Mocka Nava Bedside Table User manual

Nava Bedside Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
1
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device
provided should fit most wall types, but please note that different wall materials may require different fixing
devices from those supplied.
bolt
x6
long
screw
x14
AB C DEFI
JKL M
H
Hardware Supplied
dowel
x12
locking
nut x6 x1
G
screw
x8
screw
x16
screw
x4
wedge
x4
hinge
x2
Wall Strap
x2
washer
Z
Y
wall
anchor
x1
X
safety
strap x1
WV
screw
x1
wall
screw
x1
bracket
cover
x1
x4
washer
N O
bolt
x4
Cover
x6
seal
x1
screw
x3
PQ
key x1
Allen
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
Phillips & Flathead screwdrivers
and hammer required
plastic
glide x4
R

Nava Bedside Table
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
2
12
Insert 6x bolts (C) into panel [1], and tighten with a screwdriver. Attach 1x bracket (E) to panel [5] and secure with 2x screws (P).
Tighten with a screwdriver. Place 1x cover (F) over bracket (E) as
shown.
C
C
C
C
1
C
C
E
P
5
F
E
P
P

Nava Bedside Table
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
3
34
Attach panels [3] ,[4] and [5] to panel [1] with 6x dowels (A). Secure with 6x
locking nuts (D) and tighten with a screwdriver. Insert 6x covers (N) into the
holes of panels [3] ,[4] and [5].
Slide panel [6] down along the grooves between the side panels [3] and [4].
A
AA
A
D
N
D
N
D
5
3
4
D
1
3
4
6

Nava Bedside Table
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
4
56
Attach panel [2] to the unit with 6x dowels (A), and secure with 6x long
screws (B). Tighten with a screwdriver.
Attach panels [9] to panels [7] and [8] with 16x screws (H).
Tighten with a screwdriver.
2
5
3
4
A
B
BB
BB
B
AA
AH
H
H
H
B
87
9
H

Nava Bedside Table
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
5
78
Attach panels [7] and [8] to panel [2] and secure with 8x long
screws (B). Tighten with a screwdriver.
Attach Legs [10] to panels [9] with 4x washers (M) and 4x bolts (L).
Tighten with the Allen key (Q). Attach 4x plastic glides (R) to the legs
using a hammer as shown.
10
L
M
9
L
M
BB
B
B
B
BB
B
2
7
8
Q
RR
R
R
R

Nava Bedside Table
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
6
910
Attach 2x hinges (K) to panel [11], securing with 4x screws (G) and attach
1x seal (O) using 1x screw (P) to panel [11]. Tighten with a screwdriver.
Secure panel [11] to panel [3] by attaching the other end of the 2x hinges
(K) with 4x screws (G) as shown. Tighten with a screwdriver. If the door is
not catching or sitting flush, twist the end of the cover (F) until it catches on
the seal (O).
11
K
GG
K
GG
G
G
G
3
F
P
O
NOTE: If the doors are uneven or
there is a gap in the middle, loosen
or tighten the screw on the door
hinge until they are sitting flush.

Nava Bedside Table
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
7
11 12
Attach 4x wedges (J) to the corners of the back panels [6] as shown, and
secure with 4x small screws (I). Attach 1x safety strap (V) to the back side
of the unit as shown using 1x washer (Z) and 1x screw (W). Tighten with a
screwdriver.
Once assembled lift furniture into place, do not drag. Attach the other end
of the safety strap (V) to the wall using 1x screw (Y), 1x wall plug (X) and
1x washer (Z). Tighten with a screwdriver. You’re done, enjoy!
V
Z
W
J
I
J
I
J
I
J
I
V
Z
W
J
I
Y
XZ
1
6