Nav TV MY-CUE User manual

BHM
12/3/13
NTV-DOC150
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
MY-CUE Kit
NTV-KIT457
Overview
The MY-CUE Kit allows the user to add up to 3 audio/video inputs and a backup camera input to
the factory media screen in select GM vehicles equipped with either the MYLINK or CUE media
systems. This kit has a dedicated rear view camera input, 3 composite (RCA) audio/video inputs,
an RGB input and an AV output with AV switching. Audio integration requires that the vehicle
have a factory audio input.
Kit Contents
AV Input Harness
Power/CAN Harness
LVDS Video cable
MY-CUE Interface
Remote
RGB Input cable
Input Toggle Switch
IR Eye Harness

BHM
12/3/13
NTV-DOC150
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Interface Connectors
Dip Switch Settings* Configure prior to installation
Dip SW:
1
2
3
4
5
6
7
8
UP
Enables
RGB
Enables
V1
Enables
V2
Enables
V3
N/A
Leave up
N/A
Leave up
Factory or
no Rev-Cam
N/A
DOWN
Skips
RGB
Skips
V1
Skips
V2
Skips
V3
N/A
N/A
Activates
aftermarket
Rev-Cam
N/A
Leave
down
AV IN/OUT
OUOUT
RGB INPUT
OUOUT
Rear Camera Power
Power/CAN
OUOUT
Dip Switches
Status LEDs
*Note: If the dip switches are not configured prior to
installation you must remove power to the unit prior to
making adjustments to the dip switches. When power is
reconnected after the dip switch adjustment the new
settings will be stored into memory.
LCD IN/OUT
(LVDS Cable)

BHM
12/3/13
NTV-DOC150
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Factory GM HMI (Human Machine Interface)
Installation for GM trucks and notes for all other vehicles
THIS INTERFACE INSTALLS AT THE HMI MODULE, NOT AT THE SCREEN!
1. GM trucks only: Remove the glove box, the HMI module is located behind it (black box
with USB-type and other connectors). Remove (2x) Torx t15 screws:
2. GM trucks only: Underneath the glove box you’ll find (2x) more additional Torx T15
screws firing upwards. Remove these and pull the glove box free from the dash (all that
remain are clips).
Vehicle
HMI Location
Cadillac ATS/CTS
Directly below glove box
Cadillac SRX
Below/behind glove box
Corvette
Driver’s kick panel
Camaro
Beneath glove box
Silverado/Sierra
Behind glove box (high)
Colorado/Canyon
Behind screen (low)
Known HMI
Locations:

BHM
12/3/13
NTV-DOC150
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
3. Remove the blue mini-USB
connector shown here, and
replace it with the blue
male end of the provided
LVDS cable. Make sure the
connector is seated
properly.
4. Plug the factory blue mini-USB connector into the black,
female end of the provided LVDS cable.
5. Connect the white plug from the provided LVDS cable into the port on the MY-CUE
interface labeled ‘LVDS IN/OUT’.
6. Connect the AV Input cable to the port on the MY-CUE interface labeled ‘AV IN/OUT’. If
you’re only connecting a reverse camera (and no other
inputs), the signal input from the camera must connect
to the RCA labeled ‘REAR-C’. Refer to the dip-
switch settings chart to skip/enable AV sources
upon toggle switch presses (optional. Page 2).
a. The provided R-CAM output provides power (red) and ground (black) for the
aftermarket rear view camera.
b. If you’re installing a Nav-TV CAM 6
or Handle Cam, the power
connector plugs directly into the
MY-CUE interface port labeled ‘R-
CAM’.

BHM
12/3/13
NTV-DOC150
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
7. Optional: Connect the remote eye to the port labeled ‘IR’ (on the
power harness) and leave it in clear view of the driver (often it can
be stuck inside a vent). This connection would be necessary if you
want to be able to adjust anything from the MY-CUE interface’s
menu.
a. While in any AV mode other than factory (on the display
screen), press the MENU button for Menu 1 , or hold the
left arrow to enter MENU 2.
b. To switch between AV modes, press the ‘OK’ button.
8. Optional: Connect the provided momentary toggle switch to the
port on the MY-CUE interface labeled ‘MODE’. Pressing this switch with the ignition on
will cycle the screen modes as follows: factory screen > NAVI (RGB) > AV1 > AV2 > AV3
> factory screen. Please refer to the dipswitch section on
page 2 for input settings.
9. Connect the MY-CUE Power harness to the interface at the port labeled ‘POWER/CAN’.
Connect the RED wire to 12 volt + accessory and the BLACK wire to a clean and bare
ground connection.
10. If a rear view camera is being added connect the GREY wire to the 12v + reverse signal in
the vehicle (wire that shows 12 V+ only when in reverse). NOTE: when connecting to
ANY vehicle with LED reverse lights YOU MUST use a relay to isolate the factory wiring
from the interface. Connects are 30: output to grey wire form interface, 87: Constant 12
V + or 12 V + accessory, 85: Chassis ground, 86: Factory reverse wire, 87A No
connection.
11. Start the car and test for proper functionality before replacing dash pieces.
12. Note: All other included harnesses not mentioned in this manual are not needed for most
installations. If you would like to know more about the full capability of this interface,
contact NAV-TV tech support at 561-955-9770. Additional features not mentioned in this
manual are not supported by NAV-TV at this time.

BHM
12/3/13
NTV-DOC150
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
Menu Adjustments
Before you start:
Make sure the car’s ignition is on and radio is booted/settled
You must be in ‘NAVI’ (RGB), ‘AV1’, ‘AV2’ or ‘AV3’ mode (on
display screen)
Use the remote ‘OK’ button to switch modes, or use the
provided input toggle switch
Hold the LEFT ARROW for 3 seconds. The Menu of FACTORY will
appear on screen.
v
IMAGE MENU
-The only setting that may need
necessary adjustment here would
be CAR MODEL (BMW/AUDI KITs)
Note: on some kits, this option is
located under ‘UTIL’
-The remaining settings are
optional and install dependent.
PARK MENU
PARK ENABLE: Rear-CAM
guidelines ON/OFF
PARK SETUP: Rear-CAM guideline
positioning
REAR SELECT: Change rear camera
activation from CAN to LAMP (gray
wire) Note: on some kits, this
option is located under ‘UTIL’
SAFE ENABLE: If ‘ON’, prevents AV
sources from showing (unless you
ground Blue ‘PARKING’ wire)
Rear-Select CAN to LAMP adjustment
1
2

BHM
12/3/13
NTV-DOC150
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7 | P a g e
FAQs
Q. I cannot switch A/V sources.
A. Check IR or toggle switch connection. Check the LEDs on the interface, if nothing is lit
up with vehicle ignition, check power/ground connections.
Q. All I see on the display is a black screen (no factory image pass-through).
A. Make sure the video cables (IN/OUT) are connected at the proper location
(Screen/Radio/NAV DRIVE).
B. Make sure the video cables are seated all the way.
C. Make sure Dip Switches 5 & 6 are set correctly (resolution or screen size).
Q. Displayed image color is not proper (too dim or color seems wrong).
A. Try to select ‘INITIAL’ in OSD menu.
Q. Rear camera image does NOT appear.
A. Make certain Dip Switch #7 in set down for aftermarket camera, or up for a factory
camera.
B. Try swapping the CAN connection wires. This will not do damage, if it is hooked up
wrong it will only not work.
C. Make certain the camera is properly powered. Check voltage at the camera itself.
D. Try an alternative video source, don’t assume the power/ground is correct unless
you’ve checked it with a multi-meter!
E. If this is a CAN-connected module and you’ve connected the CAN wires, try using the
gray wire (not all interfaces have this wire!) instead of the CAN connection for reverse
activation. You’ll also need to change the Rear Select option in the Menu of Factory (MENU 2)
under UTIL or PARK. Refer to the Menu Adjustments section.
Q. Unwanted A/V mode is displayed upon a toggle press (A/V source switching order:
OEM->RGB->AV1->AV2->AV3->OEM).
A. Check DIP Switch Setting. Refer to page 2.