Nav TV AUDI-09 INT MMi User manual

BHM
09/18/15
NTV-DOC164
rB3
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
AUDI-09 INT MMi
NTV-KIT186
Overview
The AUDI-09 INT MMi Kit allows the user to add up to 3 video inputs and a backup camera input
to the factory media screen in select Audi vehicles with the internal MMi media system (MMi
controls on vertical radio face, not console). Audio integration requires that the vehicle have a
factory audio input.
Kit Contents
AV Input Harness
Power/CAN Harness
Sub-Board cable
Audi 09 Interface
Remote
Video Sub-Board
LVDS Video Cable
IR Eye Harness
Input Toggle Switch

BHM
09/18/15
NTV-DOC164
rB3
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Interface Connectors
Dip Switch Settings* Configure prior to installation
Dip SW:
1
2
3
4
5
6
7
8
UP
Enables
RGB
Enables
V1
Enables
V2
Enables
V3
N.C.
N.C.
Factory or no Rev-
Cam
No Factory
NAV
DOWN
Skips
RGB
Skips
V1
Skips
V2
Skips
V3
N.C.
N.C.
Enables
Aftermarket R-CAM
Factory
NAV
AV IN/OUT
OUOUT
Power/CAN
OUOUT
Dip Switches
Status LEDs
*Note: If the dip switches are not configured prior to
installation you must remove power to the unit prior to
making adjustments to the dip switches.
LCD IN/OUT (Sub-
Board Cable)
Touch
IN/OU
T
OUOU
T
Camera power
LCD
OUT
(LVDS
Video
Cable)
From
Interface
(Sub-Board
Cable)
LCD-IN (from OEM cable)

BHM
09/18/15
NTV-DOC164
rB3
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Quick Connection Guide
Video cable installation happens behind the screen, no need to remove the radio
*Accessory can be found at the passenger fuse box, typically black/white or black/blue
Drop the glove box for easiest install
Use reverse light to trigger relay for reverse to Gray wire, otherwise intermittent
reverse activation may result!
If you have no factory image after connecting to the provided
sub-board, rotate the 10-pin square connector upside down.

BHM
09/18/15
NTV-DOC164
rB3
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
Installation
1. Remove the factory radio and screen. This usually requires pulling panels and removing
a series of screws. Disconnect any associated harnesses and set the radio and screen
aside.
2. Gather the provided ‘Power/CAN Harness’ from the AUDI 09 kit. Connect the following
wires to the car:
*Connect this wire to the output (pin 30) of a 12v SPDT relay. If no relay is used, reverse
activation may be intermittent.
Note: CAN connection is not supported at this time. You must connect the GRAY wire
to a reverse lamp for reverse activation!
3. Locate the keyed, 10-pin square connector that was removed
in step 1. Connect this factory plug to the provided Video Sub-
Board at the port labeled ‘LCD-IN’. Note: pay attention to the
orientation of this connector. There is a drawing that shows
you how to properly connect the plug via the keyway. If
connected backwards, the factory image will not pass
through properly.
4. Connect the smaller plug side of the provided LVDS Video Cable to the port on the
Video Sub-Board labeled ‘TO LCD’. As always, note
keyways.
5. Connect the free end of the provided LVDS Video Cable back to the factory LCD
monitor.
6. Connect the provided Sub-Board Cable to from the
port at the Video Sub-Board labeled ‘FROM I/F’.
Interface wires
Connect to car
Black (GND)
Chassis Ground
Red (ACC)
Accessory
Gray (Rear)
Reverse lamp 12v through a relay*
Note Keyway!

BHM
09/18/15
NTV-DOC164
rB3
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
7. Connect the free end of the Sub-Board Cable to the
main AUDI 09 interface at the port labeled ‘LCD-OUT’.
8. Connect the AV Input cable to the port on the AUDI 09 interface labeled ‘AV IN/OUT’. If
you’re only connecting a reverse camera (and no other
inputs), the signal input from the camera must connect
to the RCA labeled ‘REAR-C’. Refer to the dip-
switch settings chart to skip/enable AV sources
upon toggle switch presses (optional. Page 2).
9. Adjust dip switches on the AUDI 09 interface properly, refer to the chart on page 2 for
qualifications.
10. Connect the white plug from the ‘Power/CAN Harness’ to the port on the AUDI 09
interface labeled ‘Power/CAN’.
11. Optional: Connect the remote eye to the port labeled ‘IR’ (on the power harness) and
leave it in clear view of the driver (often it can be stuck inside a vent). This connection
would be necessary if you want to be able to adjust anything from the AUDI 09
interface’s menu. Refer to ‘Menu Adjustments’ for menu options.
12. Optional: Connect the provided momentary toggle switch to the port on the AUDI 09
Power/CAN harness labeled ‘MODE SW’. Pressing this switch with the ignition on will
cycle the screen modes as follows: factory screen > NAVI (RGB) > AV1 > AV2 > AV3 >
factory screen. Please refer to the dipswitch section on page 2
for input settings.
13. Start the car and test for proper functionality before replacing dash pieces.
14. Note: All other included harnesses not mentioned in this manual are not needed for most
installations. If you would like to know more about the full capability of this interface,
contact NAV-TV tech support at 561-955-9770. Additional features not mentioned in this
manual are not supported by NAV-TV at this time.

BHM
09/18/15
NTV-DOC164
rB3
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
Menu Adjustments
Before you start:
Make sure the car’s ignition is on and radio is booted/settled
You must be in ‘NAVI’ (RGB), ‘AV1’, ‘AV2’ or ‘AV3’ mode (on
display screen)
Use the remote ‘OK’ button to switch modes, or use the
provided input toggle switch
Hold the LEFT ARROW for 3 seconds. The Menu of FACTORY
will appear on screen.
v
IMAGE MENU
-The only setting that may need
necessary adjustment here would
be CAR MODEL (BMW/AUDI KITs)
Note: on some kits, this option is
located under ‘UTIL’
-The remaining settings are
optional and install dependent.
PARK MENU
PARK ENABLE: Rear-CAM
guidelines ON/OFF
PARK SETUP: Rear-CAM guideline
positioning
REAR SELECT: Change rear camera
activation from CAN to LAMP (gray
wire) Note: on some kits, this
option is located under ‘UTIL’
SAFE ENABLE: If ‘ON’, prevents AV
sources from showing (unless you
ground Blue ‘PARKING’ wire)
Rear-Select CAN to LAMP adjustment
1
2

BHM
09/18/15
NTV-DOC164
rB3
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7 | P a g e
FAQs
Q. I cannot switch A/V sources.
A. Check IR or toggle switch connection. Check the LEDs on the interface, if nothing is lit
up with vehicle ignition, check power/ground connections.
Q. All I see on the display is a black screen (no factory image pass-through).
A. Make sure the video cables (IN/OUT) are connected at the proper location
(Screen/Radio/NAV DRIVE).
B. Make sure the video cables are seated all the way.
C. Make sure Dip Switches 5 & 6 are set correctly (resolution or screen size).
D. Make sure the 10-pin, square plug from step 3 is connected in the proper orientation
(note keyway!).
Q. Displayed image color is not proper (too dim or color seems wrong).
A. Try to select ‘INITIAL’ in OSD menu.
Q. Rear camera image does NOT appear.
A. Make certain Dip Switch #7 in set down for aftermarket camera, or up for a factory
camera.
B. Try swapping the CAN connection wires. This will not do damage, if it is hooked up
wrong it will only not work.
C. Make certain the camera is properly powered. Check voltage at the camera itself.
D. Try an alternative video source, don’t assume the power/ground is correct unless
you’ve checked it with a multi-meter!
E. If this is a CAN-connected module and you’ve connected the CAN wires, try using the
gray wire (not all interfaces have this wire!) instead of the CAN connection for reverse
activation. You’ll also need to change the Rear Select option in the Menu of Factory (MENU 2)
under UTIL or PARK. Refer to the Menu Adjustments section.
Q. Unwanted A/V mode is displayed upon a toggle press (A/V source switching order:
OEM->RGB->AV1->AV2->AV3->OEM).
A. Check DIP Switch Setting. Refer to page 2.