Motorola MINITOR VI RLN6506 Series User manual

EN FRC

blank.fm Page 1 Wednesday, September 18, 2013 3:39 PM

1English
IMPORTANT SAFETY INSTRUCTIONS
This document contains important safety and operating instructions. Please read these instructions
carefully and save them for future reference.
Before using the battery charger, read all the instructions and cautionary markings on (1) the charger, (2) the
battery, and (3) on the pager using the battery.
WARNINGS
1. To reduce risk of injury, charge only the rechargeable Motorola-authorized batteries listed
in Table 1. Other batteries may explode, causing personal injury or damage.
2. Use of accessories not recommended by Motorola may result in risk of fire, electric shock,
or injury.
3. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the
cord when disconnecting the charger.
4. An extension cord should not be used unless absolutely necessary. Use of an improper
extension cord could result in risk of fire or electric shock. If an extension cord must be
used, make sure that the cord size is 18 AWG for lengths up to 100 feet (30.48 m) and
16 AWG for lengths up to 150 feet (45.72 m).
5. To reduce risk of fire, electric shock, or injury, do not operate the charger if it has been
broken or damaged in any way. Take it to a qualified Motorola service representative.
W A R N I N G
68012010008_b.book Page 1 Tuesday, May 6, 2014 2:07 PM

2
English
WARNINGS (CONTINUED)
6. Do not disassemble the charger; it is not repairable and replacement parts are not
available. Disassembly of the charger may result in risk of electrical shock or fire.
7. To reduce risk of electric shock, unplug the charger from the AC outlet before attempting
any maintenance or cleaning.
8. To reduce risk of injury, use charger with Motorola authorized power supplies listed in
Table 2.
9. This is a Class A product. In a domestic environment, this product may cause pager
interference in which case the user may be required to take adequate measures.
OPERATIONAL SAFETY GUIDELINES
• This equipment is not suitable for outdoor use. Use only in dry locations/conditions.
• Ensure the pager is dry before inserting into the Amplifier Charger.
• Connect equipment only to an appropriately fused and wired supply of the correct voltage (as specified on
the product). Disconnect from line voltage by removing main plug.
• The socket outlet to which this equipment is connected should be close by and easily accessible.
• In equipment using fuses, replacements must comply with the type and rating specified in the equipment
instructions.
• Maximum ambient temperature around the power supply equipment must not exceed 40 °C (104 °F).
• Output power from the power supply unit must not exceed the ratings stated on the product label located
on the bottom of the charger.
• Make sure the cord is located where it will not be stepped on, tripped over, or subjected to water, damage,
or stress.
W A R N I N G
68012010008_b.book Page 2 Tuesday, May 6, 2014 2:07 PM

3English
BRIEF DESCRIPTION
The Amplifier Charger is intended for use with the Motorola-approved Lithium-ion rechargeable batteries
(listed in Table 1). The front pocket of the charger is capable of handling a pager with an attached battery. The
rear pocket is designed only to charge the above mentioned batteries (alone).
An illuminated LED indicates the state of charge for the front and rear pocket.
OPERATIONAL GUIDELINES
• Always remember to power the Amplifier Charger first before inserting the pager with the attached battery
into the front pocket or the auxiliary battery into the charger's rear pocket.
• The front pocket has charging priority over the rear pocket. Therefore, the rear pocket may not charge at
its full rate until the front pocket charging is complete.
• The Amplifier Charger is not designed to accommodate the alkaline battery tray.
MOTOROLA-AUTHORIZED BATTERIES
The batteries listed in Table 1 is approved for use with the Amplifier Charger.
Note: The Amplifier Charger is not designed to accommodate the alkaline battery tray.
Table 1: Motorola-Authorized Batteries
Kit (Part) Number Platform/Description
PMNN4438_ Battery, Li-Ion (UL Battery)
PMNN4451_ Battery, Li-Ion (Non-UL Battery)
68012010008_b.book Page 3 Tuesday, May 6, 2014 2:07 PM

4
English
MOTOROLA-AUTHORIZED POWER SOURCES/POWER SUPPLIES
The power supply listed in Table 2 is approved for use with the Amplifier Charger.
MOTOROLA-AUTHORIZED ANTENNAS
The antennas listed in Table 3 is approved for use with the Amplifier Charger.
MOTOROLA-AUTHORIZED CHARGER
Table 2: Motorola-Authorized Power Supply
Power Supply
Kit Number Description
EPNN9288A Switch Mode PS, NA, LA
Table 3: Motorola-Authorized Antennas
Kit (Part) Number Platform/Description
RLN6507_ Antenna, Charger AMP, MIN VI VHF
RLN6508_ Antenna, Charger AMP, MIN VI UHF
Table 4: Motorola Authorized Charger
Charger Kit
Number Charger Description
PMLN6465_ Amplifier Charger Base
68012010008_b.book Page 4 Tuesday, May 6, 2014 2:07 PM

5English
STANDARD FEATURES
External Antenna
The external antenna input jack (BNC connector) is located on the rear of the Amplifier Charger housing. An
external antenna must be attached to the Amplifier Charger for maximal reception.
Audio Amplifier
The Amplifier Charger contains a 2.5-watt audio amplifier and speaker. When a pager is placed in the
Amplifier Charger, the audio is routed to the Amplifier Charger speaker rather than to the pager speaker.
External Speaker Jack
An external speaker jack, located on the rear of the Amplifier Charger housing, allows the user to attach an
external speaker. When an external speaker is connected, audio will be routed to that speaker rather than to
the Amplifier Charger internal speaker. The minimum speaker impedance is 4 ohms.
Relay
The Amplifier Charger includes a relay that is energized whenever an alert is received, and a 6-pin DIN
accessory connector is located on the rear of the unit. The 6-pin mating plug for these models may be wired
to provide the following functions:
•Remote Speaker Audio (Pins 1 and 6)
An external 4-ohm speaker may be connected to the Amplifier Charger via pin 1 (audio) and pin 6 (ground
return) of the plug, to provide both remote speaker audio and internal speaker audio at the same time.
•Relay Dry Contact Closure (Pins 2 and 3)
When the accessory relay is energized, its contacts close and present a short across pins 2 and 3 of the
connector. The relay contacts are rated for 10 watts maximum at 28 VDC/ACRMS. Within the limits of the
68012010008_b.book Page 5 Tuesday, May 6, 2014 2:07 PM

6
English
10-watt rating the closed contacts can handle up to 750 mA continuously and switch up to 400 mA of
current. Relay contact rating: 750 mA maximum @ 28 VDC.
•Relay Closure Timing Control (Pins 4 and 5)
Accessory connector, pins 4 and 5, are used to select the time duration of the relay contact closure. If
these two pins are not used (open circuit), the relay remains energized for approximately 10 seconds after
an alert is received or until the reset button is pressed, whichever comes first. If pins 4 and 5 are shorted,
the relay remains energized until the reset button on the front of the Amplifier Charger is pressed.
Pressing the reset button causes the contacts to open to turn off the ALERT indicator.
ACCESSORY
PIN 6
Ground (Audio)
PIN 3
Relay Dry Contact
PIN 5
Relay Closure Timing
PIN 1
Audio
PIN 4
Relay Closure Timing
PIN 2
Relay Dry Contact
Figure 1: Overview of the 6-Pin DIN Accessory Connector
68012010008_b.book Page 6 Tuesday, May 6, 2014 2:07 PM

7English
OPERATING INSTRUCTIONS
Amplifier Chargers are intended for use only with the authorized Motorola batteries and power
supplies listed in Table 1 and Table 2; usage with unauthorized products may prevent proper
operation and may damage the device.
The battery charger will accommodate a pager with an attached battery in the front pocket, and a battery
alone in the rear pocket. To charge a battery, use the following procedure:
1. Plug the round end of the power supply cord into the DC Connector on the back of the charger.
2. Plug the power supply into the appropriate AC outlet. The spare battery LED and pager battery LED will
flash single green once and the alert LED will flash single red once to indicate a successful power-up.
3. Insert a pager with battery into the charger's front pocket by:
a. aligning the groove on each side of the pager with the corresponding raised rail on each side of the
charger pocket.
b. sliding the pager into the charger pocket, ensuring complete contact between the charger and pager
contacts.
4. When the pager is properly seated in the pocket, the charger LED will light in accordance with Table 5 on
page 10.
Note:
• Charge new batteries overnight to ensure full charge. To minimize charge time, it is recommended to turn
the pager OFF.
• The Amplifier Charger is not designed to accommodate the alkaline battery tray.
• During receipt of a page, the LED may flash amber, indicating charging has temporarily been suspended.
68012010008_b.book Page 7 Tuesday, May 6, 2014 2:07 PM

8
English
5. Insert a battery into the charger’s rear pocket by:
a. aligning the groove on each side of the battery with the corresponding raised rail on each side of the
charger pocket.
b. sliding the battery into the charger pocket, ensuring complete contact between the charger and
battery contacts.
6. When the battery is properly seated in the pocket, the charger LED will light in accordance with Table 5
on page 10.
Note:
• Charge new batteries overnight to ensure full charge.
• The Amplifier Charger is not designed to accommodate the alkaline battery tray.
68012010008_b.book Page 8 Tuesday, May 6, 2014 2:07 PM