Nav TV NTV-KIT586 User manual

RAM MULTI-CAM
RAM uConnect (RA4/RA3) 5-Camera / AUX AV / CIM Interface
NTV-KIT586
BHM
03/09/15
NTV-DOC204
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Overview
The RAM MULTI-CAM interfaces up to 5 cameras & 1 Auxiliary A/V source to the OEM
RA4/RA3 8.4” uConnect media screen in 2013+ RAM vehicles. All connected cameras are
displayed via data through factory controls. Turn signal camera activation is speed adjustable
via programming from the factory radio controls and LCD cluster.
Kit Contents
Front/Rear Swivel Camera
NTV-xxx
AVSW
NTV-KIT224
Plug & Play T-harness
NTV-HAR265
MULTI-CAM Module
NTV-ASY222
USB Cable (updates)
NTV-CAB009
RAM-CAM
Rear camera
NTV-KIT426
Turn Signal-Camera
NTV-xxx
Optional Cameras available
AUX A/V
Control in Motion
Cargo Cam
Rear View Cam
Auto Front Cam
Turn Signal Cams
Optional A/V switcher
(required for A/V input)
CAM Input
Harness
NTV-HAR267

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
RAM MULTI-CAM Connectors
18-PIN (Plug & Play T- Harness) connector
24-PIN (Cameras & I/O) Connector
PIN #
Description
Color
1
12v (+) Constant
Yellow
2
-Not Used-
Blue
3
-Not Used-
Orange
4
-Not Used-
--
5
-Not Used-
--
6
CAN (1) HI (radio side)
White/Black
7
CAN (0) HI (vehicle side)
Gray/Black
8
DIFF (+) (radio side)
Orange
9
DIFF (+) (vehicle side)
Blue
10
Ground (-)
Black
11
INPUT 2 (-)
Blue
12
INPUT 1 (+)
Gray
13
-Not Used-
--
14
-Not Used-
--
15
CAN (1) LO (radio side)
White
16
CAN (0) LO (vehicle side)
Gray
17
DIFF (-) (radio side)
Orange/White
18
DIFF (-) (vehicle side)
Blue
PIN #
Description
Color
1
Shield for Reverse-CAM RCA
Black
2
Shield for Front CAM RCA
Black
3
Shield for Right Turn RCA
Black
4
Shield for Left Turn RCA
Black
5
Shield for AUX VID RCA
Black
6
Shield for Cargo CAM RCA
Black
7
Ground OUT
8
-Not Used-
White
9
-Not Used-
White/Black
10
INPUT 4
Purple
11
INPUT 3 Retrofit PDC Monitor
Pink
12
UART RX
Brown/Black
13
Signal for Reverse-CAM RCA
Yellow
14
Signal for Front CAM RCA
Yellow
15
Signal for Right Turn RCA
Yellow
16
Signal for Left Turn RCA
Yellow
17
Signal for AUX VID RCA
Yellow
18
Signal for Cargo CAM RCA
Yellow
19
-Not Used-
--
20
-Not Used-
--
21
OUTPUT 3 Retrofit PDC Power
Red
22
OUTPUT 2 AUX AVSW TRIGGER
Blue/Red
23
OUPTUT 1 12v ACC
Gray/Red
24
UART TX
Brown
24-PIN
18-PIN
Wire Side
Wire Side

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
Dash Disassembly (RAM)
1. Remove the Torx t20 screw at the right rear of the pocket on the
right side of the dash.
2. Remove (2x) Torx t20 at the top of the dash. They are hidden beneath a rubber mat.
3. The face should be free now, pull straight
outwards (towards you) with medium force.
Use plastic panel tools if necessary.
4. Remove (4x) 7mm screws that secure the
LCD touchscreen.

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
RAM MULTI-CAM Module Installation
1. After removing the factory radio, grab the provided Plug & Play T-harness and connect the
female side to the factory 44-pin plug. Make certain the lock connects together securely.
2. Install all cameras and run signal/power leads into the front dash opening.
Camera Installation Notes:
a. 12v ACC is provided from output 1 (PIN 23, red). If connecting multiple
cameras, trigger a relay with this output instead to power your cameras!
b. Connect each camera signal to each yellow RCA per their specific labels (rear,
front, right TSC, left TSC etc).
c. The provided Plug & Play T-Harness contains red & black AUDIO RCA’s in the
center of the plug & play section. If not adding any AV source for this install,
connect these together (see diagram). If left disconnected, audio will not pass
through.
3. Optional: If installing aftermarket front sensors in addition to the MULTI-CAM,
connect the following wires for sensor-activated front-cam switching:
a. Connect the sensor main unit’s power wire to output 3 (PIN 21, pink) from the MULTI-
CAM
b. Splice the sensor main unit’s speaker signal lead (+) to input 3 (PIN 11, brown) from the
MULTI-CAM
4. Optional: If adding an additional A/V source (AVSW required), connect the following:
a. Connect output 2 (PIN 22, blue) to the white/red wire from the AVSW (not included).
Ground the black wire from the AVSW.
b. Connect the video signal from the AUX A/V unit to the RCA on the MULTI-CAM labeled
‘AUX’ (video ports on the AVSW are NOT used)
c. Connect the audio signal from the AUX A/V unit to the A1 input of the AVSW. This may
require the provided adapter.
d. Connect the black & red RCAs located in the Plug & Play T-Harness to the appropriate
red & white ports on the AVSW (see diagram: pg. 9)
Installation continues on next page…
AVSW
A1
Car side
Radio side

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
5. Optional: If the vehicle possesses both OEM cameras (reverse tailgate cam on the rearview
mirror and cargo cam on the main 8.4” screen), force both cameras to display on the main 8.4”
screen by completing the following:
a. Extend (splice, do not cut) the OEM tailgate signal with a pair of wires to the main radio
location. There are two easily accessible places for grabbing this RVC signal:
*Note: If the OEM tailgate RVC signal is cut in half, the mirror image will display an
error while in reverse. SPLICE into this wire, DO NOT CUT!
b. From the MULTI-CAM’s 18-pin connector, locate pins 9 & 18. Cut these wires in half
within a few inches of the connector.
c. Connect your extended pair of wires from step 5.a. to the 18-pin connector side of the
previously cut wires (green/orange to pin 18, green/brown to pin 9).
d. Extend the T-Harness side of the cut wires 9 & 18 (9 = [-], 18= [+]) with a single Male
RCA cable (not included) to the RCA labeled ‘Cargo Cam’ from the MULTI-CAM 24-pin
connector.
e. Make sure you set Cargo Cam to ‘FIX’ in NAVTV Settings while programming the MULTI-
CAM.
OR
Passenger’s side, behind
side dash panel
Driver’s side kick panel area
Green/Orange:
RVC (-)
Green/Brown:
RVC (+)
Green/Orange:
RVC (-)
Green/Brown:
RVC (+)
5.a.
Connect to
‘Cargo Cam’
RCA input

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7 | P a g e
6. Connect the RAM MULTI-CAM module to the 18-pin & 24-pin connectors found in the Plug &
Play T-Harness.
7. Connect the male side of the Plug & Play to harness the monitor. Reconnect all other plugs to
the monitor and proceed to Programming on Page 9.

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
8 | P a g e
Installation Diagrams
Cameras Only
RAM

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
9 | P a g e
With AV AUX and Sensors
RAM

BHM
03/09/15
NTV-DOC204
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
10 | P a g e
RAM MULTI-CAM Programming
Programming the RAM MULTI-CAM module is performed through the factory dash MUTE button,
TUNING KNOB, and CLUSTER LCD for feedback.
1. Before attempting to program, after making connections, let the vehicle perform a CAN-reset:
Close all doors/trunk/hood, lock the vehicle and waiting 5 minutes before proceeding to
program.
2. Turn the vehicle’s ignition on. Be certain you’re resting in FM
mode (see an FM station frequency on the cluster),
otherwise the cluster information may not display.
3. Close all doors (door status may override NAV-TV settings cluster feedback).
4. View the chart on the next page for settings descriptions and the diagram above to begin
programming.
5. NAV-TV programming mode will time out (back to factory) after 15 seconds. Scroll to the end of
the settings menu and select ‘EXIT’ to exit and save settings.
Press and HOLD
(15 seconds) to
enter NAV-TV
settings mode
While in NAV-TV
settings mode only:
Rotate clockwise
(slowly, one
detent/time) to
scroll through
options. Press ENTER
to change setting.
To show the FM source on the
cluster, first clear any messages
shown (door status, etc) with the UP
or DOWN arrows on the steering
wheel. Press the audio source
button until ‘FM’ is displayed.
Center button:
Change Audio Source