Nav TV PCM3-AV User manual

PCM3-AV 2-3-2009
Rev 1.2 Mark Ryan
1 | Page
100 NW 11
TH
Street, Boca Raton, FL 33432
Tel. [phone] Fax. [phone]
www.nav-tv.com [email protected]
PCM3-AV
Emulates factory TV tuner. For input of an external audio/video source in 2009 and Up Cayenne vehicles.
What’s in the box Package Contents
1. A/V interface module
2. e with connector (1)
3. Optical
Optical cabl
cable (2)
cable acce
4. A/V Harness
5. Optical Coupler
6. USB cable (have the “A” connector side of the
ssible to the passenger side of the
vehicle cabin, but hidden from view)
7. RCA Male-Male adapter
Radio Removal Radio Dash Images
1. Insert a plastic pry tool into the space between the lower black
trim piece and the dash and gently pry the trim panel towards the
rear of the vehicle to release mounting clips. Follow the trim panel
around either clockwise or counterclockwise to release the
remainder of the mounting clips. Set aside the trim panel.
2. Remove (4) T-20 Torx screws from around the radio
3. Remove the radio, disconnect cables from radio, then set the
radio aside.
4. Remove fiber optic cable from radio harness.
5. Remove fiber cable from slot with arrow pointing away from radio.
6. With fiber optic coupler, extend to passenger under dash panel.
Plug into fiber optic connector provided with kit.
7. Run the free end of the fiber optic line to the empty slot.
8. Plug the other free in of the fiber optic line into factory optical
connector and reinsert in factory harness.
9. Plug fiber optic line into A/V box.
10. Plug in the main harness for the A/V box. Run power to the A/V
box in the dash behind radio. Connect to constant power and
ground.
11. Plug in filter into the A/V harness, hide behind radio.
12. Connect A/V source into unit.
13. Connect the (Red wire) on the A/V harness to constant +12volt
source.
14. Connect the (Black wire) on the A/V harness to ground.
15. Reassemble dash in reverse order.

If vehicle has factory rear view camera If vehicle has aftermarket rear view camera
1. Unplug RCA’s attached to the T-Harness
2. The RCA connector towards car, extend and plug into the
“Camera in” on the A/V box.
3. The RCA connector towards radio, extend and plug into
“video out” on the A/V box.
(Requires the PCM3CAM, BT, or Media kit, otherwise will
not show backup cam)
1. Unplug RCA’s attached to the T-harness.
2. The RCA connector towards car, do
nothing with.
3. The RCA connector towards radio, extend
and plug into “video out” on the A/V box.
4. Plug aftermarket rear view camera into
“camera in” on the A/V box.
12 Pin Molex wiring guide 12 Pin Molex connector image
Pin (1) Video out (high)
Pin (2) Video in (high)
Pin (4) Left audio (high)
Pin (3) Camera in (high)
Pin (5) Right audio (high)
Pin (6) Ground (Black wire)
Pin (7) Video out (low)
Pin (8) Video/CAM in (low)
Pin 10 Left/Right audio (low)
Pin (12) Constant +12volts In
Operation
Video in motion doesn’t need any programming just plug and play. Whenever a DVD is playing or an external video
source is on, the radio will always show an image.
To operate A/V input:
1. Press source button.
2. Press TV icon.
3. Under TV station presets, select preset #2 (play).
4. Then tap above preset icons in blank area to display image.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase.
2 | Page