Nav TV PCM4-VIM User manual

PCM4-VIM
Video in Motion for Porsche PCM4.0
NTV-KIT802
BHM
12/20/16
NTV-DOC289
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

BHM
12/20/16
NTV-DOC289
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
2 | P a g e
Overview
The PCM4-VIM enables video to play while in motion (passenger entertainment only) for the new Porsche
PCM4.0-equipped infotainment radios. It will allow BT setup, DVD, USB, SD playback & Apply CarPlay
functionality while in motion. This kit is not currently plug & play and must be manually wired behind the
radio.
Kit Content
PCM4-VIM Pin Out
Pin
Description
Color
1
Constant 12v (+) IN
Yellow
4
INPUT 3 (VIM act)
Orange
8
CAN HI (radio)
White/Blue
9
CAN HI (car)
White/Brown
10
Ground (-)
Black
11
OUTPUT 1 (RAP ACC)
White/Red
12
OUTPUT 2 (REV OUT)
White/Blue
17
CAN LO (radio)
Blue
18
CAN LO (car)
Brown
PCM4-VIM Module
NTV-ASY256
VIM Module Harness
NTV-HAR128
USB Cable (updates)
NTV-CAB009
Wire Side
NOTE: All other wires in this harness are not used for this installation.

BHM
12/20/16
NTV-DOC289
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
3 | P a g e
PCM4-VIM Installation
1. Remove PCM4 radio. Disconnect all harnesses and set
the radio aside.
2. Connect the black wire to ground (-) and yellow wire to
constant 12v (+) in the main radio harness. Use the
image here (right) for visual aid (test wires!).
3. Locate the GRAY connector in the OEM quad-lock
connector. This is the connector which the CAN wires
must be spliced onto (yellow square, right).
4. On the gray connector mentioned in step 3, locate OEM
blue & blue/black twisted pair. Cut this pair of wires in
HALF.
5. Connect (solder) the following wires from the provided
VIM Module harness to the OEM wires:
6. Isolate new connections to radio harness and replace radio into sub-dash.
7. Optional (or for vehicles without SW control): Sending INPUT 3 (12v +) through a toggle (not included)
will activate VIM. Otherwise, an OEM button will control VIM activation normally.
8. Proceed to next section for PCM4-VIM functionality.
From VIM Module:
To OEM Harness:
PIN 8 (White/Blue)
Blue/Black, Radio side
PIN 9 (White/Brown)
Blue/Black, Car side
PIN 17 (Blue)
Blue, RADIO side
PIN 18 (Brown)
Blue, CAR side
12v (+)
Ground (-)

BHM
12/20/16
NTV-DOC289
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
4 | P a g e
PCM4-VIM Operation
While the vehicle is running, play a DVD or USB video on screen. Place car into drive, the video should
disappear. Press and HOLD ‘Return’on the steering wheel for 3 seconds and the video will return. This
action will reset upon each key-cycle.