National Cycle VStream+ N20133 Service manual

National Cycle, Inc. PO Box 158 Maywood, IL 60153-0158 USA P: 708-343-0400 / F: 708-343-0625 / E: [email protected] www.nationalcycle.com
©2019 ational Cycle, Inc. Page 1 of 4 10-110804-000 11/19
Thank you for urchasing a National Cycle roduct. Read these instructions carefully and thoroughly before beginning work. Dealers, if installing this
windshield for a customer, lease give them this manual u on com letion. It contains information needed to ro erly maintain and use this roduct.
INSTALLATION INSTRUCTIONS/OWNERS MANUAL
VStream+® Windscreens for Kawasaki® Z650
N20133 VStream+, Dark Tint, Sport
N20134 VStream+, Light Tint, Sport-Tour
N20135 VStream+, Clear, Touring
Made in USA
ARTS LIST
ITEM ART NO. DESCRI TION QUANTITY
A Windscreen; 3.0mm Polycarbonate 1
B 37-374484-000 VStream+ Mounting Bracket; Black 1
C 20-290807-000 Gauge Cover/Visor; Black 1
TOOLS REQUIRED
4mm Allen Wrench
5mm Allen Wrench
10mm Socket with 4-Inch Extension
ALL OEM FASTENERS
WILL BE REUSED.
Figure 1
Figure 2 Figure 3
A
BC
RE ARATION
With a 4mm Allen Wrench, remove the four 5x16 Bolts and
ylon Washers securing the OEM Meter Cover (mini-wind-
screen) to the Meter Stay. This component will not be reused.
Figure 1
Use a 10mm Socket and Extension to remove the three 6x12
Flanged Bolts securing the OEM Meter Stay to the bike.
Figure 2
Pull the wiring harness free from instrument panel to allow the
Meter Stay to be removed. This component will not be reused.
Figure 3
ow reconnect the wiring harness connector back into the rear
of the instrument panel.
VStream® Windscreen Patent No. 7,387,328

National Cycle, Inc. PO Box 158 Maywood, IL 60153-0158 USA P: 708-343-0400 / F: 708-343-0625 / E: [email protected] www.nationalcycle.com
©2019 ational Cycle, Inc. Page 2 of 4 10-110804-000 11/19
RE ARATION; CONT’D.
Figure 4
Remove the four 5mm Wellnuts from the OEM Meter Stay.
INSTALLATION
Figure 5
Insert the four 5mm Wellnuts from Figure 4 into the four outer
mount points of the VStream+ Mounting Bracket (B).
Figure 6
Use a 5mm Allen Wrench to remove the two 6x12 Bolts secur-
ing the Upper Headlight Bracket and Upper Cowling to the
motorcycle. Remove only these two Bolts for reinstallation in the
next step.
Figure 7
Position the VStream+ Mounting Bracket (B) as shown and rein-
stall the two 6x12 Bolts with a 5mm Allen Wrench.
Figure 8
With a 10mm Socket and Extension, reinstall the top two 6x12
Flanged Bolts removed in Figure 1.
The third 6x12 Flanged Bolts removed at the bottom in Figure 1
is no longer required. But if you thread it into its original location
and tighten it down, you’ll never wonder where it went.
ow that the VStream+ Mounting Bracket (B) is installed, make
sure the two 6x12 Bolts (5mm Allen Wrench) and two 6x12
Flanged Bolts (10mm Socket) are tightened securely.
Figure 4 Figure 5
Figure 6
Figure 7
Figure 8
B

National Cycle, Inc. PO Box 158 Maywood, IL 60153-0158 USA P: 708-343-0400 / F: 708-343-0625 / E: [email protected] www.nationalcycle.com
©2019 ational Cycle, Inc. Page 3 of 4 10-110804-000 11/19
Figure 9
Figure 10
Figure 12 Figure 13
INSTALLATION; CONT’D.
Figure 9
ow you will begin installation of the Gauge Cover/Visor (C).
Begin by removing the paper backing from the adhesive Velcro®
strips attached to the inside of the the Gauge Cover/Visor.
Figure 10
ow install the Gauge Cover/Visor (C) onto the bike’s Meter
Case Cover, with the bottom of the Visor flush with the bottom
leading edge of the Meter Case Cover.
Figure 11
Press firmly at the Velcro® attachment points to get a good
Hook/Loop connection and to firmly adhere the adhesive back-
ing of the Velcro® strips to both the Gauge Cover/Visor and the
bike’s Meter Case Cover.
Figure 12
With a 4mm Allen Wrench in hand, and the four 5x16 Bolts and
ylon Washers removed at the start of PREPARATION, position
your new VStream+ Windscreen (A) onto the VStream+
Mounting Bracket (B).
Figure 12
Install the Bolts/Washers through the Windscreen and into the
5mm Wellnuts in the Bracket. It may help to reach a finger
behind the Bracket to hold each Wellnut in place as you thread
the Bolt into it.
Install each 5x16 Bolt just finger-tight until all four are in place.
Then tighten all four securely.
Now go out and enjoy the ride!
C
A
Figure 11
C

CLEANING AND MAINTENANCE
To clean the screen, wash with a clean soft cloth and plenty of warm water
and, if necessary, a non-abrasive soap such as dishwashing liquid. Flannel or
soft chamois ma e good cleaning cloths. Paint, glue residue or grease
removal: Moisten cotton wad with naphtha or turpentine followed by a wash as
above.
National Cycle Shield Wash™ (N1401-01) ma es a good daily cleaner and
comes with a handy travel-size bottle. Shield Wash is safe for all windshields
and helmet visors
Do not clean polycarbonate in hot sun or high temperatures. Do not clean the
screen with household glass cleaners. Do not allow bra e fluid, alcohol, or
strong solvents to contact the screen.
RAIN REPELLENT
Do not use rain protective products made for glass. We recommend National
Cycle’s RainZip® (N1410-01) to eep your windscreen clear in rainy weather.
Register Your Windshield Online at www.nationalcycle.com
National Cycle 3-Year Limited Warranty
National Cycle hereby warrants to the original registered owner of a National Cycle polycarbonate windshield for a period of three years from the date of
purchase against brea age. This limited warranty is expressly limited to the replacement of the polycarbonate windscreen. This limited warranty does not
include scratches, coating failure, cosmetic wear and tear, replacement of hardware, or any consequential damages or expenses including labor cost of
installation, removal and/or replacement, inconvenience, inbound freight expenses or damage to any other component of the motorcycle or any other acces-
sories. Certain chemicals, generally nown as acidic hydrocarbons, are nown to cause polycarbonate damage and will not be covered under this limited
warranty. Please refer to the cleaning instructions supplied with all National Cycle windshields.
Visit www.nationalcycle.com for further details, or call or write National Cycle
Never ride your motorcycle with loose accessory mounting hardware. Chec the hardware for tightness regularly.
Today's motorcycles are built with enough frame rigidity to withstand the moderate loads imposed on them by the foreseeable addition of an accessory(ies). If an accessory(ies)
adversely affects your motorcycle's stability, immediately remove the accessory(ies). Do not ride a motorcycle that exhibits unsafe handling traits.
Have experienced service personnel correct any problem before riding with the accessory(ies) installed. For further questions concerning handling problems associated with an
accessory(ies), contact your dealer, motorcycle manufacturer, or accessory manufacturer.
Sunlight reflected off the inside curvature of the windscreen can, at certain times of day, cause extreme heat buildup on the motorcycles instruments and possibly even
melt them. Exercise care in parking to avoid this. Park your motorcycle facing the sun or place an opaque ob ect over this area.
WARNING
National Cycle, Inc. PO Box 158 Maywood, IL 60153-0158 USA P: 708-343-0400 / F: 708-343-0625 / E: [email protected] www.nationalcycle.com
©2019 ational Cycle, Inc. Page 4 of 4 10-110804-000 11/19