Nav TV W205-N RVC User manual

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
W205-N RVC
NTV-KIT703
Overview
The W205-N RVC Kit interfaces a backup camera input (with active parking lines) and 1 front
camera to the factory media screen in select 2015 Mercedes vehicles with the new
infotainment system.
Kit Contents
Plug & Play Power/CAN Harness
A-Type
LVDS
Video
Cable
W205-N RVC Interface
OSD Menu remote
IR Eye

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Interface Connectors
Dip Switch Settings
DIP SW
1
2
3
4
5
6
UP
KEEP
DOWN
KEEP
UP
OEM
CAM
VEH
TYPE
DOWN
KEEP
DOWN
KEEP
UP
Adding
CAM
VEH
TYPE
C-Class with 7” Screen C-Class with 8.4” Screen 2015 CLS, CLA, B & E-Class
Note: Remove power to the unit prior to
making adjustments to the dip switches.
Power/CAN
OUOUT
Video IN (from radio)
IR Eye
Not Used
CAN 2 Input
Video OUT (to screen)
Not Used
Dip Switches
C-Class
ONLY
NOT
C-Class
High
RES
Low
RES
2016+ SLC
2015 SL400, 7"

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Dash Removal (’15 C-Class)
1. Use a plastic tool to remove the silver trim
behind the COMAND touchpad controller. You
will have to open the center console and press
the arm rest locks forwards for clearance:
2. Remove (2x) Torx 20 screws hidden
beneath the silver trim piece in
step 1:
3. Lift up the entire dash panel to just beneath the screen and
disconnect all (6) plugs. Set the dash panel aside in a safe
place.
4. Unscrew (2x) Torx 20 screws securing the radio to the sub
dash. These screws are not designed to be removed from the
radio clamps.
5. Remove the radio
by pulling it towards
you.

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
Installation
1. With the radio removed, disconnect all harnesses and set the
radio aside.
2. In the main square radio plug, locate the 12-pin black plug and
remove it (press clip on top and pull).
3. Separate the outer shell from this OEM connector and insert the
provided 12-pin plug in its place (this connector only connects
properly in one direction).
4. Connect the OEM 12-pin to the female end of the plug & play portion of the harness
from step 3. Connect the new harness assembly back into the Main OEM Radio
connector like shown.
Main OEM
Radio Connector
OEM 12-pin
outer shell
Provided 12-PIN plug & play
OEM 12-PIN Harness
OEM 12-pin
& outer shell
NOTE: if you
insert this
connector upside
down, picture
will not display
at the monitor.

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
5. Locate the black and red wires labeled (GND) and
(ACC) and solder these wires to the ground wire
(PIN 12) and constant 12v power wire (PIN 15) on
the same quad-lock connector (from step 4):
6. Locate the OEM, typically Dark Blue,4-pin round
connector (LVDS) that was removed from the radio in step 1 from the port on the radio
labeled ‘DISP’. Connect this factory plug to the W204-H interface at the port labeled
‘VIDEO OUT’.
7. Connect the white plug side of the
provided LVDS Video Cable to the
port on the W204-H interface labeled
‘VIDEO-IN’.
8. Connect the free end (aqua) of the provided
LVDS Video Cable back to the factory radio at
the ‘DISP’ (dark blue) port.
NOTE: If there is no dark blue LVDS video plug present, use the cable that makes the OEM
screen disappear when unplugged (while radio is on).

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
9. Connect the small white 4-pin plug labeled ‘CAN2’ to the plug on the W205-N interface
labeled ‘CAN2’ for proper operation.
10. Power your reverse camera with an accessory 12v source, or use the brown wire for
reverse 12v only. Splice ground (-) to the black wire provided to the interface, or find
another ground point/wire in the car.
11. Connect signal from the rear camera to the RCA labeled ‘CAMERA’ among the main
Power/CAN harness.
12. Connect the white plug from the Power/CAN Harness to the port on the W204-H
interface labeled ‘POWER/CAN’.
13. Optional: If adding an additional video input (including front camera), use the provided
RCA labeled ‘FRONT’ for signal input. This video source must be powered with an ACC
source. NOTE: If the user desires for automatic front camera-switching, this option must
be set upon installation. See MENU Settings on page 8.
14. Start the car and test for proper functionality before replacing any dash pieces.
NOTE: If after
verifying DIP Switches and you still don’t get reverse activation (screen switching to cam-image
while in reverse), re-test with ALL dash-board pieces connected properly.
NOTE: If the above was tried and you still are not getting anything on screen, providing the green wire among
the CAN 2 Harness with a (+) reverse signal will switch the screen manually.

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7 | P a g e
W205-N RVC Install Diagram

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
8 | P a g e
Menu Adjustments
Before you start:
1
2
3
4
The IR-Eye must be connected
Make sure the car’s ignition is on and radio is on
You must be in Reverse Camera mode (place vehicle in reverse)
Repeatedly press the MODE button until guidelines appear on screen*
6The OSD Menu will appear on screen (auto-time out in about 5 seconds if
no action occurs).
To set Front Camera timer, scroll down using the remote arrow keys
when in the menu to FRONT CAMERA. Once in this setting, press OK
and choose (up/down) between 5, 7, 9 or 11 seconds for auto-front
switching timeout (once the vehicle leaves reverse gear, the front
camera input will stay active for pre-defined amount of time).
Functional Parking Guidelines ON/OFF
Not Used
Adjust FPG Position
Not Used
‘Safe to move?’ ON/OFF
To set custom green wire trigger, find 'REVERSE LINE' option
and set to 'REAR PORT' or 'AV1' depending upon your
preference. Every time the green wire recieves 12v (+), the
selected RCA port will display on screen.
5Now press the OK button 4 times, then press Power
NOTE- step 4
only required
if OEM reverse
camera exists

BHM
10/18/18
NTV-DOC245
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
9 | P a g e
W205-N RVC Operation
Once the W205-N RVC is connected properly, reverse activation is automatic. Placing
the vehicle in reverse will display the connected camera’s image automatically.
Note: If display doesn’t switch to reverse image when shifting into reverse, check dip switch
settings on page 2.
For forcing the Front Camera at any time, press the clear button OR the NAVI button
on the radio. On some vehicles, this is located on the steering wheel, others this is
located near the COMAND knob. Otherwise, the front camera will display for as long
as the setting was programmed (5,7,9 seconds, etc) once you leave Reverse gear.
Hold (2 seconds) to
activate AUX Video
C-Class Steering Wheel
CLS Comand knob
CLA
COMAND
knob
C Class Radio