Nav TV PCM3CAM Manual

PCM3CAM
NTV-KIT100
Rev 2BHM 03/18/15
NTV-DOC045
3950 NW 120th Ave, Coral Springs, FL 33432
Tel. [phone] Fax. [phone]
www.nav-tv.com [email protected]
PCM3CAM-USB
Front and rear camera interface
Enables a backup camera and a secondary on the factory 2009 and Up Porsche PCM 3.0 Radios
Certain features are intended for passenger and off-road use only. User must obey
all State and Federal regulations
Make sure your radio looks like this prior to installation
Kit Contents
1 | Page
Filter Harness Description and Diagram
Wire Functions Wire Colors Fig. 2 - Connection plug on Can Filter
1. CAN Hi to Vehicle.
2. CAN Lo to Vehicle
3. Chassis Ground.
4. +12V Output to Camera.
5. CAN Hi to PCM.
6. CAN Lo to PCM.
7. +12V Battery
8. +12V Output to switcher and front Flir IR camera.
1. Yellow
2. Blue
3. Black
4. White/Red
5. Yellow
6. Blue
7. Red
8. White/Blue
8 pin Molex connector
Wire side view
PCM3-CAM Module
NTV-ASY107
Plug & Play Harness
NTV-HAR111
USB Cable (Updates)
NTV-CAB009
VSW-R Harness
NTV-HAR301
VSW-R Trigger
Harness
NTV-HAR066
VSW-R Board
NTV-ASY187
V1 Switcher shown
here, this has been
replaced with the
VSW-R in 03/15

Installation Part 1
1. Insert a soft pry tool into the space between the lower black fascia
piece and the lower side of the dash and gently pry the fascia towards
the rear of the vehicle to release the mounting clips. Follow the fascia
around either clockwise or counterclockwise to release the remainder of
the mounting clips. Set aside the fascia.
2. Remove (4) t20 torx screws from the sides of the
radio and pull the radio gently out of the dash in order
to disconnect all stock cables and antenna
connectors.
3. View of rear of radio and stock radio harness.
Remove the fiber optic connector from the original
harness by gently prying up on the locking tab with a
pick tool.
4. With the fiber unplugged from the factory harness
plug the aftermarket harness into the original harness
and secure it by closing the stock locking tab. Attach
the PCM3CAM module to the aftermarket harness
and secure the filter to the back of the radio cavity with
either double sided tape or Velcro. Fold the harness in
the cavity as shown to allow clearance for the radio.
2 | Page

Installation Part 2
5. Drop the plastic panel over the passenger side kick panel area
by taking out (1) t20 Torx screw and pulling the panel towards
the floor. Run the black, white/blue and white/red wires from the
new radio harness into the opening as in the picture to your left.
These wires will power your reverse and front cameras, as well
as the video switcher.
6. If your vehicle is not equipped with a stock camera and you are
not installing a front camera then simply unplug the male RCA end
from the female in the aftermarket harness and run your camera’s
video RCA directly to the female plug. Connect ground for the
reverse camera to the black wire and 12 volt positive to the
white/red from step 5 and insulate the white/blue wire. Skip to step
8.
Vehicles with factory camera VSW-R installation
7a. Extend and plug the female RCA (radio side) of the harness into AV1
out. Extend and plug the male RCA (vehicle side) into AV1 in. Connect a
front camera, for example, a Flir night vision camera RCA into Video 2 in.
Connect the black ground wire from step 5 to both the ground of the front
camera and the ground (black wire) from the video switcher. Connect the
12v wire (Video 2 Trig) of the switcher (white/red wire) to the white/blue
wire from the module.
Vehicles without factory camera switcher installation
7b. Extend and plug the female RCA (radio side) of the harness into
Video Output. Plug the RCA from your aftermarket rear viewcamera into
Video 1 input (VSW-R). Connect a front camera, for example, a Flir night
vision camera RCA into Video 2 in. Connect the black ground wire from
the switcher to the ground from the switcher, the reverse camera and the
front camera. Connect the white/red wire to the 12v wire to your
aftermarket back up camera. Connect the white/bluewire to the 12v wire
on your front vision camera
8. Plug the fiber optic cable you unplugged in step 3 into the aftermarket
harness. Reconnect all the antenna, power and all other connectors back
into the radio and slide the radio back into the dash. Reassemble in the
reverse order as steps 1,2 and 5. Now you are ready to proceed to the
programming and operations section. Good job!
3 | Page

Programming
4 | Page
1. With the radio booted fully, Press and hold the + button on
the steering wheel.
a. While continually holding down the + button, press and
hold down the mute button.
b. Continue to hold down the mute button and release the
+ button.
c. Continue holding MUTE until 'Service' appears on screen.
2. When SERVICE is displayed on the screen, press
and hold the up arrow for 4 seconds to program
the PCM for reverse camera.
3. After the radio reboots first select the option button on
the right of the PCM. Then select “rear view camera” and
then make sure the “automatic” feature is highlighted.
Automatic means that every time the vehicle goes into
reverse the PCM screen will show the backup camera
image.
Operation
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of pu ase.rch
This product is intended for off-road use and passenger entertainment only.
1. Place the vehicle in reverse and your image will appear on
the screen. When putting the vehicle back in drive the image
will stay on the screen for up to 20 seconds or until the
vehicle reaches 7 mph.
2. To enable the rear view camera while in motions simply
double click the mute button within 1 second. To deactivate
the camera while in motion double click the mute button
again.
3. It the switcher is used to switch between two cameras, the
double click the mute command will alternate between
reverse camera, factory screen, front camera, factory screen.
4. No matter what is showing on the screen the PCM will switch
over to the reverse camera image any time the vehicle is
placed into reverse.
5. This module is only intended for front and rear view cameras.
You will always have the “Pay Attention To Vehicles
Surroundings” disclaimer at the top of the screen.
Note: Camera will not operate when the rear hatch is open.
Continue to Step 2.
Read programming steps (1-2) completely before beginning, there is a timeout.
NOTE: If the PCM3-CAM module is ever removed from the original
vehicle, you must first enter service mode and press the down arrow
for 4 seconds to deprogram the original PCM BEFORE the filter is
removed. If this is not performed, the filter will not work on any
other vehicle.