Motorline professional FIX Use and care manual

v3.0
REV. 08/2022
EN
USER’S AND INSTALLER’S MANUAL
FIX RAPID SELF-REPAIRING DOOR

1A 1B
ENEN
00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX STANDARDS TO FOLLOW
1B
4A
12
4B
7
10
4B
8
11
5
9
STANDARDS TO FOLLOW
INSIDE PACKAGE
LIMIT-SWITCHES ADJUSTMENT
TECHNICAL SPECIFICATIONS
INSTALLATION MAP
SAFE PROFILE FIXATION
MANUAL OPENING/CLOSING
SAFE PROFILE FIXATION
LATERAL GUIDES AND CONTROL BOARD FIXATION
DIMENSIONS - NORMAL KIT
LATERAL GUIDES AND CONTROL BOARD FIXATION
01. SAFETY INSTRUCTIONS
02. PACKAGE
06. LIMIT-SWITCHES
03. AUTOMATISM
04. INSTALLATION
05. INSTALLATION TUNNEL KIT
6
DIMENSIONS - TUNNEL KIT
INSTRUCTIONS FOR CONSUMERS / TECHNICIANS
07. TROUBLESHOOTING 13
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where they
purchased this product or the National Environment Agency
for details on where and how they can take these items
for environmentally safe recycling. Business users should
contact their vendor and check the terms and conditions
of the purchase agreement. This product and its electronic
accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.

2EN
01. SAFETY INSTRUCTIONS
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•Thismanual is intendedfirstlyforspecialized technicians, and does not
invalidate the user’s responsibility to read the “User Norms” section in
order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical,sensorialormentalcapacitiesarelower,orbypersonswithout
any knowledge of the product, provided that these are supervision
and instructions given by persons with experienced in terms of usage
of the product in a safe manner and who understands the risks and
dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points
to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•The centralmust be installed on asafe placeof anyfluid (rain, moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16

3EN
September 2009.
•Attach the permanent label for the manual release as close as possible
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
MOTORLINE ELECTROCELOS SA.
Travessa do Sobreiro, nº29
4755-474 Rio Côvo (Santa Eugénia)
Barcelos, Portugal
01. SAFETY INSTRUCTIONS
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information

4A 4B
ENEN
02. PACKAGE 03. AUTOMATISM
INSIDE PACKAGE TECHNICAL SPECIFICATIONS
Aluminum
Safe
Profile
Motor
cover
Lateral
Guides
Tarpaulin
Control
Board
The Self-Repairing Rapid Door FIX is built with its own white lacquered aluminum profiles.
It is certified to IP protection level.
User’s
Manual
TARPAULIN
• Yarn  x  dtex PES HT
• Weight  g/m
• Tensile Strenght / daN/ cm
• Tear Resistance / daN
• Operating temperature -C to C
MOTOR
• Power Supply V /Hz
• Power W
• Current ,A
• Rotational speed RPM
• Reduction :
• Noise dB
• Force Nm
• Operating temperature -C to C
• Protection class IP
• Working Frequency Intensive
• Insulation class Class F
Fixing
screws
Motor

5A 5B
185
300
250
97
97
33 33
510(PM) 550(PM)
540
390 275(OLM) 65(OLC) 390
335
560
340
243
65(OLC)270(OLM)
238 280
LVP
LVT - 66 LVP
LVT-66
LVT
AVP
AVP
400
A B A
A B
B
ENEN
03. AUTOMATISM 03. AUTOMATISM
DIMENSIONS - NORMAL KIT DIMENSIONS - FIX 5 KIT
Wall Wall
Lateral
guide
Lateral
guide
LEGEND
OLM • Motors side clearance
OLC • Opposite side clearance
PM • Minimum Lintel
LVP • Width of passageway
LVT • Overall width of passageway
AVP • Height of passageway
Dimensions shown in mm.
The dimensions of the
lateral guides and push
button are the same in the
Normal KIT and FIX 5 Kit.

6A 6B
96,65
96,65
32,65 32,65
510(PM) 550(PM)
540
390 275,65(OLM) 65(OLC) 390
335,23
560
340
243
64(OLC)??(OLM)
?? 280
LVP (LVT-65,3) LVP (LVT-65,3)
LVT
AVP
AVP
400
185
300
250
275 510
599
LVT
9696
LVP
LVT - 192
AVP
AVT - 510
AVT
739
3
2
1
ENEN
03. AUTOMATISM 03. AUTOMATISM
DIMENSIONS - TUNNEL KIT MANUAL OPENING/CLOSING
To open or close the door manually, simply pull and hold down the unlock and insert the crank, to
turn the screw installed at the bottom of the motor (see image).
• Turning to the right will open the door and turning to the left will close.
If you want, you can use a machine with an
umbrako key to open it faster.
LEGEND
PM • Minimum Lintel
LVP • Width of passageway
LVT • Overall width of passageway
AVP • Height of passageway
AVT • Overallheight of passageway
Dimensions shown in mm.
Wall Wall

7
1
3
5
16
4
16
2 2
6
15
7
8
6
10
11
13
14
12
9
EN
04. INSTALLATION
INSTALLATION MAP
 • Aluminum safe profile
 • Lateral Guides
 • Motor cover
 • Tarpaulin
 • Control Board
 • Safe profile
 • Motor
 • Connector Connections
 • Motor unlock lever
 • Emergency stop
 • Up button
 • Down button
 • Photocell fixation plate
 • Photocell
 • Photocell column
 • Strap

8
2
2
3
1
500mm
3
120mm
1
EN
04. INSTALLATION
SAFE PROFILE FIXATION
Center-aligned safe profile
2FIX SAFE PROFILE
Drill the holes at the marked locations, and then apply the safe profile to the wall,
fixing it with dowels and screws, suitable to the installation place.
The safe profile must be securely fixed to prevent accidents.
3 ADJUST TARPAULIN
Unlock the motor and pull the tarpaulin by
hand about 500mm (page 4B).
1POSITIONING SAFE PROFILE
Apply the safe profile to the wall of the installation site, paying attention to
the horizontal level and 120mm between the base of the support plate and the
beginning of the passageway.
Based on the holes in the support plates, mark the locations for drilling. The safe
profile should be centered with the passageway.
MINIMUM DIMENSIONS
NORMAL KIT
Minimum lintel - 510mm
Minimum side clearance (motor side) - 270mm
Minimum side clearance (opposite side) - 65mm
FIX 5 KIT
Minimum lintel - 550mm
Minimum side clearance (motor side) - 275mm
Minimum side clearance (opposite side) - 65mm
PASSAGEWAY

9
5
5
5
5
5
5
5
5
5
5
5
5
221mm
243mm
400mm
400mm
100mm
4
6
4
7
8
70mm
5
6C
B
A
8
EN
04. INSTALLATION
LATERAL GUIDES AND CONTROL BOARD FIXATION
4APPLY LATERAL GUIDES
Place the lateral guides by
placing them on the inside of
the support plates and leaning
against the wall.
The tarpaulin must be inside
the lateral guides so that it can
always go up and down inside.
5FIX LATERAL GUIDES TO
THE WALL
Fix the guides to the support
plates with screws.
The first screw should be
applied 100mm from the
ground and the remaining
one from 400 to 400mm.
6FIX CONTROL BOARD
Determine the location for fixing the
control board and fix it to the wall.
8PLACE MOTOR COVER
8.1 Tighten plate Bto plate A.
8.2 Fix the tether to plate A.
8.3 Fix plate Cto plate Band the tether.
8.4 Tighten the 2screws at the top of the cover.
Tether
Wall fixing
screws
7ADJUST SWITCH-LIMIT (PAGE 12)
WALL
PASSAGEWAY
PASSAGEWAY