Nav TV NTV-KIT495 User manual

MY-CUE VIM
Video in Motion for MyLink/CUE
NTV-KIT495
BHM
05/20/14
NTV-DOC181
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

BHM
05/20/14
NTV-DOC181
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Overview
The MY-CUE VIM enables video in motion, navigation destination input while in motion, and
Bluetooth setup while in motion in select 2013+ GM vehicles equipped with either the MyLink
or CUE media systems. Note: Video playback is only supported on vehicles that have factory
Rear Seat Entertainment installed.
Kit Contents
MY-CUE VIM pin out
Preliminary Note
The 20-pin connector that the installer needs to gain access to for the installation is
located at the radio tuner module. This is most commonly found close to the DVD player
and near the screen assembly. An image of the tuner module is shown below, with the
plug circled:
Pin #
Description
Color
1
12v Constant Power
Yellow
9
GMLAN (to RADIO)
Green
10
Ground (-)
Black
11
OUTPUT 1/ACC OUT
White/Red
18
GMLAN (to VEHICLE)
Purple
MY-CUE VIM Module
NTV-ASY161
Power Harness
NTV-HAR260
USB Cable (updates)
NTV-CAB009
Wire side

BHM
05/20/14
NTV-DOC181
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Dash Disassembly (Yukon)
1. Begin by raising the monitor with the button shown below (ignition is not required).
Leave the monitor in the upright position during dash disassembly.
2. Remove the dash
panel on the
passenger side
above the glove
box. It is secured
with clips only and
pulls straight out
(towards the rear
of the vehicle).
3. Remove the under-
dash on the driver’s side (beneath the steering wheel, not pictured). This requires that
you remove (2x) Torx T15 screws hidden
beneath the fuse panel cover on the
left side of the dash (hidden by the
driver’s door), and also (4x) T15 screws
underneath. After the screws have
been removed, the dash panel will pull
off straight towards you.
4. Remove (1x) 7mm screw from the
panel that secures the push to start
button, and pry the panel from the
sub-dash.

BHM
05/20/14
NTV-DOC181
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
5. Lift the center console armrest and remove the large trim panel containing the cup-
holders, 12v plugs and seat heaters/coolers. It is secured with clips only. Disconnect all
associated plugs and set this trim piece aside.
6. Remove (2x) 7mm screws that secure the
climate control onto the sub dash (one on
each lower corner). After the screws have
been removed, the climate control assembly
panel will pull straight out towards you (clips
secure it snugly). Remove all connectors and
set the panel
7. The radio tuner module is located just
beneath the DVD player, behind this panel.
Proceed to ‘Installation’ to complete the
install.
Installation
1. Locate the gray, 20-pin factory
connector located at the factory
tuner module and disconnect it.
2. In the same gray plug, locate PIN 14,
green wire (GM-LAN). Cut this wire
in half.

BHM
05/20/14
NTV-DOC181
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
3. From the provided Power Harness, solder pin 9, green wire to the plug side of the cut
wire from step 2.
4. From the provided Power Harness, solder pin 18, purple wire to the car side of the cut
wire from step 2.
5. Connect (splice) the following wires to the
16-pin factory green plug directly to the
left of the gray 20-pin:
6. Connect the VIM module to the 18-pin connector, and secure it inside the dash with zip-
ties or Velcro. Be sure not to affect any motorized monitor arms (if equipped).
7. Reinstall the dash pieces and proceed to ‘operation’ to test for proper functionality.
MY-CUE VIM Pin #
Description
Color (in green plug)
1, Yellow
12v (+) Constant
Pin 8; Red/Blue
10, Black
Ground (-)
Pin 16; Black

BHM
05/20/14
NTV-DOC181
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
My-CUE VIM Operation
To toggle Video in Motion, press the Rear Defrost button twice within 1 second. This
will enable any video to continue playing while driving. This feature will reset upon
every key cycle.
2x