National Cycle SwitchBlade Deflector UQ01 User manual

Parts List For: Kit UQ01, Kit UQ05, Kit UQ07
Note: Your specific Mount Bracket number is specified
in Index 1 and 2.
The items pre-assembled to the windscreen are prop-
erly tightened using thread lock. Do not adjust.
INDEX PART NO. AND DESCRIPTION QTY.
1 37-371931-000 Mount Bracket, Left KIT UQ01 1
1 37-371935-000 Mount Bracket, Left KIT UQ05 1
1 37-371937-000 Mount Bracket, Left KIT UQ07 1
2 37-371932-000 Mount Bracket, Right KIT UQ01 1
2 37-371936-000 Mount Bracket, Right KIT UQ05 1
2 37-371938-000 Mount Bracket, Right KIT UQ07 1
BAG 761 Contained in KIT UQ01, UQ05, UQ07
3 55-586043-000 Bolt, Carriage 5/16”-18 x 5/8” 4
4 42-482201-000 Nut, Hex Cap 5/16 - 18 4
1, 9/16” Socket
1, Socket Wrench
Attention Note:
Special notes and cautionary measures which
can prevent damage to the accessory or
motorcycle.
Tips for facilitation of operation, control and
adjustment, as well as maintenance work.
SwitchBlade Deflector™ Windshield
Lexan® polycarbonate with QUANTUM™ Coating
This installation manual covers Kit UQ01, Kit UQ05 and Kit UQ07
Dealers: If installing this windshield for a customer, please give them this manual. It contains information needed to
properly maintain and use this product.
The SwitchBlade Deflector is intended for use with the correct QuickSet 4™ mount kit for your motorcycle. At any time you
may interchange windshields with the 2-Up™ or Shorty™ using the same mount kit. All Patents Pending
Position the motorcycle securely on its stand or a work stand. Cover
the front fender and fuel tank with a suitable cloth to avoid scratch-
es from dropped tools.
Preparation
Page 1 of 2 10-112210-000 07/04
Figure 1.
12
3 4
Left and right side of motorcycle and product are
determined while sitting on the bike.

INSTALLATION
ATTACH THE BRACKETS TO THE WINDSHIELD
When properly identified and installed, Bracket bends
outboard. Bracket mounts outboard to the pre-assem-
bled windshield mount as well.
1. Identify right side Bracket (2).
2. Assemble right Bracket to right side of windshield with Carriage
Bolts (3) and Nuts (4). Be certain Bolt neck seats correctly in Bracket.
(9/16 Socket and Wrench) Figure 2.
ADJUST BRACKETS, TIGHTEN TO “HOLD”
3. Repeat on left side. For now, adjust Brackets so notched edge is
perpendicular to the ground and screen has a slight rake.
Tighten to hold. Figure 3.
INSTALL WINDSHIELD TO MOTORCYCLE, ADJUST AND
TIGHTEN SECURLY
4. Refer to the SwitchBlade Owner’s Manual attached to the wind-
shield and install shield to motorcycle. Make final adjustments to rake
and tighten Nuts (4) firmly (15 ft/lbs.) (9/16 Socket and Wrench)
National Cycle, Inc. Maywood, IL 60153-0158 USA 708-343-0400 / Fax: [phone]
www.nationalcycle.com / e mail:[email protected]
Page 2 of 2 10-112210-000 07/04
Figure 3.
Figure 2. Right Side Bracket Assembly
Adjust bracket to “hold” with
notched edge perpendicular
to ground.
Final tightening is done after
installation of windshield to
motorcycle.
2
IJ
Bracket bends
outboard.
Bracket mounts
outboard.