Motorline professional LINCE300 Use and care manual

v12.0
REV. 08/2023
LINCELINCE EN
USER’S AND INSTALLER’S MANUAL

1A 1B
B
A
B
A
A
B
B

B


A

A

ENEN
ATTENTION:
. CONTENT . SAFETY INSTRUCTIONS
INDEX STANDARDS TO FOLLOW
. INSTALLATION
STANDARDS TO FOLLOW
INSIDE PACKAGE
CHANGE MOTOR DIRECTION
MANUAL RELEASE
TECHNICAL SPECIFICATIONS
. SAFETY INSTRUCTIONS
. PACKAGE
. AUTOMATION
V/V MOTOR
V MOTOR
MAINTENANCE
FINAL CONSUMERS INSTRUCTIONS
INSTRUCTIONS FOR SPECIALIZED INSTALLERS
. COMPONENTS TEST
. MAINTENANCE
. TROUBLESHOOTING
HEIGHT OF THE SUPPORTS
EXTERNAL OPENING INSTALLATION DIMENSIONS
INSTALLATION STEPS
INSTALLATION MAP
INTERIOR OPENING INSTALLATION DIMENSIONS
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances
in electrical and electronic equipment and with Delegated
Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed of
as other household waste at the end of its useful life. To avoid
possible harm to the environment or human health resulting
from the uncontrolled disposal of waste, separate these items
from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources. Home
users should contact the dealer where they purchased this
product or the National Environment Agency for details on
where and how they can take these items for environmentally
safe recycling. Business users should contact their vendor and
check the terms and conditions of the purchase agreement.
This product and its electronic accessories should not be
mixed with other commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling the
product and observe all safety procedures in this manual.

2EN
. SAFETY INSTRUCTIONS
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•This manual is intended firstly for specialized technicians, and does
not invalidate the user’s responsibility to read the “User Norms”
section in order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and
other mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical, sensorial or mental capacities are lower, or by persons
without any knowledge of the product, provided that these are
supervision and instructions given by persons with experienced in
terms of usage of the product in a safe manner and who understands
the risks and dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points
to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if
the necessary mechanical stops are in the appropriate places.
•Thecentralmustbeinstalledonasafeplaceofanyfluid(rain,moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16
September 2009.

3EN
. SAFETY INSTRUCTIONS
•Attachthe permanent label forthe manualrelease as close as possible
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•If the system requires any repair or modification, unlock the
automatism, turn off the power and do not use it until all safety
conditions have been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in
in motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if
the product is in motion.
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
MOTORLINE ELECTROCELOS SA.
Travessa do Sobreiro, nº29
4755-474 Rio Côvo (Santa Eugénia)
Barcelos, Portugal

4A 4B
mm (LINCE)
mm (LINCE)
mm
mm
ENEN
 • Loosen the  screws that fix the Lower Part to
Middle Part.  • Remove Lower Part.
This automatism is a product developed exclusively for the automatic opening of swing gates.
Besides being pratical, safe and powerful, this product has a new function incorporated so that you can
transform a motor to apply on right leaves to left leaves.
This allows greater flexibility in the use of each motor.
Motor disassembly and assembly process, in order to transform motor, must be done as follows:
Upper part Middle part
Lower part
. PACKAGE . AUTOMATION
INSIDE PACKAGE CHANGE MOTOR DIRECTION
In the package you will find the following components:
•  Motors
•  Front supports
•  Remote
controls
•  Control board
•  Rear supports
•  Photocells set
•  Release keys
•  Capacitors
[Only available with the v
(f) and v(f) models]
•  User’s manual

5A 5B
ENEN
 • Loosen the  screws of the Middle Part.  • Remove the plastic cover from the back.
 • Insert Release key on the unlock shaft.  • Rotate key   in the direction indicated in
the figure to unlock.
 • Automation unlocked.
Note • To lock automation so it can work
automatically, must do it by turning the key
anticlockwise.
Information engraved on the unlock shaft.
DUnlock || BLock
 • Rotate Upper Part .  • Assemble automation by tightening all
components with the screws.
 • Completely transformed automation.
 • Remove Middle Part.
. AUTOMATION . AUTOMATION
CHANGE MOTOR DIRECTION MANUAL RELEASE

6A 6B
mm || mm || mm
mm || mm || mm
mm
mm
mm
A
A
BB
ENEN
The automation must be installed with a small inclination, to prevent water infiltration through the
extension arm.
For this, the front support must be fixed to the gate with a height lower than the height of the rear
support. See example below:
Dimension A • Vertical distance from the floor to the top of the rear support .
Dimension B • Vertical distance from the floor to the top of the front support.
It is very important that these dimensions are respected! Only this way can be assured the
correct functioning and durability of the automation!
It is also very important to have a levelled ground/terrain!
Model LINCE LINCE LINCE
• Power Supply
V Vac /Hz Vac /Hz Vac /Hz
V Vac /Hz Vac /Hz Vac /Hz
V Vdc Vdc Vdc
• Power /V W W W
V W W W
• Current
V ,A ,A ,A
V ,A ,A ,A
V A to A A to A A to A
• Rotational speed /V  RPM  RPM  RPM
V  RPM  RPM  RPM
• Noise level LpA   dB (A) LpA   dB (A) LpA   dB (A)
• Force N N N
• Operating temperature -C to C -C to C -C to C
• Thermal protection C C C
• Protection class IP IP IP
• Working frequency /V   
V Intensive Intensive Intensive
• Opening time  sec. to  sec.  sec. to  sec.  sec. to  sec.
• Course mm mm mm
• Max leaf length mm mm mm
• Capacitor V F F F
V F F F
• Opening speed V mm/s mm/s mm/s
V ,mm/s ,mm/s ,mm/ss
. AUTOMATION . INSTALLATION
TECHNICAL SPECIFICATIONS HEIGHT OF THE SUPPORTS
A? mm It can be any dimension of your choice.
BA-mm mm below level dimension A.
Example:
If the height of the rear support (dimension A) is set at mm, then the height of the front support
(dimension B) will be mm (mm-mm).
The dimensions of the automation in the  ||  ||  versions are as follows:

7
X
W
Y
 (W:   )
YX
               
                
                
                
                
               º
              
             
            
           
         
      
   
 (W:   )
YX
      
       
       
      
    
   
 
 (W:   )
YX
  
   
  
 
EN
INTERIOR OPENING INSTALLATION DIMENSIONS
. INSTALLATION
In the diagrams illustrated below and on the next page, the dimensions for the installation of
automations are defined.
It is very important that these dimensions are respected! Only this way can be assured
the correct functioning and durability of the automation!
(EXTERIOR)
(INTERIOR)
Axis of rotation of the
motor, on the rear support
Opening
direction
Axis of rotation of the gate
(hinge axis)
Axis of rotation of the
motor, on the front support
Stopper at the
closing of the gate
Stopper at the opening of
the gate (Optional)
When installing the automation, it is mandatory to respect the dimensions x and y, indicated
in the tables. Within this area, it is possible to identify the maximum opening angle that the
gate reaches in these dimensions.
X, Yand Wshown in (mm)
Dimension X Horizontal distance between hinge axis of the gate and the rear axle of the motor.
Dimension Y Vertical distance between hinge axis of the gate and the rear axle of the motor.
Dimension W Distance between axis of the motor supports.
LEGEND

8
 (W:   )
YX
             
              
              
              
             
             
             
            
            
            
           
           
          
         
        
       
      
 (W:   )
YX
      
       
       
      
     
     
    
   
  
  
 (W:   )
YX
  
   
  
 
 
X
YW
EN
. INSTALLATION
In the diagrams illustrated below and on the next page, the dimensions for the installation of
automations are defined.
EXTERNAL OPENING INSTALLATION DIMENSIONS
(EXTERIOR)
(INTERIOR)
Axis of rotation of the gate
(hinge axis)
Axis of rotation of the motor, on the front
support
Stopper at the
closing of the gate
Axis of rotation of the
motor, on the rear support
Opening
direction
*Stopper at the
opening of the gate
It is very important that these dimensions are respected! Only this way can be assured
the correct functioning and durability of the automation!
When installing the automation, it is mandatory to respect the dimensions x and y, indicated
in the tables. Within this area, it is possible to identify the maximum opening angle that the
gate reaches in these dimensions.
X, Yand Wshown in (mm)
Dimension X Horizontal distance between hinge axis of the gate and the rear axle of the motor.
Dimension Y Vertical distance between hinge axis of the gate and the rear axle of the motor.
Dimension W Distance between axis of the motor supports.
LEGEND
Placing a stopper in the
opening is recommended.

9A 9B
ENEN
Pay attention to installation dimensions mentioned on pages B,  and !
 • Fix rear support
 • Install automation on the supports
 • Test movement
 • Connecting automation to control board
and configuring control devices.
 • Fix front support
 • Remove covers and dowels from motor
• The Rear support must be fixed to the pillar or wall
using dimensions provided in the previous pages.
It can be fixed using screws with mechanical bushing
or chemical welding process, or one of your choice
since that provides proper fixation of the support.
• The automation must be placed on both supports
at the same time to avoid leaving the automation
suspended by only one of the supports.
To make the task easier, you should unlock the
automation in order to be able to extend/retract arm
easily (see page B),to get the correct position for
supports.
• Install the dowels removed earlier on each place with
a small amount of lubricant for less friction.
• Move the gate by hand to check that the gate opens
and closes without any hindrance.
This will ensure that automation is not subjected to
problems during operation.
• With the automation installed, connect it to control
board for system configuration (see control board
user manual).
Must also configure the desired control devices
(remote controls, push button, etc.) and other
additional components such as antenna, flashing
lamp, key selector, among others.
• The Front support should be fixed to the gate,
respecting height dimensions and distance to the rear
support.
This may be fixed by using screws, welding process, or
another one of your choice, as long as it provides a
proper fixation of the support.
• Before installing motor, remove covers and dowels
from motor.
• At the end of the installation, put back plastic covers
for a better visual finish of the automation.
It is important to respect this installation order!
Otherwise, it is not possible to ensure correct installation and automation may not work pro-
perly!
. INSTALLATION . INSTALLATION
INSTALLATION STEPS INSTALLATION STEPS
SECURITY NOTICE
At the end of the installation, insulate all the holes for
passing the cables, to prevent the entry of animals and
parasites.
Otherwise, it may jeopardize the proper functioning of
the equipment.

10 EN
• JUNCTION
BOX
. INSTALLATION
INSTALLATION MAP
• INTERIOR
PHOTOCELLS • EXTERIOR PHOTOCELLS
• EXTERIOR
PHOTOCELLS
• KEY
SELECTOR
• MOTOR • FLASHING
LAMP • ANTENNA • CONTROL BOARD
LEGEND:
• Connection cables
It is important to use stoppers at the opening and closing of the gate. If not respected, compo-
nents of the automation may suffer efforts for which they were not prepared, and as a result
will be damaged.
It is important to use junction boxes for connections between motors, components and con-
trol board. All cables must enter and exit on the bottom of the junction and control board
boxes.

11 EN
Anomaly Procedure Behavior Procedure II Discovering the origin of the problem
• Motor
doesn't work •Make sure you have power in the
automation control
board and if it is
working properly.
• Still not working • Consult a qualified
MOTORLINE technician. 1 • Open control board and check if it has V/V/V power supply;  • Check input fuses;
 • Disconnect motors from control board and test them by connecting directly to power supply in order to find out if they have problems (see page
A/B).
 • If the motors work, the problem is on the control board. Consult the control board manual;
 • If the motors doesn’t work, remove them from installation site and send to our MOTORLINE technical services for diagnosis.
• Motor
doesn’t move
but makes
noise
• Unlock motor and
move gate by hand to
check for mechanical
problems on the
gate.
• Is the gate stuck? • Consult an experienced
gate expert 1 • Check all motion axis and associated motion systems related with gate and automation (dowels, hinges, etc.) to find out what is the problem.
• Gate moves easily? • Consult a qualified
MOTORLINE technician. 1 • Check capacitors, testing automation with new capacitors;  • If capacitors are not the problem, disconnect motors from control board and test them by connecting directly to power supply in order to find out if
they have problems (see page A/B).
 • If the motors work, the problem is in control board.
Pull it out and send it to our MOTORLINE technical services for diagnosis;
 • If the motors doesn’t work, remove them from installation site and send to our MOTORLINE technical services for diagnosis.
• Motor opens
but doesn’t
close
• Unlock motor and
move gate by hand to
closed position.
Lock motor(s) again
and turn off power
supply for  seconds.
Reconnect it and send
order to open gate
using remote control.
• Gate opened but
didn’t close again. 1 • Check if there is any obstacle in front of the
photocells;
 • Check if any of the control
devices (key selector, push
button, video intercom, etc.)
of the gate are stuck and
sending permanent signal to
control board;
 • Consult a qualified
MOTORLINE technician.
All MOTORLINE control boards have LEDs that easily allow to conclude which devices are with anomalies.
All safety devices LEDs (LE/LA) in normal situations remain On.
All "START" circuits LEDs (LO/LS) in normal situations remain Off.
If LEDs devices are not all On, there is some security systems malfunction (photocells, safety edges), etc.
If "START" circuits LEDs are turn On, there is a control device sending permanent signal.
A) SECURITY SYSTEMS:
1 • Close with a shunt all safety systems on the control board (check manual of the control board).
If the automated system starts working normally check which device is problematic.
 • Remove one shunt at a time until you find the malfunction device .
 • Replace it for a functional device and check if the automation works correctly with all the other devices. If you find another one defective, follow the
same steps until you find all the problems.
B) START SYSTEMS:
 • Disconnect all wires connected to the START connector.
 • If the LED turned Off, try reconnecting one device at a time until you find the defective device.
NOTE:
In case procedures described in sections A) and B) don’t result, remove control board and send to our technical services for diagnosis.
• Motor
doesn’t make
complete
route
• Unlock motor and
move gate by hand to
check for mechanical
problems on the
gate.
• Encountered
problems? • Consult an experienced gate expert 1 • Check all motion axis and associated motion systems related with gate and automation (dowels, hinges, etc.) to find out what is the problem.
• Gate moves easily? • Consult a qualified
MOTORLINE technician. 1 • Check capacitors, testing with new capacitors;  • If capacitors are not the problem, disconnect motors from control board and test them by connecting directly to power supply in order to find out if
they are faulty;
 • If the motors doesn’t work, remove them from installation site and send to our MOTORLINE technical services for diagnosis.
 • If motors work well and move gate at full force during the entire course, the problem is in the control board. Set force on the control board. Make a
new working time programming, giving sufficient time for opening and closing with appropriate force (see manual of the control board).
 • If this doesn’t work, remove control board and send it to MOTORLINE technical services services.
NOTE: Setting force of the control board should be enough to open and close the gate without stopping, but should stop with a little effort from a
person.
In case of safety systems failure, the gate can never cause physical damage to obstacles (vehicles, people, etc.).
. TROUBLESHOOTING
FINAL CONSUMERS INSTRUCTIONS INSTRUCTIONS FOR SPECIALIZED INSTALLERS

12A 12B
3
22
1
A
B
C
8F (230V) / 20F (110V)
1
2
3
ENEN
To detect if the malfunction is on the control board or on the motor is, sometimes, necessary to perform
tests with direct connection to a V/V power supply.
For this, it is necessary to intercalate a capacitor on the connection in order to the automatism to work
(check the type of capacitor to be used in the product manual). The diagram below, shows how to make
that connection and how to intercalate the different components wires.
Connect the power wires to the terminal, as shown below.
Connect the automatism wires in the terminal, intercalate a capacitor in the opening and closing
wires.
Once these connections are completed, connect to a 110V/230V power plug, depending on the motor/
control board in test.
All tests must be performed by specialized technicians due to serious danger associated with
the bad use of electrical systems!
All tests must be performed by specialized technicians due to serious danger associated with
the bad use of electrical systems!
. COMPONENTS TEST . COMPONENTS TEST
V/V MOTOR V MOTOR
V Battery
V Battery Motor rotates to one
direction (eg: right) Motor rotates in the opposite direction
(eg: left)
V Battery
Motor's wires
Motor
Ground Wire
Phase 1
Phase 2
Power Supply 2
Power Supply 1
Capacitor
LEGEND:
A. Black
B. Grey
C. Brown
To detect which are the components with problems in a V automatism installation, it's sometimes
necessary to run a test directly to a external power supply (V battery).
The diagram below shows how to make this connection.
NOTES:
• To make these tests it isn't necessary to remove it from the location where it is installed, because in
this way, you can understand if the automation connected directly to the external battery is able to
work correctly.
• Once you connect the wires to a battery V, the motor must work for one direction. To test the opposite
movement, change the position of the wires connected to the battery.
NOTES:
• To perform the tests, there is no need to remove the automatism from the place it is
installed, because in this way, it is possible to understand if the automatism can function
properly connected directly to the power.
• You should use a new capacitor during this test to ensure that the problem is not with the
capacitor.
Neutral
Neutral

13 EN
CLEAN THE TUBE
LUBRICATE DOWELS
CHECK MOTOR SUPPORTS
• With a cloth soaked in lubricant spray, clean all the
residues that accumulate in the automation tube.
• Apply a small amount of lubricant spray on the tube and
using a dry cloth remove the excess, leaving an even layer
on the tube.
• Remove front and rear covers
• Place a small amount of lubricant on the holes that
contains support dowels.
• Install covers on the respective holders.
• Make sure that supports remain well fixed on the pillars
and gate to ensure proper functioning of the equipment.
These maintenance measures must be applied every year in order to insure proper functioning
of the automation.
. MAINTENANCE
MAINTENANCE