Nav TV W205-RVC User manual

BHM
03/02/15
NTV-DOC203
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
W205-RVC
NTV-KIT580
Overview
The W205-RVC Kit allows the user to add a backup camera input (with active parking lines!) and
1 video input to the factory media screen in select 2015 Mercedes vehicles with the new
infotainment system. Installation is performed entirely behind the radio (disc player).
Kit Contents
CAM Input
Harness
Power/CAN Harness
LVDS
Video
Cable
Aux Video in Cable
W205-RVC Interface
CAM 6 NTV-KIT299
Optional Rear View Cam

BHM
03/02/15
NTV-DOC203
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Interface Connectors
Dip Switch Settings
Rear Camera
Aux Video
N/A [Must Stay UP]
Screen Size
Dip Sw:
1
2
3
4
5
6
UP
OFF
OFF
X
X
X
8.4” Monitor
DOWN
ON
ON
7” Monitor
Rear-CAM IN/CAM Power
Power/CAN
OUOUT
Dip Switches
*Note: Remove power to the unit prior to making
adjustments to the dip switches.
LVDS OUT
(to screen)
LVDS IN (from
radio)
Video IN

BHM
03/02/15
NTV-DOC203
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Dash Removal (’15 C-Class)
1. Use a plastic tool to remove the silver trim
behind the COMAND touchpad controller. You
will have to open the center console and press
the arm rest locks forwards for clearance:
2. Remove (2x) Torx 20 screws hidden
beneath the silver trim piece in
step 1:
3. Lift up the entire dash panel to just beneath the screen and
disconnect all (6) plugs. Set the dash panel aside in a safe
place.
4. Unscrew (2x) Torx 20 screws securing the radio to the sub
dash. These screws are not designed to be removed from the
radio clamps.
5. Remove the radio
by pulling it towards
you.

BHM
03/02/15
NTV-DOC203
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
Installation
1. With the radio removed, disconnect all harnesses and set the radio aside.
2. Gather the provided ‘Power/CAN Harness’ from the W205-RVC kit. Solder the
following wires to the smaller black plug, located in the car radio’s main power plug:
3. Locate the factory Dark Blue,4-pin round
connector (LVDS) that was removed from
the radio in step 1 from the port on the
radio labeled ‘DISP’. Connect this factory
plug to the W205-RVC interface at the port
labeled ‘LVDS OUT’.
Interface wires
Connect to car
Radio Plug
Black (Ground)
Chassis Ground
PIN 12 (Brown)
Yellow (Constant 12v)
Constant 12v (+)
PIN 15 (Red)
White (MON-CAN H)
CAN HI
PIN 38 (Black/White)
Green (MON-CAN L)
CAN LO
PIN 32 (Black)
White (PAS-CAN H)
CAN HI
PIN 37 (Yellow/White)
Green (PAS-CAN L)
CAN LO
PIN 31 (Yellow)
Orange
‘Reverse 12v
in’ wire from
this harness is
not used!

BHM
03/02/15
NTV-DOC203
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
4. Connect the smaller white plug
side of the provided LVDS
Video Cable to the port on
the W205-RVC interface
labeled ‘LVDS-IN’.
5. Connect the free end of the provided LVDS
Video Cable back to the factory radio at the
‘DISP’ (dark blue) port.
6. Connect the provided Cam input harness to the 4-pin port on
the W205-RVC interface labeled ‘CAMERA IN’.
7. Connect ground and ACC power for your camera to the
black (GROUND) and red (12V OUT) wires from the
provided CAM input harness. NOTE: This power source will
supply 12v ACC whenever CAN data is awake.
8. Connect the white plug from the ‘Power/CAN Harness’ to the port on the W205-RVC
interface labeled ‘POWER/CAN’.
9. Optional: If adding an additional video input, connect
the provided ‘Video in Harness’ to the 2-pin port
on the interface labeled ‘CAMERA IN’. Note: if AUX
Video/front camera is desired, dip switch #2 must be in
the ON (down) position. By default, placing the vehicle in drive will show this AUX video source
briefly. This option is selectable via the Menu, see ‘Operation’ on the next page.
10. Start the car and test for proper functionality before replacing any dash pieces.

BHM
03/02/15
NTV-DOC203
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
Parking Sensors Note
If this C-Class is not equipped with OEM
parking sensors, remove the displayed
sensor bar from the rear camera image
by entering into the MENU (see next
page) and selecting ‘OFF’ where
applicable under ‘Rear view camera
settings’. Don’t forget to select ‘Save’
when complete.
Basic Connection Diagram
PDC = Parking Sensors
Refer to page 4 for
wire connections

BHM
03/02/15
NTV-DOC203
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7 | P a g e
W205-RVC Operation
Once the W205-RVC is connected properly, reverse activation is automatic. Placing the
vehicle in reverse will display the connected camera’s image automatically.
Hold (5 seconds) to
enter Installer
MENU
Return
(Menu
control)
Navigate the menu
with the rocker knob
Hold (3 seconds) to
activate AUX Video (DIP
SW 2 must be DOWN)
COMAND TouchPad
Steering Wheel