1/2" BSP
Operating Pressure: 150kPa - 500kPa
For optimum performance hot and cold water pressures should be equal.
AS/NZS 3500 stipulates a 500kPa maximum operating pressure at any outlet
within a building. Where normal pressure exceeds 500kPa, a pressure limiting
valve must be installed.
Operating Temperature: Recommended hot water supply 50°C, maximum 70°C. AS/NZS 3500 requires all
hot water supplies to any sanitary fitting to be tempered to 50°C.
Ceramic cartridges: Warranty claims will be void where the ceramic cartridge has malfunctioned due
to the presence of the following within the water supply:
Copper tube pieces
Plastic pieces
Sand, dirt or stones
Thread tape
Other objects not normally present in the potable water supplies
Hose Requirement for Mixers
Do not hydrostatic test* the installation with this mixer installed. Damage to the ceramic cartridge may
occur, voiding warranty.
*Hydrostatic testing refers to placing the system under pressure, above the recommended operating pressure, to determine water
tightness and to uncover leaks or weak joints within the system.
Care and Cleaning
Never use abrasives to clean this product. Clean regularly with contamination free warm soapy water
and a damp soft cloth. Damage caused by using unsuitable cleaning agents is not covered by warranty.
www.methven.com
Customer Care Hotline: 1300 METHVEN (638 483)
Email: [email protected].com
FA EB CD