Nav TV TOYCAM 2-EXP User manual

BHM
05/05/14
NTV-DOC187
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]m
TOYCAM 2-EXP
NTV-KIT450
Overview
The TOY-CAM kit includes a camera and harness to connect to the factory media screen in
select Toyotas. The signal connection to the radio is plug & play, however the camera will have
to be manually powered.
Kit Contents
Rear Camera
NTV-CAM061
Camera extension
CAM Power
Harness
Rear-Trigger Pin
Video T-Harness
RCA male to male
Hole-Saw

BHM
05/05/14
NTV-DOC187
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Installation
1. Remove the factory radio, disconnect all harnesses and set the radio aside.
2. Install the provided camera into the trunk lid. Be certain to check for clearance before
drilling any holes using the provided hole-saw.
3. Connect the provided Camera Extension to the camera and
run the RCA/power end forward to the dashboard opening.
4. Connect the black and red wires from the CAM power harness to ground (-) and ACC
12v (+). The radio must see the camera upon vehicle startup in order for the screen to
flip to the camera’s image when in reverse. You MUST connect the camera to an
accessory/ignition source and not a reverse light for proper operation!
Note: you can find ground (-)
and ACC 12v (+) at the radio’s
power harness (test!):
5. Connect the supplied video t-harness in the connector shown here (below). It is keyed
and will only fit in one direction:
6. Connect the camera’s
composite signal to
the RCA on the
provided Video input
harness, via the CAM
power harness.
7. Reconnect all the harnesses to radio, reassemble the dash and test by starting the car
and placing it into reverse. The reverse image should activate automatically (whenever
in reverse). If the radio does not transition in reverse and you’ve verified that the rest
Toyota Pin #
Description
Color
3
Accessory 12v (+)
Gray
7
Ground (-)
Brown

BHM
05/05/14
NTV-DOC187
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
of the installation is correct, proceed to step 8 to manually populate the provided
Rear-Trigger Pin (This includes verifying camera power from an ACC source!).
8. Perform this step only if nothing happens on the factory display when the vehicle is
placed into reverse:
a. Locate the 28-PIN plug on the back side of the radio and find the factory harness
that connects to it (if applicable, this harness may not be present).
b. If the plug is present, you’ll likely need to pry the pin-lock free on the back side
of the factory connector (look closely).
c. Insert the pin fully into the connector (or plug) in the position shown below:
d. Supply a 12v + signal while in reverse only (tap at reverse light) to the free end
of this Rear-Trigger Pin. Verify operation by placing vehicle into reverse.
(Pin side)