Nav TV TOOKI-MB User manual

BHM
04/30/14
NTV-DOC058
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
TOOKI-MB
NTV-KIT043/112/288
Overview
The TOOKI-MB adds hands free calling to the factory MOST fiber optic system in select
Mercedes vehicles. If this Mercedes is equipped with MBRACE, this module is NOT compatible!
Kit Contents
TOOKI Module
NTV-ASY022
TOOKI MIC
NTV-MIC024
Power Harness
NTV-ASY007
Fiber Harness
NTV-ASY003
2x Fiber Coupler
NTV-CON001

BHM
04/30/14
NTV-DOC058
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Installation
1. Remove the factory radio, disconnect all harnesses and set it aside.
2. From the provided Power Harness, connect the black wire to
Ground (-). A ground wire can be found in the main power plug.
3. From the provided Power Harness, connect the yellow wire to
Constant 12v (+). A constant wire can be found in the main power plug.
4. Run the provided TOOKI MIC from the desired location to the MIC
port on the TOOKI module. The best location for mounting the
microphone is generally above the rearview mirror or the A-pillar.
5. Connect the provided Fiber Harness into
the factory MOST fiber system like shown
in the diagram here (right). This will
require removing the fiber connector
from the main radio power harness:
6. Reconnect one of the fiber pairs to the radio, connect the last free fiber pair to the
TOOKI module at the fiber port.
7. Connect the Power Harness to the power port on the TOOKI module.
8. If this vehicle is equipped with a phone module and/or an SOS
module, its fiber leads must be bypassed with the provided Fiber
coupler. Remove the fiber leads from the (factory) fiber connector,
and insert each end into one end of the coupler. Secure the leads
by closing the coupler. See next section ‘Factory Phone Verification’for qualifying this
vehicle.
Before
After
Factory MOST
Fiber Optic cable
Supplied NAV-TV
MOST Fiber
*Note: the factory MB microphone cannot be used with the TOOKI.

BHM
04/30/14
NTV-DOC058
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Factory Phone Verification
If this Mercedes is equipped with a factory phone module, it must be removed. The
module is usually located towards the front of the trunk under the carpet or under the
rear seat. On vehicles manufactured from ’03-’05, the TEL-AID module also must be
bypassed.
See step 8 (Installation) for bypassing instructions, see below to verify if this car has a
factory phone or not.
Press the ‘TEL’button on the radio:
TOOKI Commands
Factory phone module installed
No phone module installed
5*110011*1: Version & Date information
5*110011*3: TOOKI serial number
5*110011*4: Parrot Version
TOOKI Pairing
code: 6888
Press the ‘TEL’button, dial a code and press ‘SEND’