MJ LED LIGHTNING MJ-3343A20W36DCW User manual

MINI LED PROFILE WITH DMX
MJ-3343A20W36DCW
User Manual
======PROFESSIONAL LED LIGHTING ========
Thank you for choosing our mini LED profile light. For the sake of your safety,
Please read a
nd follow these instructions carefully and keep this manual in a safe
place for future reference.

APPENDIX
DISCLAIMER
1. The device is with one year warranty . The warranty period appear non-artificial
quality problem, this company is responsible for free maintenance
2. User violate operation caused the machine failure, this is user responsibility.
3.
If due to the wrong operation or intense impact caused product destroy even
safety accidents, the manufacturer does not undertake any responsibility
4. Prohibit repl
aced product components by any person, therefore caused any
consequences will be whose responsible
Please contact us freely when you need our related products or in
formations...
9

SAFETY WARNING
1. Warning
﹡Every person involved with the installation , operation and maintenance of this
device has to be qualified .
﹡User must follow the instructions of this manual
﹡Unqualified person can not open the housing cover and operate the device , or the
dealer will not accept liability for any resulting defects or problems.
﹡The device against rain and moisture
2. Waring notes :
﹡Power supply : AC 100V-240V , 50/60Hz
﹡Make sure the power switch is off , the power plug , outlet and the earth connection
is in well condition before connecting the device with the mains.
﹡Please use qualified power plug and the outlet. Never connect the power cord of
this device with other electrical equipment.
﹡During move and installation , make sure the device not crashed with metal parts
and other tough materials.
﹡Always disconnect from the mains, when the device is on the installation and
dismantled
﹡The minimum distance between light-output and the illuminated surface must be
more than 50cm
﹡The device must only be installed on a non-flammable surface . In order to
safeguard sufficient ventilation , leave 50cm of free space around the device . Please
note that heat-sensitive objects may be deformed or damaged by the emitted heat .
﹡During the operation the housing becomes very hot ! Do not operate the device for
15 minutes after switching off .
﹡The maximum ambient temperature Ta = 45℃must never be exceeded , The
maximum housing temperature Tb = 80℃must never be exceeded .
﹡For indoor use
﹡Replace any visible cracked protective shield , filters and lens .
﹡The protective shiel, filters and lens will require weekly cleaning as smoke “Cfluid
tends to building up residues , reducing the light “Coutput very quickly.
8
OVERVIEW
Thank you for using our product, this unit is designed for indoor using, it’s widely
used for commercials, museums, restaurant, churches, educational theatres, etc. as
high power led effects lighting, this unit can be operated as a single unit or multiple
units for large applications. Due to the small size, we make a new lighting system of
wireless control by the controller instead of the DMX signal. It is available in four field
angles: 19°, 26°, 36° and 50°.
Technical Parameter:
• Power Supply: AC100V-240V, 50/60Hz
• Power Consumption: Max. 26W
• LED: 20W Cool white or Warm white
• IC Chip: Nichia
• LED Lamp: Japan Citizen
• Color Rendering Index(CRI): Ra≥90
• LED Life time: Over 50,000 hours
• Fixed Lens: 36°(19°/26°/50°optional)
• Dimmer: 0~100% linearly adjustable
• Strobe: 1-25times/sec
• Focus: Can be adjusted by hand
• Light body: Die-casting Aluminum
• Body color: Black / White
• Control Mode: DMX512 / Sound mode
• DMX Channels: 1/ 3CH (single color)
• Small volume, lightweight
• High quality optical system
• IP Rating: IP20
• Warranty : One year
• N.W.:1.6 kg
• G.W.:2.2kgs
• Dimensions :345x160x145mm
1

1. Product Introduction
1.1. Current regulation
The current need to be adjusted by software before Ex-work. (Please
check the menu description of “current adjust”.)
1.2. Screen protection
Without operate key in 30 seconds , it enter black screen (can be set)
Press any keys then it can quit screen protection status
1.3. Reminder from Signal
In the Slave State, the screen will flicker if no receive the signal from
controller or master light. Attention: When the screen flicker (it means the
cable connect is wrong), it won’t be the screen protection mode even it is
time to enter screen protection mode. If it already the screen mode, it will
automatically log out. The reason that no screen protection in flicker is to
help to user judge if there has cable connection problem or not.
1.4. Delay of controller
When push up or pull down the pushrod of the controller, the light will not
turn bright or dark at once, but change smoothly. (1 second) This function
can be turn on or turn off.
Special situation: pull down to “0”, the light will turn off right away without
delay.
1.5. Multi-light working in the same time
When using controller to control several lights, and using strobe, the
controller just send the channel data. The strobe would be showed by
itself. And should be attention for the follow situation:
2
LED show
English
Word/function
key operation
Description
LED waiting time UP/DOWN choose the
waiting time
0 = no screen protect
Screen protect time
High Power
UP/DOWN choose high
power or not
On = 100%
off = 33.3%
Power choose
dMX-controller
delay
UP/DOWN choose use
the controller delay or not
controller delay
Synchronization
UP/DOWN choose
usemulti-light
synchronization or not
Multi-light
synchronization
LoAd Long press ENTER until it
shows “LdEd”(loaded)
reset
rEturn Press ENTER to save the
data and back to main
menu.
Back to function
menu
2.3. Contor Channel
3CH model(A001)
Channel
Data
Function
CH1 0~255 Dimmer
CH2 0~5 No function
6~255 Strobe: 6 is slowest, 255 is fastest
CH3
0~25 Turn on “delay by controller”
26~200 Turn off “delay by controller”
251~255 Sound mode: the changing of the light depends on
the MIC of each light
1CH model(d001)
Channel
Data
Function
CH1
0~255
Dimmer
7

P
1、For reduce the risk of burning lamp. before the completion of step 3,
please do not connect the light to the console.
2、First of all through the "keyboard current adjustment" to adjust the ideal
current value in a light and record it.
3、Set the channels 1, 2, and 3 of the console to recorded the current values
(to represent red, green, and blue, for example,then set the channel 2
value to 100 for a green current value of 100). This step must be
completed before starting step 4! Otherwise it may be caused by
channel value is too large led lamp burning!
4、After confirming that step 3 is no problem,then connect the light to the
console. Press and hold the MENU key and ENTER key at the same time
in any main menu. After about 3 seconds, enter "DMX current adjustment"
mode. The screen will display "CSdA"(Color Scale dMX Adjustment),and
which will flicker if the DMX signal is not received
5、Wait for about 1 second, if "CSdA" is not flicker then it has correctly
received the current value passed by the console (also can through lamp
brightness to be observed), the adjustment is successful.
Press "ENTER" key to save and automatically return to "A001" menu
6、In step 5, the channel value of the console can also be changed to adjust
again. Since it is the ideal value that has already been adjusted, generally
do not need to adjust again. If you want to adjust, you must be
conscious, careful! If the current is too large, will lead to lamp
burned!
3. Set Menu
In the “dEMo” menu, long press “ENTER” to set the menu.
Press MENU to change the menu option.
6
1.
There will be many situation make the light become not
synchronization in the beginning. (For example: the different time of
opening the light will make them connect the controller in different time) .
And you can change the controller table puller data( from 20 to 0, and
back to 20), then it can be synchronization.
2. Using the controller to make program make the strobe effect to be
synchronization,the screen will be shake to judge whether it become
synchronization or not. The shake will not have any effect for the
function.
3. We have tested for several times, and it still get synchronization
in the end. But there are a lot of factor to effect the synchronization,
some software can not be controlled, such as hardware factor and the
environment factor. If you still can not realize synchronization after using
this software, you can use the other way such as controller
programming.
2.Operation
2.1. Key operation
MENU UP DOWN ENTER
Main key
【MENU】Main menu or back the last menu
【UP】Choosing data value
【DOWN】Choosing data value
【ENTER】Enter, choose the vice menu or end edit.
3


Combination key
Combination by 2 or more key. Such as “UP+DOWN” Press UP and DOWN
at the same time.
Combination key of “UP+DOWN” is different from “UP” or “DOWN”, it have
its own function.
Long press
Press the button for long time then leave.
2.2. Menu description
A. Main menu
LED show English
word/function
Key operation Description
Advanced DMX UP/DOWN key to choose the
address code (1~512)
ENTER key to save
check “channel
data”
Advance DMX
controller state
dMX
normal DMX
controller state
SLAve
equal“d001”
Above is the slave mode, attention:
1
、
Make sure there is only a signal (controller or master light)
2
、
The light will be turn off if the signal is cut down. (turn off the
controller or master light)
Cool white
(0~255)ENTER to choose
the led group
UP/DOWN to choose the
bright of the led group
Change color
4
Strobe UP/DOWN key to choose the
speed (1~50)
ENTER to save.
Strobe
Sound
Sound model
Above is the master state, the light will send the data automatically.
(the slave light should set “d001” or “SLAv”)
B. Current adjustment
1. Main menu
Under any main menu item, press and hold the MENU, after about 3 seconds
to enter the "keyboard current adjustment" mode, Then can adjust the
current . Proceed as follows:
1、First see the "r030". "R" stands for red, so only red will be lit at this time,
and the other colors will turn off automatically. "030" represents the
current current value, use the UP button or DOWN button to adjust from 0
to 255. Note that the slow increase, suitable for this: If the current is
too large, will lead to lamp beads burned!
2、After adjusting the red, press the "MENU" key to switch to "G030" began
to adjust the green, the same time it will only light green while the other
colors will automatically shut down ... ... The adjustment of other colors
and the like.
3、Press "ENTER" key to save and automatically return to "A001" menu
2. DMX Current regulation
Through the console (or host) for multiple lights current regulation. The
console for example, the following steps:
5